Advantech RIO-3302 User manual

RIO-3302/RIO-3302S
6U CompactPCI TM Rear Transition card

Preface and Table of Contents
PartNo.2002330200 1st Edition
Printed in Taiwan October2001
Copyright Notice
This document is copyrighted, 2001. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from its
use.
Acknowledgements
PICMG™,CompactPCI™ andthe PICMG™,CompactPCI™ logosare
trademarks of the PCI Industrial Computers Manufacturers Group
All other product names or trademarks are properties of their
respective owners.
CE Notification
The MIC-3036, developed by Advantech Co., Ltd., has passed the CE
test for environment specifications when shielded cables are used for
external wiring. We recommend the use of shielded cables.

RIO-3302/RIO-3302S User's Manual
Product warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for
one year from the date of purchase.
This warranty does not apply to any products which have been
repaired or altered by persons other than repair personnel authorized
by Advantech, or which have been subject to misuse, abuse, accident
or improper installation. Advantech assumes no liability under the
terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If
an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service
time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. For
example, CPU speed, Advantech products used, other hardware
and software used, etc. Note anything abnormal and list any on-
screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your
manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandise authorization) number from your dealer. This allows us
to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

Preface and Table of Contents
Packing List
Before installation, ensure that the following materials have been
received:
•OneRIO-3302 (orRIO-3302S) CompactPCI™ reartransition card
•One warranty certificate
•One startup Manual
•One CD disc and manual (in PDF format)
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the RIO-3302
(or RIO-3302S) or any other Advantech products, please visit our
support website at:
•http://www.advantech.com.tw/support
For more information about Advantech's products and sales informa-
tion, please visit:
•http://www.advantech.com

RIO-3302/RIO-3302S User's Manual
Contents
1. General Information ..................................... 1
1.1 Introduction .................................................................................2
1.2 Specification ................................................................................2
1.2.1 SCSI Function.................................................................................2
1.2.2 Standard functions ..........................................................................2
1.2.3 Mechanical and environmental specifications ................................3
1.3.IndicatorandConnectorLocation.................................................4
2. Hardware and drivers Installation .............. 7
2.1 Cardinstallation..........................................................................8
2.1.1 Card Installation and Removal..................................................... 8
2.1.2 Driver installation ......................................................................10
A. Pin Assignments........................................11
A.1 J1connector pin assignment(RIO-3302Sonly) ......................12
A.2 J2connector pin assignment(RIO-3302Sonly) ......................13
A.3 Pin Assignment ........................................................................14
A.3.1 J3 Connector Pin Assignment .....................................................14
A.3.2 J4 Connector Pin Assignment .....................................................15
A.4 RIO-3302SUltra3 SCSIConnectors(CN50)...........................16
A.5 VGADisplayConnector(CN1) .................................................18
A.6 KeyboardandMouseConnnector(CN8,CN9) ..........................18
A.7 COM1andCOM2Serial Port(CN12, CN6) .............................19
A.8 USBConnector(CN3) ...............................................................20
A.9 EthernetRJ-45Connector (CN2,CN4) .....................................20
A.10CompactFlashSocket(CN14) ...................................................21
A.11 Floppy DiskDrive Connector(CN7) .........................................22

Preface and Table of Contents
A.12HardDiskDriveConnector (CN11,CN13) ...............................23
A.13HardDiskDriveConnector (CN10) .........................................24

RIO-3302/RIO-3302S User's Manual
Figures
Figure 1-1: RIO-3302/RIO-3302S connector and jumper locations ............... 4
Figure 2-1: Installing a card into the chassis ................................................ 9

Preface and Table of Contents
Tables
Table 1-1: RIO-3302/RIO-3302S connector and jumper descriptions ........... 5
Table A-1: J1 connector pin assignments .................................................... 12
Table A-2: J2 connector pin assignments .................................................... 13
Table A-3: J3 Connector Pin Assignment ..................................................... 14
Table A-4: J4 Connector Pin Assignment ..................................................... 15
Table A-5: RIO-3302S Ultra3 SCSI connectors ............................................ 16
Table A-6: RIO-3302/RIO-3302S CRT display connector ............................. 18
Table A-7: RIO-3302/RIO-3302S keyboard and mouse connector .............. 18
Table A-8: RIO-3302/RIO-3302S COM1 and COM2 serial port .................... 19
Table A-9: RIO-3302/RIO-3302S USB1 connector ....................................... 20
Table A-10: RIO-3302/RIO-3302S Ethernet RJ-45 connector ...................... 20
Table A-11: RIO-3302/RIO-3302S CompactFlash socket ............................ 21
Table A-12: Floppy Disk Drive Connector ..................................................... 22
Table A-13: Hard Disk Drive Connector ........................................................ 23
Table A-14: Hard Disk Drive Connector ........................................................ 24

Chapter 1 General Information 1
1
General Information
CHAPTER

2RIO-3302/RIO-3302S User's Manual
1.1 Introduction
The RIO-3302/RIO-3302S is a CompactPCI 6U-sized rear transi-
tion board. It provides access to the rear panel for the I/O func-
tion on Advantech’s CompactPCI CPU board.
1.2 Specification
1.2.1 SCSI Function
•Controller: Adaptec AIC-7892TM
•Bus: PCI 64-bit/ 33Mhz
•Channel: single SCSI channel
•Datatransferrate:The data channel DMA engine in the AIC-7892
supports data transfer rates upto 160MB/s on a wide(16-bit) SCSI
usingLVD SCSI I/Os.
•Termination:On-board terminators provided
1.2.2 Standard functions
•Ethernet:Two LAN ports with RJ-45 connectors
•VGAconnector:One DB-15VGA connector
•Serialport:TwoDB-9 RS-232ports
•USBinterface:One USB connectors

Chapter 1 General Information 3
•EIDEinterface: Two connectors forIDE channels(Primary and
Secondary channels)
•FDD interface: Supports one on-board slim-type floppy connector.
•CompactFlash™interface:Supports one on-board CompactFlash™
socket
•Keyboardconnector:One6-pin mini-DIN connectoron rearpanel
•Mouse connector: One6-pin mini-DIN connectoron rear panel
1.2.3 Mechanical and environmental
specifications
•Boardsize:233.35 x80 mm(6U), oneslot (4TE)wide
•Max.powerrequirements:+5 V(4.75~5.25 V) @1A
•Operatingtemperature: 0~ 60º C(32 ~140 ºF)
•Storagetemperature:-20~ 70º C(-4 ~ 158 ºF)
•Humidity(operating andstorage):5 ~ 95%(non-condensing)
•Boardweight:0.8Kg
•Shock:20 G (operating); 50 G (storage/transit)
•Randomvibration:5~500Mhz Operating:1.5GrmsNon-operating:
2Grms

4RIO-3302/RIO-3302S User's Manual
1.3. Indicator and Connector Location
The RIO-3302/RIO-3302S provides jumpers and connectors for
users specific applications.
Figure 1-1: RIO-3302/RIO-3302S connector and jumper locations

Chapter 1 General Information 5
Table 1-1: RIO-3302/RIO-3302S connector and jumper descriptions
Number Function
JP1 CompactFlash master/slave selection
CN1 VGA connector
CN2 LAN 1 connector
CN3 USB 1 connector
CN4 LAN 2 connector
CN6 COM2 port
CN7 Floppy disk connector
CN8 PS/2 keyboard connector
CN9 PS/2 mouse connector
CN10 44-pin IDE channel-1 connector
CN11 IDE channel-1 connector
CN12 COM1 port
CN13 IDE channel-2 connector
CN14 50-pin CompactFlash connector
CN50 SCSI internal connector (RIO-3302S only)
Note:The CompactFlash interface (CN14) uses a primary IDE chan-
nel. Users need to set it as master or slave via jumper JP1 when
another device is connected on the primary IDE channel as

Chapter 2 Hardware and drivers Installation 7
2
Hardware and drivers
Installation
CHAPTER

8RIO-3302/RIO-3302S User's Manual
2.1 Card installation
2.1.1 Card Installation and Removal
The CompactPCITM connectors are firm and rigid, and require careful
handling while plugging and unplugging. Improper installation of a
card can easily damage the backplane of the chassis.
The system card can be installed only in the system slot. Do not insert
the system card into the other slot, or insert a peripheral card into the
system slot. The system slot is marked by a triangle enclosing the slot
number. Please refer to chapter3
Note: Another easy way to distinguish the system slot is
that the system slot uses red guide rails while the
peripheral slots use gray ones.
The insert/eject handles on CompactPCITM cards help users to install
and remove the cards easily and safely. Follow the procedures below
to install a card into a chassis:
To install a card:
1. Hold the card horizontally. Be sure that the card is oriented
correctly. The components of the card should be pointing to the
upper side.
2. Be sure that the handles of the card are not latched. Release the
handles if they are latched. Handles from different vendors may
have different latch designs.
Caution: Keep your fingers away from the latch hinges to
prevent your fingers from getting pinched.
3. Insert the card into the chassis by sliding the both edges of the
card into the card guides.
4. Push the card into the slot gently by sliding the card along the card
guide rails until the handles meet the rectangular holes of the
handle locker rails.
Note: If the card is correctly positioned and has been slid

Chapter 2 Hardware and drivers Installation 9
Figure 2-1: Installing a card into the chassis
all the way into the chassis, the handles should
match the rectangular holes. If not, remove the card
from the card guide and repeat step 3 again. Do not
try to install a card by forcing it into the chassis.
5. Left-pull the right handle and right-pull the left handle to push the
card into place.
6. Secure the card by locking the handles into place.
To remove a card:
1. Release the locking latches on the handles.
2. Push the both handles out to release the card from the backplane.
3. Slide the card out.

10 RIO-3302/RIO-3302S User's Manual
2.1.2 Driver installation
Devicedrivers and utilitys for DOS, Windows2000/95/98/NT and SCO
UNIXare included in the utility CD-ROMdisc.
The utility user's guide and installation instructions are provided in the
utility CD-ROM disc. The instructions are located in the directory
\RIO3302S\SCSI.

A
Pin Assignments
APPENDIX

12 RIO-3302/RIO-3302S User's Manual
A.1 J1 connector pin assignment
(RIO-3302S only)
Table A-1: J1 connector pin assignments
Pin Row A Row B Row C Row D Row E
25 +5 V REQ64# N/C N/C +5 V
24 AD1 +5 V N/C AD0 ACK64#
23 N/C AD4 AD3 +5 V AD2
22 AD7 GND N/C AD6 AD5
21 N/C AD9 AD8 M66EN C/BE0#
20 AD12 GND N/C AD11 AD10
19 N/C AD15 AD14 GND AD13
18 SERR# GND N/C PAR C/BE1#
17 N/C N/C N/C GND PERR#
16 DEVSEL# GND N/C STOP# N/C
15 N/C FRAME# IRDY# GND TRDY#
14
13 KEY AREA
12
11 AD18 AD17 AD16 GND C/BE2#
10 AD21 GND N/C AD20 AD19
9C/BE3# IDSEL AD23 GND AD22
8 AD26 GND N/C AD25 AD24
7 AD30 AD29 AD28 GND AD27
6REQ# GND N/C CLK AD31
5N/C N/C RST# GND GNT#
4N/C GND N/C N/C N/C
3INTA# N/C N/C +5 V N/C
2 N/C +5 V N/C N/C N/C
1+5 V N/C TRST# +12 V +5 V
# indicates "low active".

Appendix A Pin Assignments 13
A.2 J2 connector pin assignment
(RIO-3302S only)
Table A-2: J2 connector pin assignments
Pin Row A Row B Row C Row D Row E
22 N/C N/C N/C N/C N/C
21 N/C GND N/C N/C N/C
20 N/C N/C N/C GND N/C
19 N/C GND N/C N/C N/C
18 N/C N/C N/C GND N/C
17 N/C GND N/C N/C N/C
16 N/C N/C N/C GND N/C
15 N/C GND N/C N/C N/C
14 AD35 AD34 AD33 GND AD32
13 AD38 GND N/C AD37 AD36
12 AD42 AD41 AD40 GND AD39
11 AD45 GND N/C AD44 AD43
10 AD39 AD48 AD47 GND AD46
9 AD52 GND N/C AD51 AD50
8 AD56 AD55 AD54 GND AD53
7 AD59 GND N/C AD58 AD57
6 AD63 AD62 AD61 GND AD60
5C/BE5# GND N/C C/BE4# PAR64#
4N/C N/C C/BE7# GND C/BE6#
3N/C GND N/C N/C N/C
2 N/C N/C N/C N/C N/C
1 N/C GND N/C N/C N/C
# indicates "low active".