Advantech ARK-5261 Installation and operation manual

ARK-5261 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. ARK-5261 System x 1 P/N: ARK-5261S-J0A1E
(ARK-5261I System x 1 P/N: ARK-5261I-J0A1E)
2. Startup Manual x 1 P/N: 2001526110
3. Driver CD x 1 P/N: 2061526100
4. Warranty Card P/N: 2190000902
5. Wallmount bracket x2 P/N: 1960049826N001
1960049827N001
6. DB37 to DB9 Cable* P/N:* 1700021869-01
Only for ARK-5261I version
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of ARK-5261, please refer
to information on the enclosed CD-ROM (in PDF
format).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
ARK-5261 / ARK-5261I
Intel® Celeron® Processor J1900 Fanless Embedded
BOX PC with PCI/PCIe Expansion and Dual Mobile
HDDs/SSDs
Startup Manual
Processor System
• Intel® Celeron® Processor J1900 up to 2.41 GHz
Memory
• Support daul channel DDR3L (Lower power 1.35V)-1333
Mhz, 2GB per slot without ECC function; Max. capacity is
up to 8GB
Graphics
• Chipset integrated Intel HD Graphic
Serial Ports
• Standard Type:
- 4x RS-232/422/485, selection by BIOS
- Support Auto-flow control
- COM1 & COM2 support 5V/12V power, selection by
Jumper
• Isolation Type:
- 4 x RS-422/485 ports (by DB37 to 4x DB9 cable)
- ESD protection: 15Kv
- Suger production: 2Kv
- Electrical Isolation: 2Kv
Ethernet
• Interface: 10/100/1000 Mbps
• Controller:
LAN1: Intel I211, supports Wake on LAN
LAN2: Intel I211, supports Wake on LAN
Storage
• Internal 2.5” HDD Bay: 2
• m-SATA: 1 (Shared with SATA 2)
Front I/O
• Display: 1 x VGA
• USB: 1 x USB3.0; 4 x USB2.0; 1 x Internal USB2.0
• Serial: 4 x RS-232/422/485 selection by BIOS
• DIO: Support 8-bit GPIO by DB9 Connector
• Parallel port: Support D-sub 25 pin connector
• Keyboard/Mouse: 1 x PS/2 port, support PS/2 mouse
and Keyboard
Power Requirement
• Power Type: AT X / AX
• Power Input Voltage: 9~30 VDC
• Minimum Power Input:9V @ 6.6A ~ 30V @ 2A
• Power Adapter: AC to DC, 65W DC19V/3.4A
Specications Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/default.
aspx
This manual is for the ARK-5261 Series Rev. A1.
Part No. 2001526110
Printed in China
1st Edition
1RYHPEHU2014

2 ARK-5261 Startup Manual
JCOMPWR1/JCOMPWR2: COM1 & 2 Power Selection
Functions Jumper Setting
4-6 RI (Default no power)
3-4 5V Power
4-6 12V Power
PSON1: System AT/ATX Module Selection
Function Jumper Setting
1-2 AT module
2-3 ATX module
The drivers for the ARK-5261 are located on the software
installation CD. Please click through the folder and follow the
on screen instructions to install them.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditons:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Miscellaneous
• LED Indicators: Power, HDD
• Control: Power on/off switch
Environment
• Operating Temperature:}
-10 ~ 60° C with 0.7m/sec air flow: with 2 x Industrial SSD
without PC expansion boards
0 ~ 45° C with 0.7m/sec air flow: with 1 x 2.5” HDD or
mSATA without PC expansion boards
• Storage Temperature: - 40 ~ 85° C (-40 ~185° F)
• Relative Humidity: 95% @ 40° C (non-condensing)
Physical Characteristics
• Dimension (WxHxD): 137 x 189 x 221 mm
• Weight: 4.2 Kg
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
VGA1 VGA connector
LAN 1 Intel I211
LAN 2 Intel I211
USB 1 USB 3.0
PS/2 Keyboard & Mouse connector
COM 12 RS-232/422/485 with Power
COM 34 RS-232/422/485
Isolation
COM* RS-422/485 Isolation COM
DIO1 GPIO Connector
LTP Printer Connector
USB 2345 USB 2.0 port 2,3,4,5
Audio Audio Jack x 2
DC 9~30V2 Power Connector
*Only for Isolation version
Jumpers and Connectors
Jumpers and Connectors (cont.)
Software Installation
Declaration of Conformity
Specications (cont.)

ARK-5261 Startup Manual 3
Memory Installation
Warring: ARK-5261 system already is on-board 4GB
memory inside, if you want to expand to 8GB.
Please connect your sales or agents to order com-
patible memory modules, the part number below:
AQD-SD3L4GN16-SG
4G SO-DDR3-1600 512x8 1.35v SAM
Note: If ARK-5261 use differnet brand of SO-DIMM
memory, the system will be not boot.
COM with Power Jumper Selection
1. Unscrew and remove left side case cover.
2. COM 1 & 2 Power Jumper location and you can be
selection 5V or 12V power based on your device power
required.
HDD Installation
1. Unscrew the HDD door screws
2. Unscrew the HDD tray’s screw.
3. Assemble 2.5’ SATA HDD with four screws on bottom
side fo bracket.
4. Insert the bracket into the housing.
5. Secure the HDD tracy with screw
6. Replace the HDD door and secure with screws.
m-SATA Installation
1. Unscrew 2 screws and remove the top cover.
2. Unscrew and remove top bracket & left side case cover.
Install the m-SATA and secure screw.
3. Replace the left side cover first and top bracket/cover
and secure with screws.
System I/O Interface Simple Maintain Process (cont.)
Simple Maintain Process

4 ARK-5261 Startup Manual
System Dimension
90
137
11
5
189 215
234
90
120
5
240.97
234.07
221
Unit : mm(inch)

ARK-5261快速入门手册 1
安装板卡之前，用户需确认包装中含有下面所列各项：
1. ARK-5261系统 x 1 P/N：ARK-5261S-J0A1E
（ARK-5261I系统 x 1 P/N：ARK-5261I-J0A1E)
2. 快速入门手册 x 1 P/N: 2001526110
3. 驱动光盘 x 1 P/N: 2061526100
4. 质保卡 P/N: 2190000902
5. 壁挂式安装支架 x 2 P/N: 1960049826N001
1960049827N001
6. DB37转DB9电缆* P/N:* 1700021869-01
仅适用于ARK-5261I版本
如果其中任何一项缺失或损坏，请立即与经销商或销售代
表联系。
注1： 关于ARK-5261的详细信息，请参考附带的CD-ROM
光盘（PDF格式）。
注2： 阅读PDF文件需要使用Acrobat Reader。用户可从
以下路径下载Acrobat Reader：get. adobe.com/
reader（Acrobat为Adobe公司的商标）。
ARK-5261 / ARK-5261I 无风扇嵌入式工控机
搭载Intel® Celeron® 处理器J1900，
支持PCI/PCIe扩展和双移动HDD/SSD
快速入门手册
处理器系统
• Intel® Celeron® 处理器J1900，最高可达2.41 GHz
内存
• 支持双通道DDR3L（低功耗1.35V)-1333 Mhz，每个插槽可
支持2 GB（不支持ECC功能）；最大容量可达8 GB
显示
• 芯片组集成Intel HD显卡
串行端口
• 标准类型:
- 4 x RS-232/422/485，可通过BIOS选择
- 支持自动流控制功能
- COM1 & COM2支持5 V/12 V电源,可通过跳线选择
• 隔离类型:
- 4 x RS-422/485端口(通过DB37转4 x DB9电缆)
- ESD保护：15 Kv
- 浪涌保护：2 Kv
- 电隔离：2 Kv
以太网
• 接口:10/100/1000 Mbps
• 控制器:
LAN1：Intel I211，支持网络唤醒
LAN2：Intel I211，支持网络唤醒
存储
• 内置2.5”HDD托架：2
• m-SATA：1（与SATA2共用）
前部I/O
• 显示：1 x VGA
• USB：1 x USB3.0、4 x USB2.0和1 x 内置USB2.0
• 串行端口：4 x RS-232/422/485，可通过BIOS选择
• DIO：通过DB9接口支持8-bit GPIO
• 并行端口：支持D-sub 25针接口
• 键盘/鼠标：1 x PS/2接口，支持PS/2鼠标和键盘
电源要求
• 电源类型：ATX /AT
• 输入电压：9 ~ 30 VDC
• 最小电源输入：9 V @ 6.6 A ~ 30 V @ 2 A
• 电源适配器：AC转DC，65W DC 19 V/3.4 A
其它
• LED指示灯：电源、HDD
• 控制：电源开关
产品规格 包装清单
如需了解有关本产品及研华其它产品的详细信息，请访
问我们的网站：
http://www.advantech.com.cn
http://www.advantech.com.cn/epc
如需技术服务与支持，请访问我们的技术支持网站：
http://support.advantech.com.cn
本手册适用于ARK-5261系列Rev. A1。
料号：2001526110
中国印刷
第一版
2014年11月

2 ARK-5261快速入门手册
JCOMPWR1/JCOMPWR2：COM1 & 2电源选择
功能 跳线设置
4-6 RI（默认未上电）
3-4 5 V电源
4-6 12 V 电源
PSON1：系统AT/ATX模块选择
功能 跳线设置
1-2 AT模式
2-3 AT模式
ARK-5261的驱动保存在软件安装光盘中。请双击文件夹中的
驱动程序并按照屏幕指示进行安装。
注意! 计算机配置了由电池供电的实时时钟电路，如果
电池更换不正确，将有爆炸的危险。因此，只可
以使用制造商推荐的同一种或者同等型号的电池
进行替换。请按照制造商的指示处理旧电池。
本品符合FCC规则第15款限制。操作符合下列两种情况：
1. 此装置不可产生干扰，且
2. 此装置必须接受任何干扰，包括可能导致非预期操作的
干扰。
环境规格
• 工作温度：
-10 ~ 60°C，0.7 m/sec气流（
带2 x 工业级SSD，不带PC扩展板）
0 ~ 45°C，0.7 m/sec气流
（带1 x 2.5”HDD或mSATA，不带PC扩展板）
• 储存温度：- 40 ~ 85°C (-40 ~ 185°F)
• 相对湿度：95% @ 40°C（非凝结）
物理规格
• 尺寸（W x H x D）：137 x 189 x 221 mm
• 重量：4.2 Kg
主板上有很多跳线允许用户配置系统，满足各种不同应用需
求。下表为每个跳线和接口的功能列表。
接口
接口名 功能
VGA1 VGA接口
LAN 1 Intel I211
LAN 2 Intel I211
USB 1 USB 3.0
PS/2 键盘 & 鼠标接口
COM 12 RS-232/422/485（上电）
COM 34 RS-232/422/485
Isolation COM* RS-422/485隔离COM
DIO1 GPI接口
LTP 打印机接口
USB 2345 USB 2.0接口2、3、4、5
Audio 音频插孔 x 2
DC 9 ~ 30V2 电源接口
* 仅适用于隔离版
跳线和接口
跳线和接口（续）
软件安装
符合性声明
产品规格（续）

ARK-5261快速入门手册 3
内存安装
警告： ARK-5261系统已内置板载4 GB内存。如需扩展为8
GB内存，请联系研华销售代表或销售代理订购适用
的内存模块。产品料号如下：
AQD-SD3L4GN16-SG
4G SO-DDR3-1600 512x8 1.35v SAM
注: 若ARK-5261采用了不同品牌的SO-DIMM内存，则系
统将无法启动。
支持电源跳线选择的COM
1. 卸下并移除左侧盖上的螺丝。
2. 在COM 1 & 2的电源跳线位置，根据设备电源需求选择
5 V或12 V。
HDD安装
1. 卸下HDD挡板上的螺丝。
2. 卸下HDD托架上的螺丝。
3. 用四颗螺丝将2.5”SATA HDD固定在支架的底部。
4. 将支架插入到机箱中。
5. 用螺丝将HDD托架固定。
6. 放回HDD挡板并用螺丝固定。
m-SATA安装
1. 卸下两颗螺丝并移除顶盖。
2. 卸下螺丝并移除顶部支架和左侧机箱盖。
安装m-SATA并用螺丝固定。
3. 放回左侧机箱盖和顶部支架/顶盖，并用螺丝固定。
系统I/O接口 简单安装步骤（续）
简单安装步骤

4 ARK-5261快速入门手册
系统尺寸
90
137
11
5
189 215
234
90
120
5
240.97
234.07
221
Unit : mm(inch)