Advantech AIIS-E730 Installation and operation manual

1 Startup Manual
Packing List
Before installation, please make sure that you have received
the following:
• AIIS-E730 card
• Quick Start User Manual
If anything is missing or damaged, contact your distributor or
sales representative immediately.
Specications
Isolated Digital Input
Number of Channel 16 (bi-directional)
Optical Isolation 2,500 VDC
Opto-isolator response time 25 μs
Over-voltage Protect 70 VDC
Input Voltage
VIH (max.) 30 VDC
VIH (min.) 3 VDC
VIL (max.) 1 VDC
Input Current
3 VDC 0.5 mA (typical)
12 VDC 3.1 mA (typical)
24 VDC 6.6 mA (typical)
30 VDC 9.73 mA (typical)
Declaration of Conformity
FCC Class A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause interference in which case the user is
required to correct interference at his own expense.
CE
This product has passed the CE test for environmental
specifications when shielded cables are used for external
wiring. We recommend the use of shielded cables. This kind
of cable is available from Advantech. Please contact your
local supplier for ordering information.
Notes
For more information on this and other Advantech products,
please visit our websites at:
http://www.advantech.com
For technical support and service:
http://www.advantech.com/support/
This startup manual is for AIIS-E730.
Part No: 2003F73000 1st Edition
January 2016
STARTUP MANUAL
Overview
AIIS-E730
32-channel Isolated Digital I/O Card
The AIIS-E730 offers isolated digital input channels as well
as isolated digital output channels with isolation protec-
tion up to 2,500 VDC, which makes them ideal for industrial
applications where high-voltage isolation is required. The
AIIS-E730 also features a Digital filter on each channel.
General
I/O Connector Type 37-pin box header
Dimensions 96 mm x 102 mm (3.8” x 4.0”)
Power Consumption
Typical +3.3 V @ 265 mA
+12 V @ 40 mA
Max +3.3 V @ 475 mA
+12 V @ 75 mA
Temperature
Operation 0 ~ 50°C (32~ 122 °F )
(refer to IEC 68 -2 - 1 ,2)
Storage -20 ~ +70°C (-4 ~158°F)
Relative Humidity 5 ~ 95% RH non-condensing
(refer to IEC 60068-2-3)
Certication CE/FCC
Digital Output
Number of Channels 16
Optical Isolation 2,500 VDC
Output Voltage Open collector 5 to 40 VDC
Sink/Source Current 500 mA max./channel

Startup Manual 2
STARTUP MANUAL
PIN Assignments
Specications
Digital Filter Time
Digital Filter Time[sec.] = 2n / (8 x 106) n: = setting data(0 - 20)
Setting Data (n) Digital Filter
Time Setting Data (n) Digital Filter Time Setting Data (n) Digital Filter Time
0 (00h) The filter function is
not used. 7 (07h) 16μsec 14 (0Eh) 2.048msec
1 (01h) 0.25μsec 8 (08h) 32μsec 15 (0Fh) 4.096msec
2 (02h) 0.5μsec 9 (09h) 64μsec 16 (10h) 8.192msec
3 (03h) 1μsec 10 (0Ah) 128μsec 17 (11h) 16.384msec
4 (04h) 2μsec 11 (0Bh) 256μsec 18 (12h) 32.768msec
5 (05h) 4μsec 12 (0Ch) 512μsec 19 (13h) 65.536msec
6 (06h) 8μsec 13 (0Dh) 1.024msec 20 (14h) 131.072msec
Description of pin use:
IDIn (n=0 ~ 15): Isolated digital input
IDOn (n=0 ~ 15): Isolated digital output
ECOM: External common Vcc/GND of IDI
PCOM: Free wheeling common diode for IDO
EGND: External ground for IDO

Startup Manual 3
Connections
Isolated Digital Input
Each of the 16 isolated digital input channels accept
voltage from 3 to 30 V for logic high, and 0 to 1 V for logic
low. All input channels share one external common. The
following figure shows how to connect an external input
source to the card's isolated inputs.
Isolated Digital Output
The AIIS-E730 provides 16 isolated DO channels. If the
external voltage (5 ~ 40V) is connected to each isolated
output channel (IDO) and its isolated digital output turns
on (500 mA per channel maximum), the card's current will
sink from the external voltage.