Advantech FWA-6510 User manual

FWA-6510 H/W Installation
APPROVALS
Name (printed)
Title
Signature
Date

FWA-6510 H/W installation
Version: V1.0 Page 2 of 21
HISTORY
Revision
Date
Person
Description
V1.0

FWA-6510 H/W installation
Version: V1.0 Page 3 of 21
CONTENT INDEX
1. Hardware installation Introduction................................................................................4
1-1 Open Chassis cover......................................................................................….4
1-2 CPU & heat-sink Installation..............................................................................5
1-3 Memory module installation...............................................................................9
1-4 Extend cable & module installation .................................................................11
1-5 Riser card installation......................................................................................13
1-6 Close Chassis Cover.......................................................................................15
1-7 HDD and HDD tray installation........................................................................16
2. Front Panel connector Introduction............................................................................18
2-1 RJ45 connector introduction............................................................................18
2-2 LED, USB and power button introduction........................................................19

FWA-6510 H/W installation
Version: V1.0 Page 4 of 21
1. HARDWARE INSTALLATION INTRODUCTION
1-1 Open Chassis cover
1. Kindly use screwdriver to unlock 2 side screws & chassis rear screw.
Side screw
Rear screw
2. Kindly push top cover back about 1.5cm, and pick up top cover, it may remove FWA-6510 Chassis cover

FWA-6510 H/W installation
Version: V1.0 Page 5 of 21
1-2 CPU & heat-sink Installation
1. Kindly unlock FAN duct’s 2 screws
2. Kindly pull a “OPEN 1st”lever of CPU socket , pull another lever of CPU socket and pull back load plate

FWA-6510 H/W installation
Version: V1.0 Page 6 of 21
3. Kindly remove a protected cover from socket.
4. Kindly put CPU on the socket, and please checks CPU’s gaps and socket’s prominence, please don’t put
wrong

FWA-6510 H/W installation
Version: V1.0 Page 7 of 21
5. Kindly lay down load plate; close a “close 1st”lever of CPU socket, and close another lever of CPU socket
6. Kindly smear the HEAT SINK COMPOUND on CPU well mixed

FWA-6510 H/W installation
Version: V1.0 Page 8 of 21
7. Please use screwdriver to fix heat-sink module and please follow diagonal to fix screw.

FWA-6510 H/W installation
Version: V1.0 Page 9 of 21
1-3 Memory module installation
1, kindly installs DDR3 ECC+REG RAM module on the socket, and please checks RAM gaps and socket’s
prominence.
2. When customer installs 2 CPU in system, the minimum RAM requirement is 4 PCs, and it needs to
install in A1/C1/E1/G1 DIMM socket.
3. If customer installs CPU in FWA-6510, A CPU needs to install in CPU socket 1 , the minimum RAM
requirement is 2 PCs, and it needs to install in A1/C1 DIMM socket.
4. When customer needs to install more RAM module in system; recommending RAM installation sequence is
A1/B1/C1/D1/E1/F1/G1/H1, and then A2/B2/C2/D2

FWA-6510 H/W installation
Version: V1.0 Page 10 of 21
3. When CPU & Memory installs finish, kindly install FAN duct in chassis.

FWA-6510 H/W installation
Version: V1.0 Page 11 of 21
1-4 Extend cable & module installation
1. If customer needs to use FWA-6510 VGA function, kindly install VGA cable (P/N: 1700019367) into CN15

FWA-6510 H/W installation
Version: V1.0 Page 12 of 21
2. Kindly covers & don’t close chassis cover, and pull out VGA cable from chassis when customer uses
FWA-6510 VGA function.
3. If customer needs to debug system boot issue, please install “Port80 module”(option) into CN 9

FWA-6510 H/W installation
Version: V1.0 Page 13 of 21
1-5 Riser card installation
1. Kindly use screwdriver to unlock front plate’s screw and remove front plate from Chassis
2. FWA-6510 Riser card only support PCIe X1/X4/X8 riser card, Please don’t install PCIe X16 riser card
3. Kindly use screwdriver to unlock plate’s screw, and remove IO card holder.

FWA-6510 H/W installation
Version: V1.0 Page 14 of 21
4. Kindly use screwdriver to lock riser card and IO card holder
5. Kindly use screwdriver to lock riser card in FWA-6510 chassis

FWA-6510 H/W installation
Version: V1.0 Page 15 of 21
1-6 Close Chassis Cover
1. FWA-6510’s cover has 4 short posts,
When user has to cover on top cover, short posts need to place in track
2. Kindly close chassis cover and use screwdriver to lock 3 chassis screws,

FWA-6510 H/W installation
Version: V1.0 Page 16 of 21
1-7 HDD and HDD tray installation
1. Kindly unlock HDD orange lock key.
2. Kindly push blue line button, the handle HDD tray will auto pop up, please pull HDD tray from chassis
3. Kindly get 4 screws from accessory.

FWA-6510 H/W installation
Version: V1.0 Page 17 of 21
4. Kindly use screwdriver to lock 4 screws , let 2.5”HDD to fix in HDD tray
5. Kindly insert HDD tray into Chassis, and lock HDD orange lock key.

FWA-6510 H/W installation
Version: V1.0 Page 18 of 21
2. FRONT PANEL CONNECTOR INTRODUCTION
2-1 RJ45 connector introduction
1. Condole port : It is a COM port of RJ45 type,
If customer needs to remote control by console redirection, kindly use RJ45 to console cable to connect
FWA-6510’s COM port and Test PC’s RS232 COM port
2. MGMT (Manage) LAN port: It is Intel 82574L LAN port, and it is a BMC LAN port too.
User can use this port to remote control FWA-6510 by network, and it can use this LAN port to control
FWA-6510 BMC (IPMI) function.
3. HA (High available) LAN port: It is Intel 82574L LAN port,
User can set this LAN port as HA (High available) data transfer.

FWA-6510 H/W installation
Version: V1.0 Page 19 of 21
2-2 LED, USB and power button introduction
Panel LED
1. It is an alarm LED, When FWA-6510 has an alarm event or turn off, and the LED will show Amber
2. It is location LED, User may key-in IPMI command to enable this LED (Blue color ) to help user find this
LED on Rack mount.
Ex: When user key-in “ipmitool chassis identify”command, location LED will turn on (default is 15 seconds)
3. It is a power LED, when system power on, the LED will show Green
4. It is a power button, when user press this button, FWA-6510 will turn-on

FWA-6510 H/W installation
Version: V1.0 Page 20 of 21
5. USB Port, The front panel of FWA-6510 has two USB port.
HDD LED
1. Green LED is a HDD active LED, when green LED turns on, it means HDD is reading/writing.
2. Amber LED is a HDD status LED (4 HDD tray version only)
2-1 When Amber LED is short blinking, it is just for indication.
2-2 When Amber LED is long blinking, it means HDD is rebuilding
2-3 When Amber LED is always turn on, it means HDD is fail, please exchange new HDD ASAP.
Rear panel LED
Power LED color: Green/Red
LED will be ‘Green’when Power is running healthily.
LED will be ‘Green blinking’when Power status is stand by, Power only provide +5Vsb to system.
LED will be ‘Turn off’when power cord is unplugged
LED will be ‘Red’when power is fail