Advantech FWA-5070 User manual

User Manual
FWA-5070
1U RACKMOUNT NETWORK
APPLIANCE

FWA-5070 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2002507000 Edition 1
Printed in Taiwan January 2019

iii FWA-5070 User Manual
Declaration of Conformity
FCC Class A
This device complies with part 15 of the FCC rules: Operation is subject to the follow-
ing two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Cet appareil est conforme à la partie 15 des règles de la FCC: Le fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne doit pas provoquer d'interférences nuisibles.
2. Cet appareil doit accepter toute interférence re?ue, y compris les interférences
susceptibles de provoquer un fonctionnement indésirable.
Remarque: Cet équipement a été testé et déclaré conforme aux limites d'un appareil
numérique de classe A, conformément à la partie 15 des règles de la FCC. Ces lim-
ites sont con?ues pour fournir une protection raisonnable contre les interférences
nuisibles lorsque l'équipement est utilisé dans un environnement commercial. Cet
équipement génère, utilise et peut émettre de l'énergie radiofréquence et, s'il n'est
pas installé et utilisé conformément au manuel d'instructions, peut causer des inter-
férences nuisibles aux communications radio. L'utilisation de cet équipement dans
une zone résidentielle est susceptible de provoquer des interférences nuisibles,
auquel cas l'utilisateur devra corriger les interférences à ses frais.
CE MARK
The CE marking on this product indicates that it is in compliance with the European
Union EMC Directive 2014/30/EU, Safety Directive 2014/35/EU.
Le marquage CE sur ce produit indique qu'il est conforme à la Directive européenne
sur la compatibilité électromagnétique 2014/30 / UE, Directive sur la sécurité 2014/
35 / UE.
Note! The equipment is operated and maintained only by professionals
Remarque! L'équipement est exploité et entretenu uniquement par des profession-
nels

FWA-5070 User Manual iv
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
3. For more information please contact [e-mail] or visit www.advan-
tech.com/nc.
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.

v FWA-5070 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. Do not leave this equipment in an environment where the storage temperature
may go below -20° C (-4° F) or above 80° C (167° F). This could damage the
equipment. The equipment should be in a controlled environment.
16. Caution: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer, discard used
batteries according to the manufacturer's instructions.
17. RESTRICTED ACCESS AREA: The equipment should only be installed in a
Restricted Access Area.
18. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained
herein.

FWA-5070 User Manual vi
1. Lisez ces instructions de sécurité attentivement.
2. Conservez ce manuel d'utilisation pour référence ultérieure.
3. Débranchez cet équipement de toute prise secteur avant de le nettoyer. Utilisez
un chiffon humide. N'utilisez pas de détergent liquide ou pulvérisé pour le net-
toyage.
4. Pour les équipements enfichables, la prise de courant doit être située près de
l'équipement et doit être facilement accessible.
5. Gardez cet équipement à l'abri de l'humidité.
6. Placez cet équipement sur une surface fiable pendant l'installation. Le laisser
tomber ou le laisser tomber peut causer des dommages.
7. Les ouvertures sur l'enceinte servent à la convection de l'air. Protégez l'équipe-
ment contre la surchauffe. NE COUVREZ PAS LES OUVERTURES.
8. Assurez-vous que la tension de la source d'alimentation est correcte avant de
connecter l'équipement à la prise de courant.
9. Placez le cordon d'alimentation de manière à ce que personne ne puisse
marcher dessus. Ne placez rien sur le cordon d'alimentation.
10. Toutes les mises en garde et les avertissements sur l'équipement doivent être
notés.
11. Si l'équipement n'est pas utilisé pendant une longue période, débranchez-le de
la source d'alimentation pour éviter tout dommage d? à une surtension transit-
oire.
12. Ne versez jamais de liquide dans une ouverture. Cela pourrait provoquer un
incendie ou un choc électrique.
13. N'ouvrez jamais l'équipement. Pour des raisons de sécurité, l'équipement doit
être ouvert uniquement par du personnel qualifié.
14. Si l'une des situations suivantes se présente, faites vérifier l'équipement par le
personnel de service:
Le cordon d'alimentation ou la prise est endommagé.
Le liquide a pénétré dans l'équipement.
L'équipement a été exposé à l'humidité.
L'équipement ne fonctionne pas bien, ou vous ne pouvez pas le faire fonction-
ner selon le manuel de l'utilisateur.
L'équipement a été échappé et endommagé.
o L'équipement présente des signes évidents de rupture.
15. Ne laissez pas cet appareil dans un environnement où la température de stock-
age peut être inférieure à -40 ° C ou supérieure à 85 ° C. Cela pourrait endom-
mager l'équipement. L'équipement devrait être dans un environnement contr?lé.
16. Attention: Danger d'explosion si la batterie est incorrectement remplacée. Rem-
placez uniquement par le même type ou un type équivalent recommandé par le
fabricant, jetez les piles usagées conformément aux instructions du fabricant.
17. ZONE D'ACCES RESTREINTE: L'équipement ne doit être installé que dans
une zone d'accès restreint.
18. AVERTISSEMENT: Cet ensemble d'instructions est donné conformément à la
CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des
déclarations contenues dans ce document.

vii FWA-5070 User Manual
1. 请仔细阅读此安全操作说明。
2. 请妥善保存此用户手册供日后参考。
3. 用湿抹布清洗设备前，请从插座拔下电源线。请不要使用液体或去污喷雾剂清洗
设备。
4. 对于使用电源线的设备，设备周围必须有容易连接到的电源插座。
5. 请让设备远离潮湿环境。
6. 请在安装前确保设备放置在可靠的平面上，意外跌落可能会导致设备损坏。
7. 设备外壳的开口是用于空气对流，从而防止设备过热。请不要覆盖这些开口。
8. 当您连接设备到电源插座上前，请确认电源插座的电压是否符合要求。
9. 请将电源线安置在人们不易绊到的位置，并不要在电源在线覆盖任何杂物。
10. 请注意设备上的所有警告和注意标语。
11. 如果长时间不使用设备，请将设备与电源插座间的电线断开，避免设备被超目标
电压波动损坏。
12. 请不要让任何液体流入通风口，以免引起火灾或者电路短路。
13. 请不要自行打开设备。为了确保您的安全，请由经过认证的工程师来打开设备。
14. 如遇下列情况，请由专业人员来维修：
电源线或者插头损坏；
设备内部有液体流入；
设备曾暴露在于于潮湿的环境中使用；
设备无法正常工作，或您无法通过用户手册来使其正常工作；
设备跌落或者损坏；
设备有明显的外观破损。
15. 请不要把设备放置在超出我们建议的温度范围的环境，即不要低于 0°C(-
20°C;-4°F) 或高于 40°C(60°C;140°F)，否则可能会损坏设备。
16. 注意：如果电池放置不正确，将有爆炸的危险，因此，只可以使用制造商推荐的
同一种或者同等型号的电池进行替换。请按照制造商的指示处理已使用过的电
池。
17. 根据 IEC 704‐1:1982 规定，设备产生的音量不高于 70 分贝。
18. 免责声明：请安全训示符合 IEC 704‐1 要求。研华公司对其内容之准确性不承
担任何法律责任。
CCC
警告使用者：这是甲类资讯产品，在居住的环境中使用，可能会造成射频干扰，在这
种情况下，使用者会被要求采取某些适当的对抗。
声明：此为 A 级产品，在生活环境中，可能会造成无线干扰，在这种情况下，可能需
要用户对其干扰采取切实可行的措施。

FWA-5070 User Manual viii

ix FWA-5070 User Manual
Contents
Chapter 1 Specifications ......................................1
1.1 Overview ................................................................................................... 2
Table 1.1: .................................................................................... 2
1.2 System Outlook......................................................................................... 3
1.2.1 FRONT VIEW ............................................................................... 3
Figure 1.1 I/O and NMC............................................................... 3
Figure 1.2 LED & Button.............................................................. 4
1.2.2 REAR VIEW.................................................................................. 4
Figure 1.3 Rear view.................................................................... 4
1.3 System layout............................................................................................ 4
Figure 1.4 System Layout............................................................ 4
1.4 Block Diagram........................................................................................... 5
Figure 1.5 Block Diagram ............................................................ 5
Chapter 2 Connector List and Jumper and
Switch Setting7
2.1 Connector, Jumper and Switch Placement ............................................... 8
Figure 2.1 Jumper and Switch Placement ................................... 8
2.2 Connector List ........................................................................................... 8
2.3 Jumper Setting .......................................................................................... 9
2.4 Switch Setting ......................................................................................... 10
Chapter 3 Installation Guide ..............................11
3.1 CPU & Heatsink ...................................................................................... 12
Figure 3.1 CPU installation ........................................................ 12
3.2 Memory ................................................................................................... 12
Figure 3.2 DRAM installation ..................................................... 13
3.3 SATA HDD/SSD...................................................................................... 13
Figure 3.3 HDD installation........................................................ 14
Figure 3.4 M.2 and mSATA installation ..................................... 14
3.4 PCIe ........................................................................................................ 14
Figure 3.5 PCIe installation........................................................ 15
3.5 Slide Rail Installation Guide .................................................................... 15
3.5.1 Overview ..................................................................................... 15
3.5.2 Installation steps ......................................................................... 15
3.6 Install/remove NMC component.............................................................. 19
Figure 3.6 NMC installation ....................................................... 19
3.7 Install/remove Power Supply component................................................ 19
Figure 3.7 PSU installation ........................................................ 19
Chapter 4 Operation............................................21
4.1 Powering up/down the system ................................................................ 22
4.2 Booting from network via PXE ................................................................ 22
Table 4.1: PXE BIOS Options ................................................... 22
Chapter 5 BIOS Settings.....................................27

FWA-5070 User Manual x
5.1 BIOS Defaults ......................................................................................... 28
5.2 BIOS Setup Menu ................................................................................... 28
Figure 5.1 BIOS POST screen (example) ................................. 28
Figure 5.2 BIOS Setup Screen Organization............................. 29
5.2.1 Main Setup Menu........................................................................ 30
Figure 5.3 BIOS Setup Main screen.......................................... 30
Table 5.1: Table 7 BIOS Setup: Main Menu.............................. 30
5.2.2 Platform Setup Menu .................................................................. 32
Figure 5.4 Platform Setup Main screen ..................................... 32
Figure 5.5 Platform Setup: Console Redirection Menu ............. 33
Table 5.2: Platform Setup: COM0 Console Redirection Menu
Items......................................................................... 33
Figure 5.6 Platform Setup: USB Configuration Menu................ 34
Table 5.3: USB Configuration Menu.......................................... 35
Figure 5.7 Platform Setup: Trusted Computing ......................... 35
Table 5.4: Trusted Computing Menu......................................... 36
Figure 5.8 Platform Setup: Trusted Computing with TPM2.0 .... 36
Table 5.5: Trusted Computing Menu with TPM2.0.................... 37
Figure 5.9 Platform Setup: Trusted Computing with TPM1.2 .... 38
Table 5.6: Trusted Computing Menu with TPM1.2.................... 38
Figure 5.10Platform Setup: H/W monitor.................................... 39
Figure 5.11Platform Setup: Virtualization ................................... 40
Table 5.7: Virtualization Menu................................................... 40
Figure 5.12Platform Setup: Platform Management .................... 41
Table 5.8: Platform Management Menu .................................... 42
Figure 5.13Lan Bypass settings ................................................. 43
Table 5.9: Advantech Lan Bypass Menu................................... 43
5.2.3 Hardware setup menu ................................................................ 45
Figure 5.14Hardware Configuration Menu ................................. 45
Figure 5.15Chipset: Processor Configuration Menu................... 46
Table 5.10:Processor Configuration Menu................................. 46
Figure 5.16North Bridge Configuration Menu............................. 48
Table 5.11:Northbridge Configuration Menu .............................. 49
Figure 5.17Hardware Setup: PCI Subsystem............................. 50
Table 5.12:Hardware Setup: PCI Subsystem Menu Items......... 50
Figure 5.18Hardware Setup: UPI configuration.......................... 53
Table 5.13:Hardware Setup: QPI configuration Menu Items...... 53
Figure 5.19Hardware Setup: South Bridge configuration ........... 54
Table 5.14:Hardware Setup: South Bridge configuration Menu
Items......................................................................... 54
Figure 5.20Hardware Setup: SATA configuration ...................... 55
Table 5.15:Hardware Setup: SATA configuration Menu Items... 55
Figure 5.21Hardware Setup: USB configuration ........................ 57
Table 5.16:Hardware Setup: USB configuration Menu Items..... 57
Figure 5.22Hardware Setup: ACPI configuration ....................... 58
Table 5.17:Hardware Setup: ACPI configuration Menu Items.... 58
Figure 5.23Hardware Setup: Runtime Error logging configuration.
59
Table 5.18:Hardware Setup: Runtime Error logging Menu Items...
59
Figure 5.24NVMe configuration.................................................. 60
Figure 5.25VROC configuration ................................................. 61
5.2.4 Server Mgmt setup menu ........................................................... 62
Figure 5.26Server Mgmt configuration ....................................... 62
Table 5.19:Server Mgmt configuration Menu Items ................... 62
5.2.5 Setup POST & Boot Menu.......................................................... 63
Figure 5.27Boot Configuration.................................................... 63
Table 5.20:Boot Configuration.................................................... 63
Figure 5.28Post & Boot Setup: CSM Configuration Menu.......... 64
Table 5.21:CSM Configuration Menu ......................................... 64

xi FWA-5070 User Manual
Figure 5.29CSM16 Configuration ............................................... 65
5.2.6 Security Setup............................................................................. 66
Figure 5.30Administrator Setup .................................................. 66
5.2.7 Save & Exit Menu ....................................................................... 67
Figure 5.31Save & Exit Menu ..................................................... 67
Table 5.22: Save & Exit Menu Options........................................ 67

FWA-5070 User Manual xii

Chapter 1
1Specifications

FWA-5070 User Manual 2
1.1 Overview
Table 1.1:
System P/N FWA-5070L-00A1R FWA-5070Q-00A1R
Form Factor 1U - Rack Mount
Processor
System
Processor 1 x Intel® Xeon® Platinum 8100, Gold 6100 & 5100,
Silver 4100 and Bronze 3100 processors
Core Number
Depends on CPUFrequency
L2 Cache
Chipset C621 C626
BIOS AMI Efi 64Mbit
Virtualization VT-x, VT-d, EPT
Memory
Technology DDR4, 2133/2400/2666MHz
Max.capacity 384GB
Socket 12 x 288-pin RDIMM
ECC support Yes
Networking
Controller 1 x Intel i210-AT
1GbE 2 x 10/100/1000 Mbps RJ45 via Intel i210-AT chip
10GbE N/A 2 x 10G SFP+ via Intel
C625
LAN bypass LAN bypass is supported by NMC
Expansion PCIe 1x FH/HL PCIe gen3 x16 1x FH/HL PCIe gen3 x8
NMC 4 4
Storage
2.5"HDD/SSD 2
3.5"HDD N/A
m.2 SSD 1 x M.2 2280
Others 1 x mSATA
1 x internal SATA port
I/O
Console port 1
USB3.0 2
LED Indicator 1 x PWR_LED, 1 x Alert_LED, 1 x Locate_LED
Others 1 x Power Button
TPM TPM1.2
LCD Module N/A
Power
Power Type AC, redundant
Watts 650W
Input 100V ~ 240V
Connector CRPS
Environment
Operating
Temperature
(air flow 0.7 m/sec)
0 ~ 40 °C (32 ~ 104 °F)
Non-operating
Temperature
-20 ~ 80° C (-4 ~ 167° F) and 40° C @ 95% RH Non-
Condensing
Cooling 3 x 40cm Fan module

3 FWA-5070 User Manual
Chapter 1 Specifications
1.2 System Outlook
1.2.1 FRONT VIEW
1.2.1.1 I/O and NMC
Figure 1.1 I/O and NMC
Mechanical
Construction Steel
Mounting 1U rackmount
Dimensions
(W x H x D) 438 x 44 x 550(mm)
Weight 15 KG
OS Support Linux (CentOS, Red Hat, Ubuntu)
Advantech S/W Packages System diagnostic tool and quick start image
IPMI IPMI v2.0 compliant, with web interface, iKVM on
request (Advantech IPMI Core)
Certification CE/FCC/CB/UL/CCC
Table 1.1:

FWA-5070 User Manual 4
1.2.1.2 LED & Button
Figure 1.2 LED & Button
1.2.2 REAR VIEW
Figure 1.3 Rear view
1.3 System layout
System layout as below:
Figure 1.4 System Layout

5 FWA-5070 User Manual
Chapter 1 Specifications
1.4 Block Diagram
Figure 1.5 Block Diagram

FWA-5070 User Manual 6

Chapter 2
2Connector List and
Jumper and Switch
Setting

FWA-5070 User Manual 8
2.1 Connector, Jumper and Switch Placement
Figure 2.1 Jumper and Switch Placement
2.2 Connector List
Location Description Comment
CN32 Power Connector PSU1 P12V &P12V_STBY to MB
CN33 Power Connector PSU2 P12V &P12V_STBY to MB
CN61 Power Connector P12V for external power of PCIe card
CN62 Power Connector P12V for PoE NMC module
CN86 Power Connector P12V, P5V and P3V3 for NAMB-
6070HDD4BP
CN48 Board to Board Connector For NAMB-6070MGT
CN22 PCIE * 8 Connector For Advantech NMC module
CN23 PCIE * 8 Connector For Advantech NMC module
CN24 PCIE * 8 Connector For Advantech NMC module
CN25 PCIE * 8 Connector For Advantech NMC module
CN49 PCIE * 16 Connector For NAMB-6070PRC
CN50 PCIE * 8 Connector Reserving for other SKU
CN4 M.2 Connector PCIE & SATA
CN5 SATA Connector SATA port 0
CN6 SATA Connector SATA port 1
CN7 SATA Connector SATA port 2
CN8 SATA Connector SATA port 3
CN46 SATA Connector CN46 and CF1 are alternative by
JP10
CN47 mSATA Connector