Advantech PCE-3032 User manual

User Manual
PCE-3032/4132
LGA1200 Intel® Xeon, Core™ i9/
i7/i5/i3/Celeron®/Pentium®
PICMG 1.3 Half-size System Host
Board with VGA/DVI-D/DDR4/
SATA3.0/USB3.2/Dual GbE

PCE-3032/4132 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2021
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
AMIBIOS is a trademark of American Megatrends Inc.
Intel®, Core™ i9/i7/i5/i3, Pentium®, Celeron and Xeon are trademarks of Intel® Cor-
poration.
Nuvoton is a trademark of Nuvoton Technology Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product is defective, follow the steps outlined below:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2001303200 Edition 1
Printed in China November 2021

iii PCE-3032/4132 User Manual
Declaration of Conformity
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference. In
this event, users are required to correct the interference at their own expense.
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

PCE-3032/4132 User Manual iv
Backplane Support Matrix Table
Specification Comparison
Backplane
Model
processor
PCE-3BXX PCE-4BXX
PCE-3032G2-00A1E Yes -
PCE-4132G2-00A1E Yes Yes
Note! If PCE-3032/4132 is used on different backplanes which has different
PCIe configuration. Below message would be showed on first time
power on, and user has to turn off AC power and then turn on for PCIe
re-configuration.
Caution! PCIe configuration error! Please turn off AC power before re-configura-
tion.
Part
Number PCH Memory VGA DVI-D** Backplane LAN SATAIII m-SATA USB 3.0
USB
2.0
S/W
RAID
mini-
PCIe*
PCE-
3032G2-
00A1E
H420E Non-ECC 1 1 PCE-3BXX 2 3 0 4 6 No 0
PCE-
4132G2-
00A1E
W480E ECC/
Non-ECC 1 1
PCE-
3BXX/
PCE-4BXX
2 4 0 4 6 Yes 1
Note! * Optional PCE-SA01-00A1E is required. PCE-SA01-00A1E is compati-
ble with IPC-3026/IPC-6806S/ACP-4D00/ACP-4020 chassis, but not
IPC-3012 chassis.
** Optional DVI-D cable 1700021831-01 is required.

v PCE-3032/4132 User Manual
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:
1 x PCE-3032 or 4132 PICMG 1.3 System Host Board
1 x PCE-3032/PCE-4132 start-up manual
1 x Serial ATA HDD data cable
1 x 2-port COM cable kit
1 x 4-port USB 2.0 cable kit
1 x 2-port USB 3.0 cable kit
1 x 1-port LPT cable kit
Power converter (Connecting from peripheral power connector on power supply
to PWR1 on board)
1 x Warranty card
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the PCE-3032/4132 mechani-
cally and electrically before shipment. It should be free of marks and scratches and in
perfect working order upon receipt. As you unpack the PCE-3032/4132, check it for
signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is
damaged or it fails to meet the specifications, notify our service department or your
local sales representative immediately. Also notify the carrier. Retain the shipping
carton and packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.

PCE-3032/4132 User Manual vi

vii PCE-3032/4132 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ............................................................................................... 2
1.2 Features & Benefits................................................................................... 2
1.3 Specifications............................................................................................ 3
1.3.1 System .......................................................................................... 3
1.3.2 Memory ......................................................................................... 3
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 4
1.3.6 Industrial Features ........................................................................ 4
1.3.7 Mechanical and Environmental Specifications.............................. 4
1.4 Jumpers and Connectors .......................................................................... 5
Table 1.1: Jumper List ................................................................. 5
Table 1.2: Connectors ................................................................. 5
1.5 Board Layout: Jumper and Connector Locations...................................... 6
Figure 1.1 Jumper and Connector Locations............................... 6
1.6 Block Diagram........................................................................................... 7
Figure 1.2 PCE-3032 Block Diagram........................................... 7
Figure 1.3 PCE-4132 Block Diagram........................................... 7
1.7 Safety Precautions.................................................................................... 8
1.8 Jumper Settings ........................................................................................ 8
1.8.1 How to Set Jumpers...................................................................... 8
1.8.2 BIOS (JCMOS1) ........................................................................... 9
Table 1.3: Clear BIOS CMOS (JCMOS1).................................... 9
1.8.3 ME Enable (JME1)........................................................................ 9
Table 1.4: JCMOS1/JME1: Clear CMOS/ME FW Update........... 9
1.8.4 Watchdog Timer Output (JWDT1) and Hardware Monitor Alarm
(JOBS1) ...................................................................................... 10
Table 1.5: Watch Dog Timer (JWDT1) and Hardware Monitor
Alarm (JOBS1) ......................................................... 10
1.9 System Memory ...................................................................................... 10
Chapter 2 Connecting Peripherals ....................11
2.1 Introduction ............................................................................................. 12
2.2 USB Ports (USB2A1, USB2C1, USB3C1, USB3C2, USB2H1, USB2H2,
USB3H1) ................................................................................................. 12
2.3 VGA Connector (VGA)............................................................................ 13
2.4 DP Connector (DP2) ............................................................................... 13
2.5 RS-232 Serial Ports (COM12)................................................................. 14
2.6 CPU Fan Connector (CPUFAN1)............................................................ 14
2.7 Front Panel Connectors (FP1) ................................................................ 15
2.8 H/W Monitor/Watchdog Timer................................................................. 16
2.8.1 H/W Monitor Alarm (JOBS1)....................................................... 16
2.8.2 Watchdog Timer (JWDT1) .......................................................... 16
2.9 LAN Ports (LAN1 & LAN2)...................................................................... 17
Table 2.1: LAN LED Indicators .................................................. 17
2.10 High Definition Audio Module Interface (HDAUD1)................................. 18
2.11 GPIO Header (GPIO1) ............................................................................ 18
2.12 Case Open Connector (JCASE1) ........................................................... 19
2.13 Front Panel LAN Indicator Connector (LANLED1).................................. 20
Table 2.2: LAN LED Indicators .................................................. 20
2.14 Serial ATA Interface (SATA0~SATA3).................................................... 21
2.15 LPC Extension Interface (LPC2)............................................................. 21

PCE-3032/4132 User Manual viii
2.16 12/5V Power Connector (PWR1) ............................................................ 22
Chapter 3 AMI BIOS Setup................................. 23
3.1 Introduction ............................................................................................. 24
Figure 3.1 Setup Program Initial Screen ................................... 24
3.2 Entering Setup ........................................................................................ 25
3.2.1 Main Setup.................................................................................. 25
Figure 3.2 Main Setup Screen................................................... 25
3.2.2 Advanced BIOS Features Setup................................................. 26
Figure 3.3 Advanced BIOS Features Setup .............................. 26
Figure 3.4 RC ACPI Settings..................................................... 27
Figure 3.5 CPU Configuration ................................................... 28
Figure 3.6 Power & Performance .............................................. 30
Figure 3.7 PCH-FW Configuration............................................. 30
Figure 3.8 Trusted Computing................................................... 31
Figure 3.9 ACPI Settings ........................................................... 32
Figure 3.10SMART Settings....................................................... 33
Figure 3.11Super IO Configuration............................................. 34
Figure 3.12HW Monitor .............................................................. 36
Figure 3.13S5 RTC Wake Settings ............................................ 37
Figure 3.14Serial Port Console Redirection ............................... 38
Figure 3.15Intel TXT Information................................................ 39
Figure 3.16USB Configuration.................................................... 41
Figure 3.17Network Stack Configuration.................................... 42
Figure 3.18CSM Configuration ................................................... 43
Figure 3.19NVME Configuration................................................. 44
3.2.3 Chipset........................................................................................ 44
Figure 3.20Chipset ..................................................................... 44
Figure 3.21System Agent (SA) Configuration ............................ 45
Figure 3.22PEG Port Configuration............................................ 47
Figure 3.23Memory Information ................................................. 48
Figure 3.24PCH IO Configuration............................................... 49
Figure 3.25PCI Express Configuration ....................................... 50
Figure 3.26USB Configuration.................................................... 51
Figure 3.27PCH Azalia Configuration......................................... 52
3.2.4 Security....................................................................................... 53
Figure 3.28Security .................................................................... 53
3.2.5 Boot ............................................................................................ 54
Figure 3.29 Boot ......................................................................... 54
3.2.6 Save & Exit ................................................................................. 55
Figure 3.30Save & Exit............................................................... 55
Chapter 4 Value-Added Software Services ...... 57
4.1 Value-Added Software Services ............................................................. 58
4.1.1 Software API............................................................................... 58
Chapter 5 Chipset Software Installation Utility 59
5.1 Before You Begin.................................................................................... 60
5.2 Introduction ............................................................................................. 60
5.3 Windows 10 Driver Setup ....................................................................... 61
Chapter 6 Integrated Graphic Device Setup .... 63
6.1 Introduction ............................................................................................. 64

ix PCE-3032/4132 User Manual
6.2 Windows 10 Driver Setup........................................................................ 64
Chapter 7 LAN Configuration.............................65
7.1 Introduction ............................................................................................. 66
7.2 Installation ............................................................................................... 66
7.3 Windows 10 Driver Setup (LAN) ............................................................. 66
Chapter 8 Intel ME...............................................67
8.1 Introduction ............................................................................................. 68
8.2 Installation ............................................................................................... 68
Chapter 9 SATA RAID Setup ..............................69
9.1 Introduction ............................................................................................. 70
9.2 SATA RAID Driver and Utility Setup ....................................................... 70
Appendix A Programming the Watchdog Timer..71
A.1 Introduction ............................................................................................. 72
A.1.1 Watchdog Timer Overview.......................................................... 72
A.1.2 Programming the Watchdog Timer ............................................. 72
Table A.1: Watchdog Timer Registers ....................................... 73
A.1.3 Example Program ....................................................................... 74
Appendix B I/O Pin Assignments..........................79
B.1 VGA Connector (VGA1).......................................................................... 80
Table B.1: VGA Connector (VGA1) ........................................... 80
B.2 RS 232 Serial Port (COM12)................................................................... 81
Table B.2: RS-232 Serial Port (COM12).................................... 81
B.3 USB 3.0 Header (USB3H1)..................................................................... 82
Table B.3: USB 3.0 Header (USB23~USB89) ........................... 82
B.4 PS/2 Keyboard/Mouse Connector (KBMS1) ........................................... 82
Table B.4: PS/2 Keyboard/Mouse Connector (KBMS1) ............ 82
B.5 CPU Fan Power Connector (CPUFAN1) ................................................ 83
Table B.5: CPU Fan Power Connector (CPUFAN1).................. 83
B.6 Front Panel Connector (FP1) .................................................................. 83
Table B.6: Front Panel Connector (FP1) ................................... 83
B.7 High-definition Audio Link Connector (HDAUD1).................................... 84
Table B.7: High-definition Audio Link Connector (HDAUD1) ..... 84
B.8 LAN1 and LAN2 LED Connector (LANLED1) ......................................... 84
Table B.8: LAN1 and LAN2 LED Connector (LANLED1)........... 84
B.9 GPIO Header (GPIO1) ............................................................................ 85
Table B.9: GPIO Header (GPIO1) ............................................. 85
B.10 JWDT1 and JOBS1................................................................................. 85
Table B.10:JWDT1 and JOBS1 .................................................. 85
B.11 JCASE1................................................................................................... 86
Table B.11:JCASE1 .................................................................... 86
B.12 LPC2 ....................................................................................................... 86
Table B.12:LPC2......................................................................... 86
B.13 PWR1...................................................................................................... 87
Table B.13:PWR1 ....................................................................... 87
B.14 DP1, DVI1 ............................................................................................... 87
Table B.14:DP1, DVI1................................................................. 87

PCE-3032/4132 User Manual x
B.15 Fixed I/O Ranges Decoded by Intel PCH ............................................... 88
Table B.15:Fixed I/O Ranges Decoded by PCH......................... 88
B.16 System I/O Ports..................................................................................... 89
Table B.16:System I/O Ports ...................................................... 89
B.17 Interrupt Assignments ............................................................................. 90
Table B.17:Interrupt Assignments .............................................. 90
B.18 1 MB Memory Map.................................................................................. 90
Table B.18:1 MB Memory Map ................................................... 90
Appendix C Programming the GPIO .................... 91
C.1 Supported GPIO Register ....................................................................... 92
C.2 GPIO Registers....................................................................................... 92
C.3 GPIO Example Program-1 ...................................................................... 92

Chapter 1
1Hardware
Configuration

PCE-3032/4132 User Manual 2
1.1 Introduction
PCE-3032/4132 is a PICMG 1.3 half-size system host board which is designed with
Intel® H420E (PCE-3032) or W480E (PCE-4132) PCH for industrial applications that
14nm manufacturing technology, LGA1200 socket Intel® Xeon or Core™ i7/i5/i3,
Pentium® and Celeron® processors that integrate memory and graphic controllers
and supports DDR4 2933 SDRAM up to 64 GB. With advanced computing technol-
ogy, PCE-3032/4132 is the best high performance compact system solutions.
PCE-3032/4132 performs excellent graphic capability through its integrated Intel®
HD Graphics core. With this, PCE-3032/4132 provides strong 2D/3D graphic pro-
cessing power without an additional graphic card to save extra cost, power consump-
tion and thermal integration effort. Besides, PCE-3032/4132 supports various display
interfaces to enhance flexibility for system integrators.
PCE-3032/4132 also has rich expansion interfaces which support Advantech PCE-
3BXX and 4BXX backplanes to offer both PCI and PCIe lanes. This fulfills different
applications, such as manufacturing automation, factory automation, automatic opti-
cal inspection, and medical equipment.
In addition, PCE-3032/4132 provides new SATA Gen3 (600MB/sec) ports, satisfy
high data applications, like storage and data management center. PCE-4132's SATA
ports support software RAID 0, 1, 5, 10 as a cost-effective and reliable data solution.
USB 3.0 ports reach 5 Gbps high data rates and RS-232. RS-422,RS-485 and paral-
lel ports are for industrial control applications. With flexible I/O interfaces, PCE-3032/
4132 can be an excellent, graphic or I/O processing platform with outstanding perfor-
mance and exceptional features. They are also the most ideal computing cores for
advanced compact-sized industrial next generation applications.
1.2 Features & Benefits
Processor support: Intel 10th generation family processors with the latest
14nm lithography.
DDR4 2666/2933 up to 64 GB: DDR4 provides up to 50 percent increased per-
formance and bandwidth while saving up to 40 percent power.
Storage: Support SATA 3.0 ports with SW raid 0, 1, 5, 10 support.
High Performance I/O capability: Provides high transfer data performance
interface; USB 3.0 data transfer rate is 5 Gbps which is 10 times faster than
USB2.0.
PCIe architecture: Processor support 16 links of PCI Express generation 3.0
and PCH support 4 links of PCI Express generation 3.0 to PICMG1.3 back-
planes.
SUSI API: Support SUSIAccess and Intelligent system module for remote man-
agement.

3 PCE-3032/4132 User Manual
Chapter 1 Hardware Configuration
1.3 Specifications
1.3.1 System
CPU: LGA1200-socket Core i9/i7/i5/i3, Pentium and Xeon W-1200 series pro-
cessors.
L2 Cache: Please refer to CPU specification for detailed information.
BIOS: (PCE-3032) 128Mb SPI; (PCE-4132) 256Mb SPI.
System Chipset: Intel W480E (PCE-4132); Intel H420E (PCE-3032).
SATA hard disk drive interface: PCE-3032 supports three SATA 3.0 ports, and
PCE-4132 supports four SATA 3.0 ports.
1.3.2 Memory
RAM:
–PCE-4132: Up to 64 GB in two 260-pin SO-DIMM sockets. Supports dual-
channel DDR4 2666/2933 SDRAM WITH or WITHOUT ECC function.
–PCE-3032: Up to 64 GB in two 260-pin SO-DIMM sockets. Supports dual-
channel DDR4 2666/2933 SDRAM WITHOUT ECC function.
1.3.3 Input/Output
PCIe bus: One PCIe x16 or Two PCIe x8 from CPU and One PCIe x4 from
PCH.
Serial ports: Two RS-232 serial ports.
USB port: 6 x USB 2.0 (480Mbps) and 4 x USB 3.0
LPC: One LPC connector to support optional TPM (PCA-TPM-00B1E), COM-
232 (PCA-COM232-00A1E), COM-422/485 (PCA-COM485-00A1E) modules.
GPIO: Supports 8-bit GPIO from super I/O for general purpose control applica-
tion.
1.3.4 Graphics
Controller: Intel® HD Graphics embedded in the processor.
Display memory: Shared memory is subject to OS (install 2 GB or above mem-
ory for basic system configuration).
CRT: Up to 2048x1152 @ 60 Hz.
DVI-D: Up to 1920X1200 @60Hz.
Other display: Supports VGA + Display Port. Display type depends on optional
stack board.
PCI express x16/x8 slot on the backplane: An external graphic card can be
installed in the PCIe x16 /x8 slot for high 2D/3D graphics capability.
Note! PCE-3032/4132 do NOT support PATA(IDE) interface.
Only PCE-4132 supports Intel Xeon processors.
Note! Due to the inherent limitations of the PC architecture, the system may
not fully detect the exact capacity of RAM installed.
Please select Intel ECC supported processor to enable ECC function.

PCE-3032/4132 User Manual 4
1.3.5 Ethernet LAN
Supports single/dual 10/100/1000 Mbps Ethernet port(s) via the dedicated PCI
Express x1 bus which provides 500 MB/s data transmission rate.
Controller:
–LAN 1: Intel® I211AT (PCE-3032) or I210AT (PCE-4132).
–LAN 2: Intel® I211AT(PCE-3032) or I210AT (PCE-4132).
1.3.6 Industrial Features
Watchdog timer: Can generate a system reset. The watchdog timer is pro-
grammable, with each unit equal to one second or one minute (255 levels).
1.3.7 Mechanical and Environmental Specifications
Operating temperature: 0 ~ 60° C (32 ~ 140° F, depending on CPU and ther-
mal solution)
Storage temperature: -40 ~ 85° C (-40 ~ 185° F)
Operating humidity: 40° C @ 85% RH, non-Condensing
Non-operating humidity: 60° C @ 95% RH, non-Condensing
Power supply voltage: +3.3 V, +5 V, +12 V, +5 VSB
Board size: 167.64 x126.39 mm (6.6" x 4.98")
Board weight: 0.33 kg (Weight of board)

5 PCE-3032/4132 User Manual
Chapter 1 Hardware Configuration
1.4 Jumpers and Connectors
Connectors on the PCE-3032/4132 single host board link it to external devices such
as hard disk drives and a keyboard. In addition, the board has a number of jumpers
used to configure your system for your application.
The tables below list the function of each of jumpers and connectors. Later sections
in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for
connecting external devices to your motherboard.
Table 1.1: Jumper List
Label Function
JCMOS1 CMOS clear
JME1 Enable ME
JWDT1 JOBS1 Watchdog timer output selection and HW monitor alarm
Table 1.2: Connectors
Label Function
LAN1 Intel I211AT (PCE-3032); Intel I210AT (PCE-4132)
LAN2 Intel I211AT (PCE-3032); Intel I210AT (PCE-4132)
VGA1 VGA connector
KBMS1 PS/2 keyboard and mouse connector
COM12 Serial port: COM1 (RS-232), and COM2 (RS-232)
FP1 HDD LED, power LED, SNMP SM_Bus, reset, power on/off
JCASE1 Case Open
CPUFAN1 CPU FAN connector (4-pin)
LANLED1 LAN1/2 LED extension connector
HDAUD1 HD audio extension module connector
USB3C1, USB3C2 USB 3.0 port 1,2 on rear I/O
USB3H1 USB 3.0 port 3, 4 with box header
USB2A1 USB 2.0 port 2 on rear I/O
USB2H1, USB2H2 USB 2.0 port 3-6 with box header
SATA0 Serial ATA0 (3.0)
SATA1 Serial ATA1 (3.0)
SATA2 Serial ATA2 (3.0)
SATA3 Serial ATA3 (PCE-4132: 3.0)
CPU1 CPU Socket
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
GPIO1 GPIO pin header (SMD pitch-2.0 mm)
LPC2 COM port module expansion pin-header
PWR1 12 V, 5 V, power connector
DVI1 Pin header to DVI connector (P/N: 1700021831-01)
DP1 Display pin header to stack board
(Display type depends on optional stack board)
EXPCIE1 Mini PCIe pin header to stack board
MINIPCIE MSATA M-SATA (default) or mini-PCIe connector (optional for PCE-4132)

PCE-3032/4132 User Manual 6
1.5 Board Layout: Jumper and Connector
Locations
Figure 1.1 Jumper and Connector Locations
PWR1
DP2
CPU
DIMMA1
DIMMB1 USB3H1
SATA0-3
FP1
USB2H2
USB2A1
USB2H1
CPUFAN1
COM12
JCASE1
JWDT1-JOBS1 LANLED
USB2C1
USB3C1
LPC2
USB3C2
LAN1
GPIO1
PCH
HDAUDIO1
VGA

7 PCE-3032/4132 User Manual
Chapter 1 Hardware Configuration
1.6 Block Diagram
Figure 1.2 PCE-3032 Block Diagram
Figure 1.3 PCE-4132 Block Diagram

PCE-3032/4132 User Manual 8
1.7 Safety Precautions
1.8 Jumper Settings
This section provides instructions on how to configure your motherboard by setting
the jumpers. It also includes the motherboard’s default settings and your options for
each jumper.
1.8.1 How to Set Jumpers
You can configure your motherboard to match the needs of your application by set-
ting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2 and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set-
ting jumpers.
Warning! Always completely disconnect the power cord from your chassis when-
ever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sud-
den power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to static
electrical discharges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
Caution! The computer is provided with a battery-powered Real-time Clock.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to manufacturer's instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.

9 PCE-3032/4132 User Manual
Chapter 1 Hardware Configuration
1.8.2 BIOS (JCMOS1)
PCE-3032/4132 CPU card contains a jumper that can erase BIOS CMOS data and
reset the system BIOS information. Normally this jumper should be set with pins 1-2
closed. If you want to reset those data, set JCMOS1 to 2-3 closed for just a few sec-
onds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS to its last status or default setting.
1.8.3 ME Enable (JME1)
PCE-3032/4132 CPU card contains a jumper that can enable ME data. Normally this
jumper should be set with pins 1-2 closed, then you can see ME information shows in
BIOS menu. If you want to disable ME temporarily for firmware update, set JME1 to
2-3 closed.
Table 1.3: Clear BIOS CMOS (JCMOS1)
Function Jumper Setting
*Keep BIOS CMOS data
Clear BIOS CMOS data
* default setting
1-2 closed
1
2-3 closed
1
Table 1.4: JCMOS1/JME1: Clear CMOS/ME FW Update
Function Jumper Setting
* ME enable
ME disable
* default setting
1-2 closed
1
2-3 closed
1

PCE-3032/4132 User Manual 10
1.8.4 Watchdog Timer Output (JWDT1) and Hardware Monitor
Alarm (JOBS1)
PCE-3032/4132 contains a watchdog timer that will reset the CPU in the event the
CPU stops processing. This feature means PCE-3032/4132 will recover from a soft-
ware failure or an EMI problem. The JWDT1 jumper settings control the outcome of
what the computer will do in the event the watchdog timer is tripped.
PCE-3032/4132 also provide jumper: JOBS1 to enable or disable hardware monitor
alarm.
1.9 System Memory
PCE-3032/4132 has two 260-pin memory sockets for DDR4 2666/2933 MHz memory
modules with maximum capacity of 64 GB. (Maximum 32 GB for each DIMM)
Table 1.5: Watch Dog Timer (JWDT1) and Hardware Monitor Alarm
(JOBS1)
Function Jumper Setting
*Enable watch dog timer
*Enable hardware monitor alarm
* default setting
3
1 5
2-3 closed
3
1 5
4-5 closed
Note! Both PCE-3032 and PCE-4132 do NOT support registered DIMMs
(RDIMMs).