Advantech EKI-1360-BE Series User manual

User Manual
EKI-1360-BE Series
1/2-port RS-232/422/485 to
802.11a/b/g/n WLAN Serial
Device Servers

EKI-1360-BE Series User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2018
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties, which may result from its use.
Acknowledgments
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (5 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for five years from the date of
purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is
defective, it will be repaired or replaced at no charge during the warranty period. For
out of-warranty repairs, you will be billed according to the cost of replacement
materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any on-screen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. Edition 1
Printed in Taiwan June 2018

iii EKI-1360-BE Series User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial
enclosure products.
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

EKI-1360-BE Series User Manual iv
Warnings, Cautions and Notes
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to:
[email protected]
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
1 x Gateway Server
1 x DIN-Rail Mounting Bracket and Screws
1 x Wall-mounting Bracket
2 x Antennas
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.

v EKI-1360-BE Series User Manual
Safety Instructions
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any DC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
Never pour any liquid into an opening. This may cause fire or electrical shock.
Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
–The power cord or plug is damaged.
–Liquid has penetrated into the equipment.
–The equipment has been exposed to moisture.
–The equipment does not work well, or you cannot get it to work according to
the user's manual.
–The equipment has been dropped and damaged.
–The equipment has obvious signs of breakage.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO -40°C (-40°F) ~ 80°C (176°F). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
The sound pressure level at theoperator's position accordingto IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.

EKI-1360-BE Series User Manual vi
Safety Precaution - Static Electricity
Static electricity can cause bodily harm or damage electronic devices. To avoid
damage, keep static-sensitive devices in the static-protective packaging until the
installation period. The following guidelines are also recommended:
Wear a grounded wrist or ankle strap and use gloves to prevent direct contact to
the device before servicing the device. Avoid nylon gloves or work clothes,
which tend to build up a charge.
Always disconnect the power from the device before servicing it.
Before plugging a cable into any port, discharge the voltage stored on the cable
by touching the electrical contacts to the ground surface.

vii EKI-1360-BE Series User Manual
Contents
Chapter 1 Introduction..........................................1
1.1 Overview...................................................................................................2
1.2 Device Features........................................................................................3
1.3 Specifications............................................................................................3
1.4 Dimensions ...............................................................................................4
Chapter 2 Getting Started.....................................6
2.1 Hardware...................................................................................................7
2.1.1 Front View.....................................................................................7
2.1.2 Rear View .....................................................................................9
2.1.3 Top View.......................................................................................9
2.1.4 LED Indicators ............................................................................10
2.2 Connecting Hardware .............................................................................11
2.2.1 DIN Rail Mounting.......................................................................11
2.2.2 Wall-Mounting.............................................................................13
2.2.3 Wireless Connection...................................................................14
2.2.4 Network Connection....................................................................16
2.2.5 Serial Connection........................................................................16
2.2.6 Power Connection.......................................................................17
2.3 Reset Button ...........................................................................................21
Chapter 3 Utility Configuration..........................22
3.1 Installing the Configuration Utility............................................................23
3.2 Starting the Configuration Utility..............................................................26
3.3 Discovering Your Device Server.............................................................27
3.3.1 Auto Searching ...........................................................................27
3.4 Network Settings.....................................................................................29
3.5 Administrator Settings.............................................................................31
3.5.1 Locate the Serial Device Server .................................................31
3.5.2 Restore to Factory Default Settings............................................32
3.5.3 Resetting the Device...................................................................33
3.5.4 Add to Favorite............................................................................34
3.5.5 Auto Mapping..............................................................................34
3.5.6 Manual Mapping .........................................................................34
3.5.7 Update Firmware ........................................................................35
Chapter 4 Selecting An Operating Mode ..........36
4.1 Understanding the EKI-1360-BE Series..................................................37
4.1.1 Product Description.....................................................................37
4.1.2 COM Port Redirector ..................................................................38
4.1.3 TCP Server Mode.......................................................................40
4.1.4 TCP Client Mode.........................................................................41
4.1.5 Serial Tunneling Mode................................................................42
4.1.6 UDP Server/Client Mode.............................................................42
4.1.7 Control Mode ..............................................................................42

EKI-1360-BE Series User Manual viii
Chapter 5 Setting up Virtual COM Port............. 43
5.1 Setting COM Port Redirector.................................................................. 44
5.2 Virtual COM Port Mapping...................................................................... 44
5.2.1 Auto Mapping.............................................................................. 44
5.2.2 Manual Mapping......................................................................... 46
5.2.3 Configuration Wizard.................................................................. 47
5.2.4 Confirming Virtual COM Settings................................................ 48
5.2.5 Removing VCOM Ports .............................................................. 50
5.2.6 Exporting and Importing VCOM Mapping................................... 51
Chapter 6 Web Interface ....................................52
6.1 Overview................................................................................................. 53
6.2 Accessing the Web Page........................................................................ 53
6.2.1 Accessing the Web Page via Configuration Utility...................... 53
6.2.2 Accessing the Web Page via Web Browser ............................... 54
6.3 Overview................................................................................................. 54
6.4 Network Settings..................................................................................... 55
6.4.1 LAN............................................................................................. 55
6.5 Wireless Settings.................................................................................... 56
6.5.1 Basic........................................................................................... 56
6.5.2 Advanced.................................................................................... 57
6.5.3 Security....................................................................................... 58
6.5.4 Statistics ..................................................................................... 59
6.5.5 Site Survey ................................................................................. 60
6.5.6 Access Control............................................................................ 61
6.5.7 Log.............................................................................................. 62
6.6 Port Configuration................................................................................... 63
6.6.1 Basic........................................................................................... 63
6.6.2 Operation.................................................................................... 64
6.6.3 Advanced.................................................................................... 65
6.7 Monitor.................................................................................................... 66
6.7.1 Setting......................................................................................... 66
6.7.2 Statistic....................................................................................... 67
6.7.3 Connected IP.............................................................................. 68
6.8 Alarm....................................................................................................... 69
6.8.1 Setting......................................................................................... 69
6.8.2 Event........................................................................................... 70
6.8.3 LogFile........................................................................................ 72
6.9 Administration......................................................................................... 72
6.9.1 System........................................................................................ 72
6.9.2 Syslog......................................................................................... 73
6.9.3 HTTP .......................................................................................... 73
6.9.4 Configuration .............................................................................. 74
6.9.5 Firmware Upgrade...................................................................... 74
6.9.6 Tools........................................................................................... 75
Chapter 7 Telnet/Serial Console Configuration76
7.1 Overview................................................................................................. 77
7.2 Telnet Console........................................................................................ 77
7.2.1 Create a new connection............................................................ 77
7.2.2 Input the IP address.................................................................... 78
7.2.3 Connection Success................................................................... 78
7.3 Command List......................................................................................... 79
7.3.1 system ........................................................................................ 79
7.3.2 port.............................................................................................. 79

ix EKI-1360-BE Series User Manual
7.3.3 portadv........................................................................................80
7.3.4 mvcom ........................................................................................80
7.3.5 mctrl............................................................................................81
7.3.6 mdata..........................................................................................81
7.3.7 net...............................................................................................81
7.3.8 password.....................................................................................82
7.3.9 alarm...........................................................................................82
7.3.10 monitor........................................................................................82
7.3.11 time.............................................................................................82
7.3.12 service.........................................................................................83
7.3.13 apply ...........................................................................................83
7.3.14 exit ..............................................................................................83
7.3.15 help.............................................................................................83
7.3.16 import..........................................................................................83
7.3.17 export..........................................................................................83
7.3.18 wireless.......................................................................................83
7.3.19 wirelessadv.................................................................................84
Chapter 8 TCP and UDP Port Numbers.............86
8.1 List of Known TCP and UDP Port Numbers............................................87

EKI-1360-BE Series User Manual x
List of Figures
Figure 1.1 EKI-1361 Dimensions.................................................................................................... 4
Figure 1.2 EKI-1362 Dimensions.................................................................................................... 5
Figure 2.1 EKI-1361 Front View..................................................................................................... 7
Figure 2.2 EKI-1362 Front View..................................................................................................... 8
Figure 2.3 Rear View...................................................................................................................... 9
Figure 2.4 Top View ....................................................................................................................... 9
Figure 2.5 System LED Panel......................................................................................................10
Figure 2.6 Installing the DIN-Rail Mounting Kit............................................................................. 11
Figure 2.7 Correctly Installed DIN Rail Kit.................................................................................... 12
Figure 2.8 Removing the DIN-Rail................................................................................................ 12
Figure 2.9 Installing Wall Mount Plates........................................................................................ 13
Figure 2.10 Wall Mount Installation................................................................................................ 14
Figure 2.11 Installing the Antenna.................................................................................................. 14
Figure 2.12 Positioning the Antenna ..............................................................................................15
Figure 2.13 Ethernet Plug & Connector Pin Position...................................................................... 16
Figure 2.14 DB9 Pin Assignment ...................................................................................................16
Figure 2.15 Power Wiring for EKI-1360-BE Series......................................................................... 17
Figure 2.16 Grounding Connection ................................................................................................ 19
Figure 2.17 Terminal Receptor: Relay Contact.............................................................................. 19
Figure 2.18 Terminal Receptor: Power Input Contacts .................................................................. 20
Figure 2.19 Removing a Terminal Block ........................................................................................ 20
Figure 2.20 Installing DC Wires in a Terminal Block...................................................................... 21
Figure 2.21 Securing a Terminal Block to a Receptor.................................................................... 21
Figure 3.1 InstallShield Wizard 1 of 4...........................................................................................23
Figure 3.2 InstallShield Wizard 2 of 4...........................................................................................24
Figure 3.3 InstallShield Wizard 3 of 4...........................................................................................24
Figure 3.4 InstallShield Wizard 4 of 4...........................................................................................25
Figure 3.5 Configuration Utility Overview..................................................................................... 26
Figure 3.6 Open View of Serial Device Configuration Utility ........................................................ 27
Figure 3.7 Selecting a Group........................................................................................................ 28
Figure 3.8 Selecting a Device....................................................................................................... 28
Figure 3.9 Viewing Basic Settings................................................................................................28
Figure 3.10 Utility Overview............................................................................................................ 29
Figure 3.11 Network Settings Overview ......................................................................................... 30
Figure 3.12 Locate the Serial Device Server.................................................................................. 31
Figure 3.13 Restore to Factory Default Settings ............................................................................ 32
Figure 3.14 Reset Device............................................................................................................... 33
Figure 3.15 Add to Favorite............................................................................................................ 34
Figure 3.16 Update Firmware......................................................................................................... 35
Figure 4.1 Single Ethernet Connection......................................................................................... 37
Figure 4.2 COM Port Redirector...................................................................................................38
Figure 4.3 Multi-Access Mode...................................................................................................... 39
Figure 4.4 TCP Server Mode........................................................................................................ 40
Figure 4.5 TCP Client Mode......................................................................................................... 41
Figure 4.6 Serial Tunneling Mode ................................................................................................ 42
Figure 5.1 Selecting Auto Mapping .............................................................................................. 44
Figure 5.2 Selecting Auto Mapping .............................................................................................. 45
Figure 5.3 Mapping Selected Ports.............................................................................................. 45
Figure 5.4 Viewing VCOM Mapping Results................................................................................ 45
Figure 5.5 Selecting Manual Mapping.......................................................................................... 46
Figure 5.6 Viewing Manual VCOM Mapping Results ................................................................... 46
Figure 5.7 Viewing Manual VCOM Mapping Results ................................................................... 47
Figure 5.8 Selecting the Configuration Wizard............................................................................. 47
Figure 5.9 Serial Port Listing on EKI-1360-BE Series Device...................................................... 48
Figure 5.10 System Port VCOM Mapping Configuration................................................................ 49
Figure 5.11 Verifying VCOM Mapping Configuration ..................................................................... 49

xi EKI-1360-BE Series User Manual
Figure 5.12 Remove VCOM Port....................................................................................................50
Figure 6.1 Accessing the Web Page via Configuration Utility.......................................................53
Figure 6.2 System.........................................................................................................................54
Figure 6.3 Network Settings > LAN ..............................................................................................55
Figure 6.4 Wireless Settings > Basic............................................................................................56
Figure 6.5 Wireless Settings > Advanced.....................................................................................57
Figure 6.6 Wireless Settings > Security........................................................................................58
Figure 6.7 Wireless Settings > Statistics ......................................................................................59
Figure 6.8 Wireless Settings > Site Survey ..................................................................................60
Figure 6.9 Wireless Settings > Access Control.............................................................................61
Figure 6.10 Wireless Settings > Log...............................................................................................62
Figure 6.11 Port Configuration > Basic...........................................................................................63
Figure 6.12 Port Configuration > Operation....................................................................................64
Figure 6.13 Port Configuration > Operation....................................................................................65
Figure 6.14 Monitor > Setting .........................................................................................................66
Figure 6.15 Monitor > Statistic........................................................................................................67
Figure 6.16 Monitor > Connected IP...............................................................................................68
Figure 6.17 Alarm > Setting............................................................................................................69
Figure 6.18 Alarm > Event..............................................................................................................71
Figure 6.19 Alarm > LogFile ...........................................................................................................72
Figure 6.20 Administration > System..............................................................................................72
Figure 6.21 Administration > Syslogd.............................................................................................73
Figure 6.22 Administration > HTTP ................................................................................................73
Figure 6.23 Administration > Configuration ....................................................................................74
Figure 6.24 Administration > Firmware Upgrade............................................................................74
Figure 6.25 Administration > Tools.................................................................................................75
Figure 7.1 Creating a Telnet Connection......................................................................................77
Figure 7.2 Creating a Telnet Connection......................................................................................78
Figure 7.3 Telnet Connection Console .........................................................................................78

Chapter 1
1Introduction

2 EKI-1360-BE Series User Manual
1.1 Overview
Advantech's EKI-1360-BE Series of Industrial Device Servers are a robust, feature-
rich, and cost-effective way to network-enable equipment in an industrial automation
environment. The EKI-1360-BE Series provides one or two serial ports,
802.11a/b/g/n wireless LAN interface to connect any RS-232/422/485 devices to
wireless LAN. These wireless serial device servers provide serial-to-wireless network
connectivity as an alternative to wired Ethernet connectivity and enable virtually any
serial device or equipment to be remotely accessed, controlled, monitored, or shared
on an 802.11a/b/g/n wireless network.
By encapsulating serial data and transporting it over Ethernet, the EKI-1360-BE
Series allows virtual serial links over Ethernet IP-based networks. After the
Advantech Serial Device Server Configuration Utility is installed, a standard serial
operation calls with virtual COM port could be transparently redirected to the serial
device servers, guaranteeing compatibility with legacy serial devices and enabling
backward compatibility with existing software. EKI-1360-BE Series also supports
serial tunneling, allowing two native serial devices to communicate over a network
without any hosts or programming. As a result, you can extend a limited distance,
point-to-point, direct serial connections within the plant, throughout the factory, the
facility, the office building, or across the global enterprise.
The EKI-1360-BE Series provides an impressive list of features and functions
enabling multiple industrial devices to be connected, controlled, configured,
managed, and updated over a network. With serial ports and 802.11a/b/g/n wireless
LAN, the EKI-1360-BE Series easily connects multiple serial devices to a network.
The transmission speed of the EKI-1360-BE Series is up to 921.6 Kbps totally
outstripping the competition to meet the demand for high-speed exchange.
Functionally transparent and efficient, the EKI-1360-BE Series is specially designed
for remotely controlling and monitoring devices via the Internet.
The EKI-1360-BE Series provides roaming ability. EKI-1360-BE Series can migrate
from AP to AP during certain condition. In some field applications, the device can't
use a fixed physical connection, such as AGV, transportation, and cross wide space
communication. EKI-1360-BE Series can easily installed to fulfill this requirement.
With a compact size and lightweight design, the EKI-1360-BE Series can be installed
in moving vehicles without much extra wight.
Types of supported devices:
Human Machine Interface (HMI)
Programmable Logic Controller (PLC)
Flow meters
Temperature / pressure monitoring equipment
Gas leak detection device
Scales
Power monitoring equipment
Data Acquisition Modules
The EKI-136X series provides various operation modes: COM port redirection
(Virtual COM port), TCP/UDP server/client mode. Serial devices can be connected
by means of multi-access modes.

EKI-1360-BE Series User Manual 3
1.2 Device Features
Supports standard Wireless 802.11a/b/g/n
Supports MIMO 2x2 technology
Expandable up 4096 serial ports for one single host
Provides 10/100/1000 Mbps auto-sensing Ethernet ports for easy diagnostic
Supports any baud rate setting from 50 bps up to 921.6 Kbps
Supports various operation modes: COM port redirection (Virtual COM port),
TCP server/client, UDP server/client, control mode and RFC-2217 mode
Easy to diagnostic LED indicators
Supports multi-access features: allows maximum 5 hosts to access one serial
port simultaneously
Allows a maximum of 16 peers in TCP/UDP client mode
Mounts on DIN rail, wall, or panel easily
Surge protection for RS-422/485 line and power supply
SNMP MIB-II for network management
1.3 Specifications
Specifications Description
Interface I/O Port EKI-1361: 1 x RJ45 + 1 x RS-232/422/485
EKI-1362: 1 x RJ45 + 2 x RS-232/422/485
Power Connector Terminal block
Physical Enclosure Metal shell with solid mounting kits
Installation DIN-Rail and Wall mount
Dimensions
(W x H x D) 30 x 140 x 95 mm (1.18" x 5.51" x 3.74")
LED Display System LED Power 1, Power 2, Status
Port LED WLAN: Quality, Link/Active
LAN: Speed, Link/Active
Serial: Tx, Rx
Environment Operating
Temperature -40°C ~ 75°C (-40°F ~ 166°F)
Storage
Temperature -40°C ~ 80°C (-40°F ~ 176°F)
Ambient Relative
Humidity 10 ~ 95% RH
Wireless LAN
Communications Compatibility IEEE 802.11a/b/g/n
Speed Up to 300Mbps
Antenna 2 x Reverse SMA (supports 2T2R)
Free Space
Range Open space 100 m
Wireless Security WEP, WPA/WPA2-Personal, WPA/WPA2-Enterprise
Ethernet
Communications Compatibility IEEE 802.3, IEEE 802.3u
Speed 10/100/1000 Mbps
Port Connector 8-pin RJ45
Protection Built-in 1.5 KV magnetic isolation

4 EKI-1360-BE Series User Manual
1.4 Dimensions
The following view depicts the EKI-1361.
Figure 1.1 EKI-1361 Dimensions
Serial
Communications Port Type RS-232/422/485, software selectable
Port Connector DB9 male
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Odd, Even, Space, Mark
Baud Rate 50 bps ~ 921.6 kbps, any baud rate setting
Protection 15 KV ESD for all signals
Power Power
Consumption EKI-1361: 8W
EKI-1362: 9W
Power Input 12 ~ 48VDC, redundant dual inputs
Software Driver Support 32-bit/64-bit Windows XP/Vista/7/8/8.1/10, Windows
Server 2003/2008/2008 R2/2012/2012 R2 and Linux
Utility Advantech EKI Device Configuration Utility
Operation Modes Access Point mode/Station mode
COM port redirection mode (Virtual COM)
TCP/UDP server (polling) mode
TCP/UDP client (event handling) mode
Configuration Windows utility, Telnet console, Web Browser
Protocol ARP, ICMP, IPv4, IPv6, TCP, UDP, BOOTP, DHCP
Client, Auto IP, Telnet, DNS, SNMP, HTTP, SMTP,
SNTP
Regulatory
Approvals EMC CE, FCC Part 15 Subpart B (Class B)
Specifications Description
Reset
WLAN
50.70 [2.00]
95 [3.74]
69 [2.72]
99.20 [3.91]
123 [4.84]
30 [1.18]
30 [1.18]
140 [5.51] 140 [5.51]
66 [2.60]
8 [0.31]
10.30 [0.41]
140 [4.09] 6.30 [0.25]
48 [1.89] 47 [1.85] 45 [1.77]
104 [4.09]
15 [0.59]
15 [0.59]
14.53
[0.57]
9 [0.35]

EKI-1360-BE Series User Manual 5
The following view depicts the EKI-1362.
Figure 1.2 EKI-1362 Dimensions
Reset
WLAN
50.70 [2.00]
95 [3.74]
69 [2.72]
99.20 [3.91]
123 [4.84]
30 [1.18]
30 [1.18]
140 [5.51] 140 [5.51]
66 [2.60]
8 [0.31]
10.30 [0.41]
140 [4.09] 6.30 [0.25]
48 [1.89] 47 [1.85] 45 [1.77]
104 [4.09]
15 [0.59]
15 [0.59]
14.53
[0.57]
9 [0.35]

Chapter 2
2Getting Started

EKI-1360-BE Series User Manual 7
2.1 Hardware
2.1.1 Front View
The following view shows the EKI-1361.
Figure 2.1 EKI-1361 Front View
No. Item Description
1 Antenna connector Connector for antenna.
2 System LED panel See “LED Indicators” on page 10 for further details.
3 ETH port RJ45 ports x 1.
4 Serial port DB9 pinout, supports RS-232/422/485.
5 Reset button Button allows for system soft reset or factory default reset.
EKI-1361
Reset
P1 P2 Status
WLAN
TX RX
1
3
4
1
2
5

8 EKI-1360-BE Series User Manual
The following view shows the EKI-1362.
Figure 2.2 EKI-1362 Front View
No. Item Description
1 Antenna connector Connector for antenna.
2 System LED panel See “LED Indicators” on page 10 for further details.
3 ETH port RJ45 ports x 1.
4 Serial port DB9 pinout, supports RS-232/422/485.
5 Reset button Button allows for system soft reset or factory default reset.
EKI-1362
Reset
P1 P2 Status
WLAN
TX RX
TX RX
1
3
4
1
2
4
5

EKI-1360-BE Series User Manual 9
2.1.2 Rear View
Figure 2.3 Rear View
2.1.3 Top View
Figure 2.4 Top View
No. Item Description
1 DIN-Rail mounting
plate Mounting plate used for the installation to a standard DIN rail
1
No. Item Description
1 Terminal block Connect cabling for power and alarm wiring
2 Ground terminal Screw terminal used to ground chassis
3 Wall mounting holes Screw holes (x4) used in the installation of a wall mounting plate
PWR2
P-Fail
DC12-48V
PWR1
V2- V2+ V1- V1+
1A@24V
13
2