Advantech ICR-3211 Guide

Start Guide
ICR-3211, ICR-3231
ICR-3232, ICR-3241

Start Guide
Safety Instructions
Please take care to following instructions:
•Use the router in compliance with national and international law and in compliance with
any special or additional restrictions regulating use of the router in the various applica-
tions and environments.
•To avoid possible injury and/or damage to the device, observe the relevant provisions
and standards. Use only the original accessories as recommended. Unauthorized de-
vice or accessory modification, or using accessories that have not been approved can
result in router damage and/or violation of the regulations.
•Unauthorized device or accessory modification or using the accessories that have not
been approved can result in warranty termination.
•Do not open the router.
•Caution! The SIM card can be swallowed by small children.
•When connecting the device to a power supply do not exceed the defined voltage.
•Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture, and high temperature.
•It is recommended that you do not use the router at petrol filling stations. We recommend
observing local restrictions concerning the use of radio-based devices while working with
explosive material for example, at petrol filling stations, or in chemical plants.
•While using the router close to personal medical devices, such as cardiac pacemakers
or hearing aids, proceed with heightened caution.
•Operating the router too close to TV sets, radio receivers, personal computers, or tele-
phones can cause interference.
•It is recommended that you create a copy or backup of the important settings stored in
the memory of the router.
QSG-0006-EN, December 10, 2018 1Released in the Czech Republic

Start Guide
Product Disposal Instructions
The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) direc-
tive was introduced to ensure that electrical/electronic products are recycled us-
ing the best available recovery techniques in order to minimize impact on the en-
vironment. This product contains high quality materials and components which
can be recycled. At the end of it’s life this pro- duct MUST NOT be mixed with
other commercial waste for disposal. The device contains the battery. Remove
the battery from the device before disposal. The battery in the device needs to be disposed
apart accordingly. Check the terms and conditions of your supplier for disposal information.
Open Source Software License
The software in this device uses various pieces of open source software governed by
following licenses:
•GPL versions 2 and 3
•LGPL version 2
•BSD-style licences
•MIT-style licences
The list of components together with complete license texts can be found on the device
itself. See Licenses link at the bottom of the router’s main Web page (General Status) or point
your browser to this address (replace the DEVICE_IP string with real router’s IP address):
https://DEVICE_IP/licenses.cgi
This is a written offer valid for 3 years since the device purchase offering any third party for
a charge no more than cost of physically performing source distribution, a complete machine-
readable copy of the corresponding source code on a flash drive medium. If you are interested
in obtaining the source, please contact us at:
[email protected]
Modifications and debugging of LGPL-linked executables:
The manufacturer of the device hereby grants the right to use debugging techniques (e.g.
decompilation) and making customer modifications of any executable linked with a LGPL li-
brary for own purposes. Note these rights are limited to the customer’s own usage. No further
distribution of such modified executables and no transmission of the information obtained dur-
ing these actions may be done.
QSG-0006-EN, December 10, 2018 2Released in the Czech Republic

Start Guide
First Use
Before applying power to the router, connect the components that you required for your
applications. You cannot operate the router without connected antenna, inserted SIM card,
nor connected power supply. Cross-shaped screwdriver is necessary to insert a SIM card.
If you do not have connected main antenna during operation of the router, the router can
be damaged!
1. Antenna
Use a SMA connector to connect the antennas to the router. The main antenna is con-
nected to the router by screwing on the ANT connector (see Figure below). The second diver-
sity antenna can also be connected to the DIV connector to improve performance.
2. SIM Card
The SIM card readers, for 3 V and 1.8 V SIM cards, are located on the left side panel of the
router. If you intend to use this device to communicate over a cellular network, please place an
activated data-provisioned SIM card with an unblocked PIN into the SIM card reader. Unscrew
the SIM cards cover and push your SIM card into the SIM1 or SIM2 slot until it clicks in place.
QSG-0006-EN, December 10, 2018 3Released in the Czech Republic

Start Guide
Disconnect the router from power supply before handling of the SIM card!
3. Power
The router requires an external DC power supply. The DC voltage required is between
+9 to +36 V DC. The router has built-in protection against reverse polarity without signaling.
Connect the power supply cable to the PWR connector on the front panel of the router (see
Figure below).
QSG-0006-EN, December 10, 2018 4Released in the Czech Republic

Start Guide
4. Ethernet
An Ethernet cable may be connected to the ETH0 connector on the front panel of the router
(see Figure above). By default, the Ethernet port is configured as follows:
Connector Purpose Default Setting
ETH0 LAN port (default)
Connect your laptop or PC to this port to
get a local web-server for device configu-
ration and diagnostics.
DHCP Server
IP Address: 192.168.1.1
NetMask: 255.255.255.0
Configuration
1. Configuring the Device Using the Web Browser
You can access the router for status monitoring, configuration, and administration after
entering the IP address of the router into a Web browser. The default IP address is 192.168.1.1
(netmask 255.255.255.0). Configuration access is allowed for the user "root" with the initial
password "root". Attention, it is necessary to use HTTPS protocol for secure communication
over a network! For a detailed description and examples of the router configurations, see the
Configuration Manual.
User Default Password
root root
After logging on to the device for the first time, we strongly recommend to change
the default password due to security reasons.
2. Configuration Settings via SmartWorx Hub
If your router has been pre-installed with the SmartWorx Hub client, you may configure it
from SmartWorx Hub. Navigate your browser to:
https://hub.bb-smartworx.com
If this is your first time, please register with the site. If not, please login with your username
and password. Once logged in, further assistance can be found here:
https://hub.bb-smartworx.com/Login/Help?HelpFile=bbdms_help.pdf
QSG-0006-EN, December 10, 2018 5Released in the Czech Republic

Start Guide
3. Restoring and Backing up the Router Configuration
After you reset the router, the current configuration is overwritten by the default settings.
We recommend that you back up the router configuration before resetting the device. Refer to
the Configuration Manual for more information.
When the PWR LED starts blinking, it is possible to restore the default configuration of the
router by pressing the Reset button on the panel continuously for more than 4 seconds. Use
a narrow screwdriver or any tool that fits. After releasing the button, the default configuration
is restored and then the router reboots (green PWR LED will be on).
Documentation
User’s Manual, Configuration Manual and other manuals can be found and downloaded
on this web site: www.advantech-bb.cz/download
Hereby, Advantech B+B SmartWorx s.r.o. declares that the radio equipment type
ICR-3231 is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
www.advantech-bb.cz/eudoc
QSG-0006-EN, December 10, 2018 6Released in the Czech Republic