Advantech MIC-3042A User manual

Advantech CompactPCI™
Modular Industrial Computer
MIC-3042A/B
4U-High 8-slots
CompactPCI Platform
with Standard CPCI
Power Supply

MIC-3042 User Manual --- Page II
Copyright Notice
This document is copyrighted, 2004. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described in
this manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
Acknowledgements
PICMG™, CompactPCI™ and the PICMG™, CompactPCI™ logos are trademarks of
the PCI Industrial Computers Manufacturers Group. All other product names or
trademarks are properties of their respective owners.
CE Notification
The MIC-3042 series, developed by Advantech Co., Ltd., has passed the CE test for
environment specifications when shielded cables are used for external wiring. We
recommend the use of shielded cables.
P/N : 2002304200
September 2004

MIC-3042 User Manual --- Page III
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for one year from the date of
purchase.
This warranty does not apply to any products which have been repaired or altered
by persons other than repair personnel authorized by Advantech, or which have
been subject to misuse, abuse, accident or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is
defective, it will be repaired or replaced at no charge during the warranty period. For
out-of-warranty repairs, you will be billed according to the cost of replacement
materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. For example, CPU
speed, Advantech products used, other hardware and software used, etc. Note
anything abnormal and list any on-screen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt) in
a shippable container. A product returned without proof of the purchase date is not
eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to
your dealer.

MIC-3042 User Manual --- Page IV
Packing List
Before installation, ensure that the following materials have been received:
• One MIC-3042 CompactPCI™ enclosure with backplane
• One box of accessories
• One warranty certificate
• One CD-ROM for user manual (PDF file)
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3042 or any other Advantech
products, please visit our support website at:
• http://www.advantech.com.tw/support
For more information about Advantech's products and sales information, please
visit:
• http://www.advantech.com.

MIC-3042 User Manual --- Page V
Contents
1. General Information............................................ 1
1.1 Introduction ................................................................................. 2
1.2 Features ....................................................................................... 3
1.3 Specifications................................................................................. 3
1.3.1 General.......................................................................................... 3
1.3.2 Hot-swap Fans................................................................................. 3
1.3.3 Power Supply................................................................................... 4
1.4 Dimensions.................................................................................4
2. Installation………............................................... 6
2.1 Initial Inspection............................................................................. 7
2.2 The MIC-3042 Illustration ............................................................... 7
2.3 Installation Procedures ................................................................... 8
2.3.1 Card Installation and Removal........................................................... 8
2.3.2 Before Operating the System...........................................................10
2.3.3 Connecting with rear I/O module......................................................10
2.3.4 Replacing the Hot-swap Fan....................................................... 10
3. Backplane………….................................................. 11
3.1 General Information......................................................................12
3.2 Features......................................................................................12
3.3 Specification.................................................................................12
3.4 Slot Assignments……......................................................................12
3.5 Connector and jumper locations.......................................................15
3.5.1 ATX Power Connector (ATX1) .....................................................16
3.5.2 Power Switch .................................................................17
3.5.3 V I/O Voltage Selection ...............................................17
3.5.4 Fan Module Connector .................................................17
3.5.5 LED Board Connector ....................................................17
3.6 Clock Routing Configuration............................................................17
Appendix A (Pin assignment of connectors in MIC-3042A Backplane)……… 18
Appendix B (Pin assignment of connectors in MIC-3042B Backplane)……… 38
Appendix C (Ordering Information)…………………………………………… 54

MIC-3042 User Manual --- Page VI
Figures
Figure 1-1: MIC-3042 dimensions ........................................................................4
Figure 1-2: Appearance of MIC-3042......................................................................... 5
Figure 2-1: Front view of MIC-3042 ....................................................................7
Figure 2-2: Removable parts of MIC-3042....................................................................8
Figure 2-3: Installing a card into the chassis.....................................................9
Figure 3-1: MIC-3042A Backplane slot numbering ...................................................... 15
Figure 3-2: MIC-3042B Backplane slot numbering ...................................................... 15
Figure 3-3: The connector and jumper locations on the rear side (MIC-3042A)…........ 16
Figure 3-4: The connector and jumper locations on the rear side (MIC-3042B)…........ 16
Figure 3-5: V I/O voltage selection...................................................................... 19

MIC-3042 User Manual --- Page 1
1
General Information

MIC-3042 User Manual --- Page 2
1.1 Introduction
The MIC-3042 series are a 4U-high enclosure designed for standard CPCI power
supplies which means an extremely low mean-time-to-repair (MTTR) since each
power supply can be hot-swapped. It equips with a 6U 8-slot CompactPCI H.110 CT
bus backplane and a 500W 2+1 redundant AC/DC power supply. It is suitable for
telecommunication, computer telephony integration, and industrial automation. The
built-in high quality backplane with 64 bit / 66MHz bus speed offers best impedance
control, meets open architecture standards and is compatible with all Advantech
CompactPCI boards.
The MIC-3042 series support IEEE 1101.11 rear I/O transition board. Users can
route I/O signals to the rear transition board to simplify system cabling. Front boards
pop in and out without any hardwiring. Efficient hot swappable fan module gives easy
self-maintenance capability. The system slots can support CPU boards featuring
desktop Intel®Pentium®IV Processor-M up to 2.2GHz with MIC-3358 series and
Intel®Pentium®M processors up to 1.8GHz with MIC-3369 series. With the chassis
management module (MIC-3924L-A), the chassis temperature and fan speed can be
monitored and the MIC-3924L-A will issue sound to alarm while any abnormal.
The MIC-3042A supports PICMG 2.16 and can be used as blade servers. Moreover,
the MIC-3042B supports slim CD-ROM or FDD using MIC-3960 media carrier board.
With redundant industry standard CompactPCI power supply plus Advantech’s
renowned reliability, the MIC-3042 4U enclosure is a rock solid choice for
communications and telephony applications.
There are four models of MIC-3042 series :
• MIC-3042A-A: MIC-3042A enclosure, w/ 8-slot CompactPCI™ 6U backplane
(MIC-3042A) supporting CT bus application and PICMG 2.16, and 500W 2+1
redundant AC CPCI power supplies.
• MIC-3042A-D: MIC-3042A enclosure, w/ 8-slot CompactPCI™ 6U backplane
(MIC-3042A) supporting CT bus application and PICMG 2.16, and 500W 2+1
redundant DC CPCI power supplies.
• MIC-3042B-A: MIC-3042B enclosure, w/ 8-slot CompactPCI™ 6U backplane
(MIC-3042B) supporting CT bus application and 500W 2+1 redundant AC CPCI
power supplies.
• MIC-3042B-D: MIC-3042B enclosure, w/ 8-slot CompactPCI™ 6U backplane

MIC-3042 User Manual --- Page 3
(MIC-3042B) supporting CT bus application and 500W 2+1 redundant DC CPCI
power supplies.
1.2 Features
• Eight 6U card slots
• Supports front and rear I/O
• Supports H.110 CT application
• 500W 2+1 redundant AC/DC power supply
• Hot-swap compliant backplane
• A hot-swap fan module
• Integrated intelligent management module,MIC-3924L, which can monitor the
chassis temperature and fan speed and issue alarm while any abnormal.
1.3 Specifications
1.3.1 General
• Construction: Aluminum frame and galvanized sheet steel
• 8-slot space (32 TE), including one system slot and seven peripheral slots for
MIC-3042A and six peripheral slots and one media slot for MIC-3042B
• "Hot swappable” platform complies with PICMG 2.1 R 2.0 Hot Swap
Specification
• Dimensions (W x H x D, mounting flanges not included):
4U: 440 x 177 x 320 mm (17.3" x 7" x 12.6")
• Weight: 18 kg (39.7 lb)
• Operating temperature: 0 ~ 45° C
• Storage temperature: -20° C ~ 60° C
• Relative humidity: 10 ~ 95% @ 40° C, non-condensing
• Operating altitude: 0 ~ 3,048 meters (0 ~ 10,000 feet)
• Storage/transit altitude: 0 ~ 12,190 meters (40,000 feet)
• Shock: 10 G (operating); 30 G (storage/transit)
• Random vibration: 1.0 Grms (operating); 2.0 Grms (operating)
1.3.2 Hot-swap Fans
• Air flow: One 193-CFM front fan and one 61.3-CFM rear fan
• Rated fan speed: 3,000 rpm (front fan); 3,400 rpm (rear fran)

MIC-3042 User Manual --- Page 4
• Life expectancy: 80,000 hours @ 40° C (front fan); 50,000 hours @ 25° C (rear
fan)
1.3.3 Power Supply
• Input:
AC: 100~240 V @ 47~63 Hz, full range (for MIC-3042X-A models)
DC: -48V (TYP), -36~-72V range (for MIC-3042X-D models)
• Output: 500W+250W 2+1 hot swappable and redundant AC or DC w/PFC
• Maximum load: +3.3V @ 36A, +5V @ 50A, +12V @ 10A, -12V @ 1A
• Minimum load: +3.3 V @ 0A, + 5V @ 2A, +12 V @ 0A, -12V @ 0A
• MTBF: AC: 266,241 hours @ 25° C; DC: 92,859 hours @ 30° C
• Safety: UL/CE/TUV
1.4 Dimensions
Figure 1-1: MIC-3042 dimensions.

MIC-3042 User Manual --- Page 5
Figure 1-2: Appearance of MIC-3042

MIC-3042 User Manual --- Page 6
2
Installation

MIC-3042 User Manual --- Page 7
2.1 Initial Inspection
We have carefully inspected the MIC-3042 series mechanically and electrically
before shipping. It should be free of marks and scratches and in perfect working
order upon receipt. As you unpack the MIC-3042 series, check it for signs of shipping
damage (damaged box, scratches, dents, etc.). If it is damaged or fails to meet
specifications, notify our service department or your local representative
immediately. Also notify the carrier. Retain the shipping carton and packing material
for inspection by the carrier. After inspection, we will make arrangements to repair or
replace the unit.
Warning!!! We strongly recommend that only qualified, experienced
personnel install or remove components. They must exercise extreme
caution when doing so.
Warning!!! Service personnel must make sure that the power cord has
been pull out before striping down any component. After service, ground
wire have to be connected certainly before power cord.
2.2 The MIC-3042 Illustration
The MIC-3042 series are designed to be installed and maintained easily.
Figure 2-1 and Figure 2-2 illustrate important components on the front and hot
swappable parts of the enclosure.
Figure 2-1: Front view of MIC-3042

MIC-3042 User Manual --- Page 8
Figure 2-2: Removable parts of MIC-3042
2.3 Installation Procedures
2.3.1 Card Installation and Removal
The CompactPCI™ connectors are firm and rigid, and require careful handling while
plugging and unplugging. Improper installation of a card can easily damage the
backplane of the chassis.
The system card can be installed only in the system slot. Do not insert the system
card into any other slot, or insert a peripheral card into the system slot. The system
slot is marked by a triangle enclosing the slot number 1 for MIC-3042A and 2 for
MIC-3042B. Please refer to the Appendix A and Appendix B for detailed backplane
information
The insert/eject handles on CompactPCI™ cards help users to install and remove the
cards easily and safely. Follow the procedures below to install a card into a chassis:
To install a card:
1. Hold the card horizontally. Be sure that the card is oriented correctly.
The components of the card should be pointing to the up side.
2. Be sure that the handles of the card are not latched. Release the handles if they
are latched. Handles from different vendors may have different latch designs.
Caution!!! Keep your fingers away from the latch hinges to prevent your
fingers from getting pinched.

MIC-3042 User Manual --- Page 9
3. Insert the card into the chassis by sliding the left and right edges of the card into
the card guides.
4. Push the card into the slot gently by sliding the card along the card guide until the
handles meet the rectangular holes of the cross rails. 1 2
Figure 2-3: Installing a card into the chassis
Note: If the card is correctly positioned and has been slid all the way into
the chassis, the handles should match the rectangular holes. If not, remove
the card from the card guide and repeat step 3 again. Do not try to install a
card by forcing it into the chassis.
5. Pull the right handle to the left and pull the left handle to the right to push the card
into place and fixed.
6. Secure the card by locking the handles into place.
To remove a card:
1. Unscrew the screws on the card front panel. Release the locking latches on the
handles.
2. To push the red buttons on the right and left handles to loosen the card from the
backplane.
3. Slide the card out.

MIC-3042 User Manual --- Page 10
2.3.2 Before Operating the System
Before operating your system, check your power supply source firstly.
Adjust the switch on the power supply to the correct voltage.
Two mounting flanges are included for users who would like to install the MIC-3042
on a 19" rack.
2.3.3 Connecting with rear I/O module
The MIC-3042 is limited to be used with rear I/O module. To install the RIO module,
please follow the steps below:
1. Remove the blank panel above the system RIO slot. (Suggest to remove all the
blank panels for installation)
2. Connecting with the right connector on board, and slide into the card cage.
3. Power up the system and check all the storage devices work properly.
2.3.4 Replacing the Hot-swap Fan
The MIC-3042 provides two hot-swap fans, one is at the front side and another is at
the rear side. Please refer to Figure 2-2. It can be removed without turning off the
system power or interrupting system operation.
Follow these steps to replace a fan:
1. Unfasten the fan's holder.
2. Slide the fan's holder out.
3. Replace the old fan with a new one.
4. Slide the fan's holder in.
5. Fasten the new fan's holder.

MIC-3042 User Manual --- Page 11
3
Backplane

MIC-3042 User Manual --- Page 12
3.1 General Information
There are two kinds of backplanes for MIC-3042 series. MIC-3042A and MIC-3042B
are with H.110 CT bus backplane. Both backplanes provide eight CompactPCI™ slots
with one slot dedicated to the CPU board. The MIC-3042 supports front I/O wiring,
providing simplified system cabling. The backplane also provides several 3-pin
connectors to connect hot-swappable cooling fan module. In order to provide users
with a flexible system configuration, the MIC-3042 includes one standard ATX power
connector to accept one ATX power supply. The MIC-3042 complies with PICMG 2.1
Hot-Swap Specification, providing full hot-swapping capability. Users can build a
hot-swap system using hot-swap plug-in boards and software.
3.2 Features
• Eight CompactPCI™slots (one system slot and seven peripheral slots)
• 64-bit PCI bus compliant
• Complies with PICMG 2.1 Hot-Swap Specification
• Accepts redundant AC/DC power supply
• Chassis alarm module for environment monitoring.
• Hot-swappable fan interface.
3.3 Specification
• Eight CompactPCI™ slots (one system slot and seven peripheral slots)
• Bus width: 64-bit
• 10-layer PCB (for MIC-3042A); 8-layer PCB (for MIC-3042B); 3.0 mm thick
• Power connector: One ATX power connector for connecting standard ATX power
supply
• Complies with CompactPCI™ Specification PICMG 2.0, R.3.0
• Complies with CompactPCI™ Hot Swap Specification PICMG 2.1, R2.0.
• Complies with CompactPCI™ Computer Telephony PICMG2.5, R1.0 (optional)
• Dimensions: 440 x 177 x 320 mm (17.3” x 7” x 12.6”)
• Operating temperature: -5 ° C ~ 80° C
3.4 Slot Assignments
The CompactPCI™specification defines slot numbering separation for physical and
logical slots. Each slot has a physical number and a logical number (refer to the
CompactPCI™ specification version 2.0 R3.0 for further information on slot
assignments). The physical numbers are printed on the backplane, enclosed in
circles or triangles. Slot1 of MIB-3042A and slot2 of MIC-3042B, marked by a
triangle, is the system slot and can only be used by a CPU board. The other slots are

MIC-3042 User Manual --- Page 13
peripheral slots. The logical number of each slot is defined according to the IDSEL
signal and the associated address used to select the slot. Table 3-1 shows the system
slot and peripheral slots relationships on the backplane. The system slot has a logical
number of 1 (for MIC-3042A) or 2 (for MIC-3042B), and the peripheral slot has a
logical number of 2~8 for MIC-3042A or 1, 3-8 for MIC-3042B. The connectors in
logical slot 1 are designated as 1-P1, 1-P2, and 1-P3 from the bottom up.
Nomenclature for connectors in the other slot is similar, such as 2-P1 and 2-P2.
Connector P1 on the system slot is a keyed connector providing 32-bit CompactPCI™
bus between the system slot and the peripheral slot. Connector P2 on the system slot
is an un-keyed connector providing 64-bit CompactPCI™ bus between the system
slot and the peripheral slots. Connector P3 on the system slot is open for user
definition.
Please check appendix A for the pin assignment for all the connectors on the
backplane.
Table 3-1 : MIC-3042A System to peripheral slot signal assignment.
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 2)
CLK0 P1:D6 CLK P1:D6
AD31 P1:E6 IDSEL P1:B9
REQ0# P1:A6 REQ# P1:A6
GNT0# P1:E5 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 3)
CLK1 P2:A1 CLK P1:D6
AD30 P1:A7 IDSEL P1:B9
REQ1# P2:C1 REQ# P1:A6
GNT1# P2:D1 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 4)
CLK2 P2:A2 CLK P1:D6
AD29 P1:B7 IDSEL P1:B9
REQ2# P2:E2 REQ# P1:A6
GNT2# P2:D2 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 5)
CLK3 P2:B2 CLK P1:D6
AD28 P1:C7 IDSEL P1:B9
REQ3# P2:E2 REQ# P1:A6
GNT3# P2:C3 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 6)
CLK4 P2:A3 CLK P1:D6
AD27 P1:E7 IDSEL P1:B9
REQ4# P2:A3 REQ# P1:A6
GNT4# P2:E3 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 7)
CLK5 P2:A20 CLK P1:D6
AD26 P1:A8 IDSEL P1:B9
REQ5# P2:D15 REQ# P1:A6

MIC-3042 User Manual --- Page 14
GNT5# P2:E15 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 8)
CLK6 P2:A21 CLK P1:D6
AD25 P1:D8 IDSEL P1:B9
REQ6# P2:A17 REQ# P1:A6
GNT6# P2:E17 GNT# P1:E5
Table 3-2 : MIC-3042B System to peripheral slot signal assignment.
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 1)
CLK0 P1:D6 CLK P1:D6
AD31 P1:E6 IDSEL P1:B9
REQ0# P1:A6 REQ# P1:A6
GNT0# P1:E5 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 3)
CLK1 P2:A1 CLK P1:D6
AD30 P1:A7 IDSEL P1:B9
REQ1# P2:C1 REQ# P1:A6
GNT1# P2:D1 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 4)
CLK2 P2:A2 CLK P1:D6
AD29 P1:B7 IDSEL P1:B9
REQ2# P2:E2 REQ# P1:A6
GNT2# P2:D2 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 5)
CLK3 P2:B2 CLK P1:D6
AD28 P1:C7 IDSEL P1:B9
REQ3# P2:E2 REQ# P1:A6
GNT3# P2:C3 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 6)
CLK4 P2:A3 CLK P1:D6
AD27 P1:E7 IDSEL P1:B9
REQ4# P2:A3 REQ# P1:A6
GNT4# P2:E3 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 7)
CLK5 P2:A20 CLK P1:D6
AD26 P1:A8 IDSEL P1:B9
REQ5# P2:D15 REQ# P1:A6
GNT5# P2:E15 GNT# P1:E5
System Slot (Logical Slot 2) Peripheral Slot (Logical Slot 8)
CLK6 P2:A21 CLK P1:D6
AD25 P1:D8 IDSEL P1:B9
REQ6# P2:A17 REQ# P1:A6
GNT6# P2:E17 GNT# P1:E5