AEG APP10 User manual

APP10

2
2
Important!
It is essential that you read the instructions in this manual before
assembling, operating, and maintaining the product.
Subject to technical modifications.
x 1
x 1 x 1
x 1
x 1
APP10

33
x 1
x 1 x 1
x 1
x 1
APP10

4
4
BAR BOLT
OIL RESERVOIR
CAP
CHAIN
TENSIONING SCREW
ATTACHMENT
SHAFT
CHAIN
BAR
BRANCH HOOK

55
BAR BOLT
OIL RESERVOIR
CAP
CHAIN
TENSIONING SCREW
ATTACHMENT
SHAFT
CHAIN
BAR
BRANCH HOOK

6
6
3-4 mm
11
16
15
8
OPERATING THE PRODUCT
ADJUSTING THE CHAIN
REPLACING THE CHAIN AND BAR
FITTING AND REMOVING THE SCABBARD

77
3-4 mm
19
20
9
INSTALLING THE ATTACHMENT
STORING THE PRODUCT
CLEANING THE PRODUCT

8
8
2
3
4
1
click
FITTING AND REMOVING THE SCABBARD

99
2
3
4
1
click
INSTALLING THE ATTACHMENT
NOTE: Always ensure that the inner
shafts are fully seated together. If they
are not, the chain does not spin and
may cause damage to the inner shafts.

10
10
5
1
2
3

11 11
2
1
12
≤60˚
≥15m (50’)
10m
1
2
18V18V 58V
5
1
2
3
WARNING: DANGER! Risk of
electrocution! Do not operate within 10
m of overhead electrical power lines.
Position the product at an angle of 60° or
less, depending on the specific situation.
Keep bystanders at least 15 m away.
WARNING: Do not cut from a ladder.
This is extremely dangerous. Leave this
operation to professionals.
OPERATING THE PRODUCT

12
12
3
4
click
5
6

13 13
click
click
7
8
9
10
1
2
1
2
18V18V 18V58V
3
4
click
5
6

14
14
1
3
2
2
3
11
2
1
12
18V18V 58V
3-4 mm
1
2
2
1
3-4 mm
1
2
3
2
1
4
NOTE: The chain tension is correct when
the gap is 3–4 mm. Check the chain
tension regularly, as the chain stretches
when it heats up.
NOTE: Make a shallow first cut (1/4 of the
limb diameter) on the underside of the
limb close to the main limb or trunk. Make
a second cut from the top side of the limb
outboard from the first cut. Lastly, make
a final cut close to trunk. For the second
and final cuts (from the top of the limb or
branch), hold the branch hook against the
limb being cut. Allow the chain to cut for
you. Exert only light downward pressure.
ADJUSTING THE CHAIN
NOTE: Maximum cutting capacity (18V):
100 mm
Maximum cutting capacity (58V): 200 mm

15 15
1
3
2
2
3
11
2
1
12
18V18V 58V
3-4 mm
1
2
2
1
3-4 mm
1
2
3
2
1
4
NOTE: The chain tension is correct when
the gap is 3–4 mm. Check the chain
tension regularly, as the chain stretches
when it heats up.
ADJUSTING THE CHAIN

16
16
2
1
12
18V18V 58V
2
1
1
2
4
3
1
2
NOTE: Prepare the chain and bar.
Make sure that the chain follows the
correct direction as shown.
REPLACING THE CHAIN AND BAR
NOTE: Refer to the Replacement Parts
section on page 23 for the correct
chain and bar replacements.
NOTE: Dispose the used chain and bar
correctly.

17 17
2
1
12
18V18V 58V
2
1
1
2
4
3
1
2
1
5
6
7
8
1
23
1
2
2
3
NOTE: Prepare the chain and bar.
Make sure that the chain follows the
correct direction as shown.
NOTE: Dispose the used chain and bar
correctly.

18
18
3-4 mm
1
2
9
2
1
10
2
1
12
18V18V 58V
2
1
CLEANING THE PRODUCT

19 19
3-4 mm
1
2
9
2
1
10
2
1
12
18V18V 58V
2
1
NOTE: Clean all foreign material from
the product using a soft brush or cloth.
WARNING: Keep the product away
from corrosive agents, such as garden
chemicals and de-icing salts.
CLEANING THE PRODUCT

20
20
2
1
12
18V18V 58V
1
2
3
1
2
3
NOTE: Store the product in a cool,
dry, and well-ventilated place that
is inaccessible to children. Keep the
product away from corrosive agents,
such as garden chemicals and de-icing
salts. Do not store the product outdoors.
STORING THE PRODUCT
NOTE: Empty the chain oil tank after use
to prevent leakage.