Advantech PCE-7131 User manual

User Manual
PCE-7131/5131/5031
LGA1151
Intel® Core™ i7/i5/i3/Pentium®/
Xeon®PICMG 1.3 Single Host
Board with VGA/DVI-D/M.2/
(ECC)DDR4 U-DIMM/SATA3.0/
USB3.0/GbE

PCE-7131/5131/5031 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
AMIBIOS is a trademark of American Megatrends Inc.
Intel®, Core™i7/i5/i3, Pentium®and Xeon are trademarks of Intel®Corporation.
Nuvoton is a trademark of Nuvoton Technology Corp.
All other product names or trademarks are the properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No.2001513100 Edition 1
April 2019

iii PCE-7131/5131/5031 User Manual
Declaration of Conformity
FCC Class A
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.

PCE-7131/5131/5031 User Manual iv
Backplane Support Matrix Table
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the PCE-7131/5131/5031
mechanically and electrically before shipment. It should be free of marks and
scratches and in perfect working order upon receipt. As you unpack the PCE-7131/
5131/5031, check it for signs of shipping damage. (For example, damaged box,
scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our
service department or your local sales representative immediately. Also notify the
carrier. Retain the shipping carton and packing material for inspection by the carrier.
After inspection, we will make arrangements to repair or replace the unit.
Backplane
Model PCE-5XXX PCE-7XXX
PCE-5131/5031 Yes -
PCE-7131 Yes Yes (Except PCE-7B10-04A1E)
Note! If SBC is used on different backplanes which has different PCIe configu-
ration. Below message would be showed on first time power on, and
user has to turn off AC power and then turn on for PCIe re-configuration.
Caution! PCIe configuration error! Please turn off AC power before re-configura-
tion.
1 PCE-7131/5131/5031 PICMG 1.3 Single Host Board
1 PCE-7131/5131/5031 startup manual
1 CD with utility
2 Serial ATA HDD data cable P/N: 1700003194
1 Serial ATA HDD power cable P/N: 1700022749-11
1 COM + printer ports cable kit P/N: 1700022749-11
1 2-port USB cable kit P/N: 1700002204
Keyboard and mouse Y cable P/N: 1700060202
1 jumper package P/N: 9689000068
1 warranty card

v PCE-7131/5131/5031 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ...............................................................................................2
1.2 Features & Benefits...................................................................................2
1.3 Specifications............................................................................................3
1.3.1 System..........................................................................................3
1.3.2 Memory.........................................................................................3
1.3.3 Input/Output..................................................................................3
1.3.4 Graphics........................................................................................4
1.3.5 Ethernet LAN ................................................................................4
1.3.6 Industrial features .........................................................................4
1.3.7 Mechanical and environmental specifications...............................4
1.4 Jumpers and Connectors..........................................................................5
Table 1.1: Jumpers......................................................................5
Table 1.2: Connectors.................................................................5
1.5 Board Layout: Jumper and Connector Locations......................................6
Figure 1.1 Jumper and connector locations.................................6
1.6 Block Diagram...........................................................................................7
Figure 1.2 PCE-7131 block diagram............................................7
Figure 1.3 PCE-5131 block diagram............................................7
Figure 1.4 PCE-5031 block diagram............................................8
1.7 Safety Precautions....................................................................................8
1.8 Jumper Settings ........................................................................................9
1.8.1 How to set jumpers.......................................................................9
1.8.2 BIOS CMOS (JCMOS1)................................................................9
Table 1.3: JCMOS1/JME1: clear CMOS/ME data.......................9
1.8.3 Watchdog timer output (JWDT1) ..................................................9
Table 1.4: Watchdog timer output (JWDT1)................................9
Table 1.5: H/W monitor alarm (JOBS1)....................................10
1.9 System Memory ......................................................................................10
1.10 Memory Installation Procedures..............................................................10
1.11 Cache Memory........................................................................................10
1.12 Processor Installation..............................................................................11
1.13 Processor Cooler Installation..................................................................13
Chapter 2 Connecting Peripherals ....................15
2.1 Introduction .............................................................................................16
2.2 Parallel Port (LPT1).................................................................................16
2.3 USB Ports (USB12, USB3, USB4, USB56, USB78)...............................16
2.4 VGA Connectors (VGA1) ........................................................................17
2.5 Serial Ports (COM1 & COM2).................................................................17
2.6 PS/2 Keyboard and Mouse Connector (KBMS1/KBMS2).......................18
2.7 CPU and System Fan Connectors (CPUFAN1 and SYSFAN1) .............18
2.8 Front Panel Connectors (JFP1, JFP2 & JFP3).......................................19
2.8.1 Power LED and keyboard lock (JFP3)........................................19
Table 2.1: PS/2 or ATX power supply LED status.....................19
2.8.2 External speaker (JFP2).............................................................19
2.8.3 Reset connector (JFP1)..............................................................19
2.8.4 HDD LED connector (JFP2)........................................................20
2.8.5 ATX soft power switch (JFP1).....................................................20
2.9 H/W Monitor/Watchdog Timer/Infrared ...................................................21
2.9.1 H/W monitor alarm (JOBS1) .......................................................21
2.9.2 Watchdog timer (JWDT1) ...........................................................21
2.9.3 Infrared interface (JIR1)..............................................................21

PCE-7131/5131/5031 User Manual vi
2.10 LAN Ports (LAN1 & LAN2) and Front Panel LAN Indicator Connector
(LANLED1).............................................................................................. 22
Table 2.2: LAN LED Indicators.................................................. 22
2.11 High Definition Audio Module Interface (HDAUD1) ................................ 23
2.12 GPIO Header (GPIO1)............................................................................ 23
2.13 Case Open Connector (JCASE1 and JCASEOP_SW1)......................... 24
Figure 2.1 Case Open Jumper Locations.................................. 24
Table 2.3: Case open mode Jumper......................................... 24
Figure 2.2 Case Open Warning in BIOS Menu ......................... 25
2.14 Serial ATA Interface (SATA1~SATA5).................................................... 25
2.15 LPC Extension Interface (LPC1)............................................................. 26
Chapter 3 AMI BIOS Setup................................. 27
3.1 Introduction............................................................................................. 28
Figure 3.1 Setup program initial screen..................................... 28
3.2 Entering Setup........................................................................................ 29
3.2.1 Main Setup.................................................................................. 29
Figure 3.2 Main setup screen.................................................... 29
3.2.2 Advanced BIOS Features Setup................................................. 30
Figure 3.3 Advanced BIOS features setup screen.................... 30
Figure 3.4 Trust Computing....................................................... 31
Figure 3.5 ACPI Settings........................................................... 32
Figure 3.6 AMT Configuration ................................................... 33
Figure 3.7 Firmware Update Configuration ............................... 34
Figure 3.8 Smart Setting............................................................ 35
Figure 3.9 Super IO Configuration............................................. 36
Figure 3.10Serial Port 1 or 2 Configuration................................ 36
Figure 3.11Parallel Configuration............................................... 37
Figure 3.12PC Health Status...................................................... 38
Figure 3.13S5 RTC configuration............................................... 39
Figure 3.14Serial Port console redirection ................................. 40
Figure 3.15CPU Configuration ................................................... 41
Figure 3.16Platform Misc Configuration..................................... 42
Figure 3.17SATA Configuration.................................................. 43
Figure 3.18PCI Subsystem Settings........................................... 44
Figure 3.19PCI Express Settings ............................................... 45
Figure 3.20USB Configuration.................................................... 46
3.2.3 Chipset........................................................................................ 47
Figure 3.21Chipset ..................................................................... 47
Figure 3.22System Agent (SA) Configuration ............................ 47
Figure 3.23Graphics Configuration............................................. 49
Figure 3.24PEG Port Configuration............................................ 50
Figure 3.25Memory Information ................................................. 51
Figure 3.26PCH IO Configuration............................................... 51
Figure 3.27PCI Express Configuration....................................... 52
Figure 3.28USB Configuration.................................................... 53
Figure 3.29PCH Azalia Configuration......................................... 54
3.2.4 Security....................................................................................... 55
Figure 3.30Security .................................................................... 55
3.2.5 Boot ............................................................................................ 56
Figure 3.31 Boot......................................................................... 56
3.2.6 Save & Exit................................................................................. 57
Figure 3.32Save & Exit............................................................... 57
Chapter 4 Value-Added Software Services......59
4.1 Value-Added Software Services............................................................. 60
4.1.1 Software API............................................................................... 60

vii PCE-7131/5131/5031 User Manual
4.1.2 Software Utility............................................................................61
Chapter 5 Chipset Software Installation Utility 63
5.1 Before You Begin....................................................................................64
5.2 Introduction .............................................................................................64
5.3 Windows 10 Driver Setup........................................................................64
Chapter 6 Integrated Graphic Device Setup.....65
6.1 Introduction .............................................................................................66
6.2 Windows 10 Driver Setup........................................................................66
Chapter 7 LAN Configuration.............................67
7.1 Introduction .............................................................................................68
7.2 Installation...............................................................................................68
7.3 Windows 10 Driver Setup (LAN) .............................................................68
Chapter 8 Intel ME...............................................69
8.1 Introduction .............................................................................................70
8.2 Installation...............................................................................................70
Chapter 9 Intel USB 3.0.......................................71
9.1 Introduction .............................................................................................72
9.2 Installation...............................................................................................72
Chapter 10 SATA RAID Setup..............................73
10.1 Introduction .............................................................................................74
10.2 SATA RAID Driver and Utility Setup .......................................................74
Appendix A Programming the Watchdog Timer..75
A.1 Introduction .............................................................................................76
A.1.1 Watchdog timer overview............................................................76
A.1.2 Programming the watchdog timer...............................................76
Table A.1: Watchdog timer registers..........................................77
A.1.3 Example program........................................................................78
Appendix B I/O Pin Assignments..........................83
B.1 Parallel Port Connector (LPT1)...............................................................84
Table B.1: Parallel port connector (LPT1)..................................84
B.2 VGA Connector (VGA1)..........................................................................84
Table B.2: VGA connector (VGA1)............................................84
B.3 RS 232 Serial Port (COM12)...................................................................85
Table B.3: RS-232 serial port (COM2).......................................85
B.4 USB 2.0 Header (USB56 & 910).............................................................85
Table B.4: USB Header (USB56 & 910)....................................85
B.5 USB3.0 Header (USB12) ........................................................................86

PCE-7131/5131/5031 User Manual viii
Table B.5: USB 3.0 Header (USB12) ........................................ 86
B.6 PS/2 Keyboard/Mouse Connector (KBMS1)........................................... 86
Table B.6: PS/2 keyboard/mouse connector (KBMS1).............. 86
B.7 External Keyboard Connector (KBMS2) ................................................. 87
Table B.7: External keyboard connector (KBMS2).................... 87
B.8 CPU and System Fan Power Connector (CPUFAN1 /SYSFAN1).......... 87
Table B.8: CPU and system fan power connector (CPUFAN1). 87
B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY
LOCK)..................................................................................................... 87
Table B.9: Power LED and keyboard lock connector (JFP3 /
PWR_LED & KEY LOCK) ........................................ 87
B.10 External Speaker Connector (JFP2 / SPEAKER)................................... 88
Table B.10:External speaker connector (JFP2 / SPEAKER)...... 88
B.11 Reset Connector (JFP1 / RESET) .......................................................... 88
Table B.11:Reset connector (JFP1 / RESET) ............................ 88
B.12 HDD LED (JFP2 / HDDLED)................................................................... 88
Table B.12:HDD LED (JFP2 / HDDLED).................................... 88
B.13 ATX Soft Power Switch (JFP1 / PWR_SW)............................................ 89
Table B.13:ATX soft power switch (JFP1 / PWR_SW)............... 89
B.14 Hi-definition Audio Link Connector (HDAUD1) ....................................... 89
Table B.14:Hi-definition audio link connector (HDAUD1)........... 89
B.15 SM Bus Connector (JFP2 / SNMP)......................................................... 89
Table B.15:SM bus connector (JFP2 / SNMP)........................... 89
B.16 LAN1 and LAN2 LED Connector (LANLED1)......................................... 90
Table B.16:LAN1 and LAN2 LED connector (LANLED1)........... 90
B.17 GPIO Header (GPIO1)............................................................................ 90
Table B.17:GPIO header (GPIO1).............................................. 90
B.18 Fixed I/O Ranges Decoded by Intel PCH ............................................... 91
Table B.18:Fixed I/O Ranges Decoded by PCH......................... 91
B.19 System I/O Ports..................................................................................... 92
Table B.19:System I/O Ports...................................................... 92
B.20 Interrupt Assignments............................................................................. 92
Table B.20:Interrupt Assignments .............................................. 92
B.21 1 MB Memory Map.................................................................................. 93
Table B.21:1 MB memory map................................................... 93
B.22 PCI Bus Map........................................................................................... 93
Table B.22:PCI Bus Map............................................................ 93
Appendix C Programming the GPIO....................95
C.1 Supported GPIO Register....................................................................... 96
C.2 GPIO Registers....................................................................................... 96
C.3 GPIO Example Program-1...................................................................... 96

Chapter 1
1Hardware
Configuration

PCE-7131/5131/5031 User Manual 2
1.1 Introduction
PCE-7131/5131/5031 is a PICMG 1.3 form-factor single host board which is
designed with Intel® C246 (PCE-7131), Q370 (PCE-5131), and H310 (PCE-5031)
PCH for industrial applications that need high computing power and strong I/O capa-
bility. PCE-7131/5131/5031 supports 14nm manufacturing technology, LGA1151
socket Intel® Core™ i7/i5/i3, Pentium® and Xeon™ processors that integrate mem-
ory and graphic controllers, and support for DDR4 2666 SDRAM up to 32 GB. Within
advanced computing technology, PCE-7131/5131/5031 is suitable for processor hun-
gry industrial applications.
PCE-7131/5131/5031 offers excellent graphics capability with its integrated Intel®
HD graphics core with a minimum 1 GB shared memory (requires a minimum 2GB
system memory). With this, PCE-7131/5131/5031 provides strong 2D/3D graphics
processing power without an additional graphic card to save extra cost, power con-
sumption and thermal integration effort.
PCE-7131/5131/5031 features rich I/O interface: M.2 which can support M.2 (2280)
type-M for SATA3.0 (6 Gb/s) devices, SATA 3.0 ports with SW raid 0, 1, 5, 10 (PCE-
5031 do not support RAID), integrated USB 3.0 controllers @ 5Gbps, 2 x RS-232
serial COM ports. Moreover, PCE-7131/5131/5031 can support Advantech PCE-
5BXX and PCE-7BXX (PCE-7131 only) series backplanes offering various combina-
tions of expansion such as PCI, PCI-X and PCIe slots. With flexible I/O and graphic
expansibility, PCE-7131/5131/5031 is an excellent, cost effective graphic or I/O ori-
ented workstation class hardware platform. With outstanding performance and
exceptional features, PCE-7131/5131/5031 is the ideal computing platform for
advanced industrial applications.
1.2 Features & Benefits
Processor support: Intel 6th generation family processors with the latest 14nm
lithography.
Memory Capacity: Supports (ECC;C246) DDR4 2666 U-DIMM 16GB per
DIMM up to 32 GB memory capacity. DDR4 provides up to 50% increased per-
formance and bandwidth while saving up to 40% power.
Memory technology: Supports up to 1024M x 8 memory die.
Storage: Support M.2 (2280) type-M SSD module for SATA3.0 interfaces, and
SATA 3.1 ports with SW raid 0, 1, 5, 10 support (PCE-5031 do not support
RAID).
High Performance I/O capability: Provides high transfer data performance
interface; USB 3.0 data transfer rate is 5 Gbps which is 10 times faster than
USB2.0.
PCIe architecture: Processor supports 16 link PCI Express generation 3.0 and
PCH support 4 links of PCI Express generation 3.0 to PICMG1.3 backplanes.
SUSI API: Support SUSIAccess and Intelligent system module for remote man-
agement.

3 PCE-7131/5131/5031 User Manual
Chapter 1 Hardware Configuration
1.3 Specifications
1.3.1 System
CPU: LGA1151-socket Core i7/i5/i3, Pentium and Xeon E series processors
L2 Cache: Please refer to CPU specification for detailed information.
BIOS: AMI SPI BIOS (128 Mb SPI).
System Chipset: Intel C246 (PCE-7131); Intel Q370 (PCE-5131); Intel H310
(PCE-5031)
SATA hard disk drive interface: Five (PCE-7131/5131) or four (PCE-5031)
SATA3 (600MB/s) ports are with blue connector. These interfaces can be
enabled/disabled in the BIOS.
M.2(2280) Type-M: Supports SATA3.0 with x4 links device.
1.3.2 Memory
RAM:
–PCE-7131: Up to 32 GB in two 288-pin DIMM sockets. Supports dual-chan-
nel DDR4 2400/2666 SDRAM WITH or WITHOUT ECC function.
–PCE-5131/5031: Up to 32 GB in two 288-pin DIMM sockets. Supports dual-
channel DDR4 1866/2133 SDRAM WITHOUT ECC function.
1.3.3 Input/Output
PCIe bus: One PCIex16 or Two PCIex8 from CPU and One PCIe x4 from PCH
PCI bus: Four PCI masters to the backplane, 32-bit, 33 MHz PCI 2.2 compliant.
Enhanced parallel port: This EPP/SPP/ECP port can be configured to LPT1,
LPT2, LPT3 or disabled. A standard DB-25 female connector provided.
Serial ports: Two RS-232 serial ports
PS/2 keyboard and mouse connector:
One 6-pin mini-DIN connectors is
located on the mounting bracket for easy connection to a PS/2 keyboard and
mouse via the Y-cable included in the package.
USB port: Supports 7 x USB 2.0 ports with transfer rates up to 480 Mbps. (5
ports are on the CPU card and 4 ports are on the backplane), and 6 USB
3.1(Gen1) ports with transfer rates of up to 5 Gbps, 1 USB 3.1 (Gen2).
LPC: One LPC connector supports Advantech TPM LPC modules.
GPIO: Supports 8-bit GPIO from super I/O for general purpose control applica-
tion.
Note! PCE-7131/5131/5031 does NOT support PATA (IDE) interface.
Only PCE-7131 supports Intel Xeon processors.
Note! A 32-bit OS may not fully detect 4 GB of RAM when 4 GB is installed.
Please select Intel ECC supported processor to enable ECC function.

PCE-7131/5131/5031 User Manual 4
1.3.4 Graphics
Controller: Intel® HD Graphics embedded in the processor.
Display memory: Shared memory is subject to OS (install 2 GB or above mem-
ory for basic system configuration).
CRT: Up to 1920 x 1200 resolution, 60 MHz RAMDAC.
DVI-D: Two DVI-D pin header ports support resolutions up to 1920 x 1200 @ 60
Hz.
Display Port: Supports resolution up to 4096 x 2304 @ 60 Hz, 24bpp.
PCI express x16/x8 slot on the backplane: An external graphic card can be
installed in the PCIe x16 / x8 slot for high 2D/3D graphics capability.
1.3.5 Ethernet LAN
Supports single/dual 10/100/1000 Mbps Ethernet port(s) via the dedicated PCI
Express x1 bus which provides 500 MB/s data transmission rate.
Controller:
–LAN 1: Intel® I219LM (PCE-7131/5131); I219V (PCE-5031)
–LAN 2: Intel® i211AT (PCE-5131/5031); I210AT(PCE-7131)
1.3.6 Industrial features
Watchdog timer: Can generate a system reset. The watchdog timer is pro-
grammable, with each unit equal to one second or one minute (255 levels).
1.3.7 Mechanical and environmental specifications
Operating temperature: 0 ~ 60 °C (32 ~ 140 °F, depending on CPU and ther-
mal solution)
Storage temperature: -40 ~ 85 °C (-40 ~ 185 °F)
Humidity: 20 ~ 95% non-condensing
Power supply voltage: +3.3 V, +5 V, +12 V, +5 VSB
Power consumption: Processor: Intel Core i7-8700; Memory: DDR4 2666
8 GB x 2
Voltage +12 V +5 V +3.3 V
Current 4.30 A 2.15 A 0.69 A
Board size: 338.58 mm (L) x 126.39 mm (W) (13.3" x 4.98")
Board weight: 0.5 kg

5 PCE-7131/5131/5031 User Manual
Chapter 1 Hardware Configuration
1.4 Jumpers and Connectors
Connectors on the PCE-7131/5131/5031 single host board link it to external devices
such as hard disk drives and a keyboard. In addition, the board has a number of
jumpers used to configure your system for your application.
The tables below list the function of each of the board jumpers and connectors. Later
sections in this chapter give instructions on setting jumpers. Chapter 2 gives instruc-
tions for connecting external devices to your motherboard.
Table 1.1: Jumpers
Label Function
JCMOS1 CMOS clear
JME1 Clear ME data
JWDT1 Watchdog timer output selection
JOBS1 Super IO Alarm setting
Table 1.2: Connectors
Label Function
USB3C1 USB3 port1
LAN1 Intel I219LM (PCE-7131/5131); Intel I219V (PCE-5031)
LAN2 Intel I210AT (PCE-7131); Intel I211 (PCE-5131/5031)
VGA1 VGA connector
KBMS1 External PS/2 keyboard and mouse connector
KBMS2 Internal PS/2 keyboard and mouse connector
HDAUD1 Advantech HD audio module expansion pin-header
LPC1 LPC module expansion pin-header
Sysfan1 4 PIN fan power connector for supporting PWM or DC fan
LANLED1 LANLED
USB11 USB port 10
USB45 USB port 4, 5
USB3H2 USB3 port 5, 6
USB3H1 USB3 port 3, 4
USB3H3 USB3 port 7, 8
COM1 RS-232 (9-pin Box Header)
COM2 RS-232 (9-pin Box Header)
LPT1 Parallel port
SATA0 / M.2 SATA port 0
SATA 1~5 SATA Port 1 ~ 5
SPI_CN1 CMOS flash jig pin-header
SPI1 CMOS ROM
DP1 Display port pin-header 1
DP2 Display port pin-header 1
JCMOS1 Clear CMOS
JME1 Clear ME
JFP1 + JFP2 Power Switch / Reset connector / External speaker / SATA HDD LED
connector

PCE-7131/5131/5031 User Manual 6
1.5 Board Layout: Jumper and Connector
Locations
Figure 1.1 Jumper and connector locations
JFP3 (Keyboard
Lock and Power
LED)
Power LED
Suspend: Fast flash (ATX/AT)
System On: ON (ATX/AT)
System Off: OFF (ATX/AT)
CPUFAN1 CPU FAN Power connector
JCASE1 Case Open pin-header
JCASEOP_SW1 Case Open switch for always open or close
BAT1 Button battery socket
BAT2 External battery connector
GPIO1 GPIO pin header (SMD pitch-2.0 mm)
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
1

7 PCE-7131/5131/5031 User Manual
Chapter 1 Hardware Configuration
1.6 Block Diagram
Figure 1.2 PCE-7131 block diagram
Figure 1.3 PCE-5131 block diagram

PCE-7131/5131/5031 User Manual 8
Figure 1.4 PCE-5031 block diagram
1.7 Safety Precautions
Warning! Always completely disconnect the power cord from your chassis when-
ever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sud-
den power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to static
electrical discharges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
Caution! The computer is provided with a battery-powered Real-time Clock.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to manufacturer's instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.

9 PCE-7131/5131/5031 User Manual
Chapter 1 Hardware Configuration
1.8 Jumper Settings
This section provides instructions on how to configure your motherboard by setting
the jumpers. It also includes the motherboard’s default settings and your options for
each jumper.
1.8.1 How to set jumpers
You can configure your motherboard to match the needs of your application by set-
ting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2 and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set-
ting jumpers.
1.8.2 BIOS CMOS (JCMOS1)
The SBC CPU card contains a jumper that can erase BIOS CMOS/ME data and
reset the system BIOS information. Normally this jumper should be set with pins 1-2
closed. If you want to reset those data, set JCMOS1/JME1 to 2-3 closed for just a few
seconds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS/ME to its last status or default setting.
1.8.3 Watchdog timer output (JWDT1)
The SBC contains a watchdog timer that will reset the CPU in the event the CPU
stops processing. This feature means the SBC will recover from a software failure or
an EMI problem. The JWDT1 jumper settings control the outcome of what the com-
puter will do in the event the watchdog timer is tripped.
Table 1.3: JCMOS1/JME1: clear CMOS/ME data
Function Jumper Setting
*Keep BIOS CMOS/ME data
Clear BIOS CMOS/ME data
* default setting
1
1-2 closed
2-3 closed
Table 1.4: Watchdog timer output (JWDT1)
Function Jumper Setting
NC
* Reset
* default setting
2-4 closed
4-6 closed

PCE-7131/5131/5031 User Manual 10
(JOBS1) is a 2-pin connector for setting enable/disable alarm while the on-board
security event acts.
1.9 System Memory
PCE-7131/5131/5031 has two 288-pin memory sockets for (ECC) DDR4 1866/2133
memory modules with maximum capacity of 32GB. (Maximum 16GB for each DIMM)
PCE-7131 supports ECC and non-ECC DDR4 U-DIMM memory modules.
PCE-5131/5031 supports non-ECC DDR4 U-DIMM memory modules.
1.10 Memory Installation Procedures
To install DIMMs, first make sure the two handles of the DIMM socket are in the
“open” position. i.e. the handles lean outward. Slowly slide the DIMM module along
the plastic guides on both ends of the socket. Then press the DIMM module right
down into the socket, until you hear a click. This is when the two handles have auto-
matically locked the memory module into the correct position of the DIMM socket. To
remove the memory module, just push both handles outward, and the memory mod-
ule will be ejected by the mechanism in the socket.
1.11 Cache Memory
L3 memory cache size is subject to each Intel processor and please refer to the Intel
datasheet for detailed information.
Table 1.5: H/W monitor alarm (JOBS1)
Function Jumper Setting
Enabled
Disabled
1-2 closed (Default)
12
1-2 opened
12
Note! PCE-7131/5131/5031 do NOT support registered DIMMs (RDIMMs).
Note! Because PCE-7131/5131 supports Intel Active Management Technol-
ogy 11.0 (AMT11.0) which utilizes some memory space ofchannel 0, it's
suggested that the user should not leave channel 0 DIMM slots
(DIMMA1) empty, or it may cause some system abnormality.

11 PCE-7131/5131/5031 User Manual
Chapter 1 Hardware Configuration
1.12 Processor Installation
The PCE-7131/5131/5031 is designed for Intel® LGA 1151 socket processors.
1. Pull the bar beside the processor socket outward and lift it.
2. Remove the socket protection cap.
Warning! Without a fan or heat sink, the processor will overheat and cause dam-
age to both the processor and the single board computer. To install a
processor, first turn off your system.

PCE-7131/5131/5031 User Manual 12
3. Align the cuts on the processor with the edges of the socket.
4. Replace the socket cap; lower the retainer bar and clip it shut.
5. The finished processor installation.