ADVENOR POWER TOWER Supplement

ADVENOR
POWER TOWER
Assembly & Operation Manual
Scan to view assembly video or visit
https://youtu.be/OtVR7X65yOg

Read Before Assembly
1.The product should be placed on a clean and smooth surface. Do not use it
near water or outdoors.
2.Please make sure all screws, bolts and knobs are tightened before using this
product.
3.This product can only be used by one person at the same time.
4.If the user feels dizzy, nausea, chest tightness or other symptoms, they
should stop using it immediately and seek medical treatment in time.
5.When using this product, it is recommended that users wear suitable fitness
clothes and sports shoes.
6.When using it, avoid placing any sharp objects around the product.
7.Any disabled person who is not monitored by a guardian or caregiver may not
use this product.
8.Before training, you should usually do various stretching exercises to warm
up.
9.If the product's function is defective, please stop using it.
If you have any inquiries or require further assistance, please contact
ADVENOR customer support by
Phone: [phone]
Email: service@advenorfitness.com
1

1. Name of Parts
Pull-up Bar
Adjusting Tube
Supporting Tube
Back Cushion
Back-connecting Bar
Locking knob
Arm Cushion
Adjusting Knob
Dip Bar
Stabilizing Tube
Connecting Bar
Cross Bar
Push-up Bar
Stabilizer
2

2. Parts in the Package
Supporting Tube ×2
Adjusting Tube ×2 Pull-up Bar ×1 Arm Cushion ×2
Back-connecting Bar ×1 Back Cushion ×1
Bolt B1
Bolt B2
Bolt A Locking knob
Adjusting Knob
Bolt C1
Bolt C2 Back-up Plate
Allen Wrench #1
(Thicker than Allen wrench #2)
(One of washers
on each Bolt B2
is bent)
(With washers)
Wrench
A
B
Allen Wrench #2
Screw D
Stabilizer ×2
Dip Bar ×2
Stabilizing Tube ×2
Cross Bar ×1
Connecting Bar ×2
x 4
x 12
x 2
x 2x 2
x 2
x 2
x 8
x 8
3

3. Assembly Instruction
Tip 1: Please kindly note that in order to ensure that the product arrives in good
condition and avoid possible damage or deformation during transportation, we
have specially reinforced the packaging on two main supporting tubes with
short steel pipes which will not be used during installation. Please take them out
by following the guidance before assembly.
4
Supporting Tube
Short Protective
Steel Pipe
Strap
Supporting Tube
Short Protective
Steel Pipe
Supporting Tube
Short Protective
Steel Pipe
1. Cut the straps
2. Pull one end of the short protective
steel pipe and take out the pipe
3. Discard the short protective steel pipe

Step 1
Install the two supporting tubes and one cross bar to the stabilizers. Please
attach the supporting tube first.
Tip 2: Please kindly note that it’s recommended to have two people complete
the assembly together. To ensure a smooth assembly process, please do not
tighten the screws to the max until you have all the metal parts installed
together. Please also note that two washers on Bolt A/ Bolt B1/ Bolt B2 should
be put separately on each end of it.
A
Allen wrench #1
Bolt A
Wrench
x 4
5

Step 2
Install two stabilizing tubes and the other cross bar to the stabilizers. Please
attach the stabilizing tube first. When attaching the stabilizing tubes to the sup-
porting tubes, please also put the back-up plates as shown in the picture.
AAllen wrench #1 Bolt A
Wrench
x 4
x 4
Bolt B1
Wrench
B
Allen wrench #2
Back-up Plate
x 2
6
(Mind the Installing
Direction of Bolt B1)

Step 3
Install the stabilizing tube #3 which is thinner than stabilizing tube #1 and #2 to
two supporting tubes. Put the back-up plates on both sides.
7
x 4
Bolt B1
Wrench
B
Allen wrench #2
Back-up Plate
x 2
(Mind the Installing
Direction of Bolt B1)

Step 4
Install the back-connecting bar and back cushion.
Bolt C2
x 2
Allen wrench #2
Allen wrench #2 Screw D
x 4
8
(With washers)

Step 5
Install the arm cushions and dip bars.
Allen wrench #2 Allen wrench #2
Screw D
x 8
Dip Bar ×2Arm Cushion ×2
Bolt C1
x 2
9

Step 6
Install the adjusting tubes and pull-up bar. Insert the adjusting tubes into the
main supporting tubes on both sides respectively to the lowest positions and
then install the push-up bar.
Allen wrench #2 Bolt B2
(One of the washers on
each Bolt B2 is bent)
x 2
Wrench
B
Adjusting Tube ×2
Pull-up Bar ×1
(Mind the Installing
Direction of Bolt B2)
10

Step 7
Raise the adjusting tubes to the suitable height and lock the position by tight-
ening the locking knobs as well as the adjusting knobs on both sides as shown
in the picture below. Please kindly note that there are 5 adjustable height
levels.
Locking knob
Adjusting Knob
x 2
x 2
★ Please tighten all the screws and bolts to the max to complete the assembly.
11

4. Recommended Exercises
12

Acknowledgements
Dear customer,
Thank you for choosing ADVENOR. We commit to provide the
best products and services to every customer.
If you have any inquiries or require further assistance, please
contact ADVENOR customer support by
Phone: [phone]
Email: service@advenorfitness.com
Your feedback and suggestions are always important and
valuable to us.
Kindest regards,
Company Founder
Scan to view assembly video or visit
https://youtu.be/OtVR7X65yOg