AEMC instruments 6526 User manual

Megohmmeter
Models 6526 & 6534
User Manual
ENGLISH
WITH AEMC
®
INSTRUMENTS
MEGOHMMETERS

Copyright©Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments. All rights reserved.
No part of this documentation may be reproduced in any form or by any means (including electronic
storage and retrieval or translation into any other language) without prior agreement and written consent
from Chauvin Arnoux®, Inc., as governed by United States and International copyright laws.
Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments
15 Faraday Drive • Dover, NH 03820 USA
Tel: [phone] or [phone] • Fax: [phone]
This documentation is provided “as is,” without warranty of any kind, express, implied, or otherwise.
Chauvin Arnoux®󰀨
but does not warrant the accuracy or completeness of the text, graphics, or other information contained
in this documentation. Chauvin Arnoux®, Inc. shall not be liable for any damages, special, indirect,


user of the documentation has been advised of the possibility of such damages.

Statement of Compliance
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments

using standards and instruments traceable to
international standards.
We guarantee that at the time of shipping your

An NIST traceable certicate may be requested
at the time of purchase, or obtained by returning
the instrument to our repair and calibration
facility, for a nominal charge.
The recommended calibration interval for this
instrument is 12 months and begins on the date of
receipt by the customer. For recalibration, please
use our calibration services. Refer to our repair and
calibration section at www.aemc.com.
Serial #:
Catalog #: 2155.53 / 2155.55
Model #: 6526 / 6534
ll in the appropriate date as indicated:
Date Received:
Date Calibration Due:
Chauvin Arnoux®, Inc.
d.b.a AEMC®Instruments
www.aemc.com

TABLE OF CONTENTS
1. INTRODUCTION ..............................................................7
1.1 PRECAUTIONS FOR USE....................................................8
1.2 RECEIVING YOUR SHIPMENT ...........................................9
1.3 ORDERING INFORMATION...............................................10
1.3.1 Accessories............................................................................ 10
1.3.2 Replacement Parts................................................................ 10
1.4 DESCRIPTION ....................................................................11
1.4.1 Model 6526 (Front)................................................................. 12
1.4.2 Model 6534 (Front) ................................................................ 13
1.5 BACK OF INSTRUMENT ....................................................14
1.6 TERMINALS.........................................................................15
1.7 FUNCTION BUTTONS........................................................15
1.8 LCD DISPLAY ......................................................................16
2. OPERATION ...........................................................................17
2.1 SETTING UP THE INSTRUMENT .....................................17
............................................................ 17
2.1.2 Bluetooth................................................................................ 18
2.1.3 Alarms .................................................................................... 18
2.1.3.1 Activating/Deactivating the Alarm Function ...........................18
2.1.3.2 Setting an Alarm Threshold....................................................19
2.1.3.3 Viewing Alarms.......................................................................19
2.1.4  ....................................................................... 20
2.1. 5 HOLD Function ...................................................................... 21
2.1.6 Backlighting............................................................................ 21
2.1.7 Standby Mode ........................................................................ 21
2.2 TAKING MEASUREMENTS ...............................................21
2.2.1 Voltage Measurement............................................................ 21
2.2.2 Insulation Measurement........................................................ 23
2.2.2.1 TEST Button Operation..........................................................25
2.2.2.2 Timed Tests............................................................................25
2.2.2.3 Remote Control Probe (Optional) ..........................................27
2.2.3 Continuity Measurement ....................................................... 27
2.2.3.1 Lead Compensation ...............................................................28
2.2.3.2 Continuity Measuring .............................................................28
2.2.4 Resistance Measurement...................................................... 30
2.2.5 Capacitance Measurement (Model 6526)............................. 30

2.3 RECORDING DATA.............................................................31
2.3.1 Recording a Measurement .................................................... 31
2.3.2 Viewing Stored Recordings ................................................... 32
2.3.3 Deleting Recordings .............................................................. 33
2.3.3.1 Deleting a Single Recording...................................................33
2.3.3.2 Deleting All Records ..............................................................33
3. TECHNICAL SPECIFICATIONS .......................................... 34
3.1 GENERAL REFERENCE CONDITIONS...........................34
3.2 ELECTRICAL SPECIFICATIONS ......................................34
3.2.1 Voltage Measurement............................................................ 34
3.2.2 Frequency Measurement....................................................... 34
3.2.3 Insulation Measurement ........................................................ 35
3.2.4 Continuity Measurement ....................................................... 37
3.2.5 Resistance Measurement...................................................... 37
3.2.6 Capacitance Measurement (Model 6526)............................. 37
3.2.7 Timer...................................................................................... 38
3.2.8 Storage Memory.................................................................... 38
3.2.9 Bluetooth ............................................................................... 38
3.3 OPERATING ENVIRONMENT...........................................38
3.3.1 Voltage Measurement............................................................ 38
3.3.2 Insulation Measurement ........................................................ 38
3.3.3 Resistance and Continuity Measurement ............................. 40
3.3.4 Capacitance Measurement (Models 6526) ........................... 40
3.4 INTRINSIC UNCERTAINTY AND OPERATING
UNCERTAINTY............................................................................................41
3.5 POWER SUPPLY.................................................................41
3.6 ENVIRONMENTAL CONDITIONS.....................................41
3.7 MECHANICAL SPECIFICATIONS.....................................42
3.8 SAFET Y STANDARDS .......................................................42
4. DATAVIEW® SOFTWARE ..................................................... 43
4.1 INSTALLING DATAVIEW®..................................................43
4.2 MEGOHMMETER CONTROL PANEL...............................44
4.3 CONNECTING TO THE COMPUTER ...............................44
4.3.1 Enabling Bluetooth on the Instrument.................................... 44
4.3.2 Pairing the Instrument to the Computer ................................ 45
4.3.3 Connecting the Instrument with the Control Panel................ 45

5. MAINTENANCE AND TROUBLESHOOTING .....................46
5.1 MAINTENANCE...................................................................46
5.1.1 Cleaning ................................................................................. 46
5.1.2 Replacing the Batteries.......................................................... 46
5.2 TROUBLESHOOTING ........................................................48
5. 2.1 Er ro rs ..................................................................................... 48
5.2.1.1 Voltage Present Before an Insulation Measurement..............48
5.2.1.2 Range Exceeded During an Insulation Measurement ...........48
5.2.1.3 Voltage Present During a Continuity, Resistance, or
Capacitance Measurement (Model 6526)..........................................48
5.2.1.4 Memory Full............................................................................49
5.2.2 Resetting the Instrument ....................................................... 49
5.3 REPAIR AND CALIBRATION.............................................49
5.4 TECHNICAL ASSISTANCE................................................50
5.5 LIMITED WARRANTY ........................................................50
5.5.1 Warranty Repairs ................................................................... 51

Megohmmeter Models 6526 & 6534 - User Manual 7
1. INTRODUCTION
Thank you for purchasing an AEMC®Instruments Megohmmeter Model 6526 or
6534.
For the best results from your instrument and for your safety, read the enclosed
operating instructions carefully and comply with the precautions for use. These

Symbols & Denitions

CAUTION - Risk of Danger! Indicates a WARNING. Whenever this symbol
is present, the operator must refer to the user manual before operation
Indicates a risk of electric shock. The voltage at the parts marked with this
symbol may be dangerous
Important information to acknowledge
The product has been declared recyclable
Ground/Earth
Battery
The voltage on the terminals must not exceed 700 Vt
Remote test probe
Chauvin Arnoux®and AEMC®Instruments have adopted an Eco-Design
approach in order to design this instrument. Analysis of the complete
󰀨
on the environment. In particular this instrument exceeds regulation
requirements with respect to recycling and reuse
This product complies with the Low Voltage & Electromagnetic Compatibility
European directives (73/23/CEE & 89/336/CEE)
In the European Union, this product is subject to a separate collection
system for recycling electrical and electronic components in accordance with
directive WEEE 2002/96/EC
Denition of Measurement Categories (CAT)
CAT IV corresponds to measurements performed at the primary electrical supply
(< 1000 V).
Example: primary overcurrent protection devices, ripple control units, and meters.
CAT III corresponds to measurements performed in the building installation at the
distribution level.
Example: hardwired equipment in xed installation and circuit breakers.
CAT II corresponds to measurements performed on circuits directly connected to
the electrical distribution system.
Example: measurements on household appliances and portable tools.
> 700V

8 Megohmmeter Models 6526 & 6534 - User Manuall
1.1 PRECAUTIONS FOR USE
This instrument is compliant with safety standard IEC 61010-2-030, and the leads
are compliant with IEC 61010-031, for voltages up to 600 V in CAT IV or 1000V
in CAT III.

explosion, destruction of the device, or destruction of the installations.
■Carefully read and understand all precautions for use.
■Be aware of all electrical hazards when using this instrument.
■
protection features.
■The safety of any system in which this instrument is incorporated is the
responsibility of the integrator of the system.
■This instrument can be used on CAT IV installations, for voltages not
exceeding 600 VRMS with respect to ground or 700 VRMS maximum between
terminals.
■Do not use the instrument on networks whose voltage or category exceeds

■Observe all environmental conditions of use (see § 3).
■Except for voltage measurements, take no measurements on electrically “live”
systems.
■Do not use the instrument if it appears damaged, incomplete, or poorly closed.
■Before each use, check the condition of the insulation on the leads, housing,
and accessories. Any part on which the insulation is deteriorated (even
partially) must be set aside for repair or scrapping.
■Using the instrument without its battery compartment cover may result in
electric shock to the user.
■Before using your instrument, ensure it is completely dry.
■Use only the leads and accessories supplied. The use of leads (or other
accessories) of a lower voltage rating or category limits the use of the
instrument/leads (or accessories) combination to the lowest category and
service voltage.
■
behind the physical guards.
■Before removing the battery compartment cover, ensure all measurement
leads and accessories are disconnected. Replace all batteries at once. Use
alkaline batteries.
■Use personal protection equipment where appropriate.
■All troubleshooting and metrological checks must be done by competent,
accredited personnel.

Megohmmeter Models 6526 & 6534 - User Manual 9
PRODUCT PACKAGING (2155.53 / 2155.55)
One of the following:
Megohmmeter Model 6526 - Cat. #2155.53
Megohmmeter Model 6534 - Cat. #2155.55
(1) 4 GB USB Drive with
User Manual &
Dataview®Software
Also Included:
(1) (6) AA Batteries
Soft Carrying Pouch
(7.75 x 9.25 x 2.75) in
Cat. #2119.02
(2) Color-coded Grip Probes
Cat. #2152.26
(Model 6534 Only) (2) Color-coded (Red/Black) Test Leads with
Alligator Clips and (1) Black Test Probe
Cat. #2152.26
1.2 RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with
the packing list. Notify your distributor of any missing items. If the equipment

distributor at once with a detailed description of any damage. Save the damaged
packing container to substantiate your claim.

10 Megohmmeter Models 6526 & 6534 - User Manuall
1.3 ORDERING INFORMATION
Megohmmeter Model 6526 .................................................... Cat. #2155.53
Includes soft carrying pouch, (2) color-coded test leads and alligator clips (red/
black), (1) test probe (black),
(6) AA batteries, quick start guide, and USB drive
with DataView®software and user manual.
Megohmmeter Model 6534 .................................................... Cat. #2155.55
Includes soft carrying pouch, (2) color-coded grip probes (red/black), (2) color-
coded test leads and alligator clips (red/black), (1) test probe (black),
(6) AA
batteries, quick start guide, and USB drive with DataView®software and user
manual.
1.3.1 Accessories
Remote Test Probe.................................................................... Cat. #2155.75
Case - Field Case (Waterproof) ................................................ Cat. #2155.77
Continuity Probe........................................................................ Cat. #2138.54
Probe – Red test probe (1000 V Cat IV, 15 A, UL V2) .............. Cat. #5000.98
1.3.2 Replacement Parts
Carrying Pouch for Megohmmeters, Multimeters, etc. ..............Cat. #2119.02
Probe - Set of 2, Color-coded (Red/Black) Grip Probes ........... Cat. #2152.26
Probe - Black test probe (1000 V Cat IV, 15 A, UL) .................. Cat. #5000.30
Lead - Set of 2, 5 ft silicone color-coded (red/black) with 4 mm
straight/right banana plugs (Rated 1000 V, CAT IV, UL)...........Cat. #5000.94
Clip - Safety Alligator - Black (1000 V CAT IV, 15 A, UL V2) ...Cat. #5000.99
Clip - Safety Alligator - Red (1000 V CAT IV, 15 A, UL V2) ...... Cat. #5100.00
Order Accessories and Replacement Parts Directly Online
Check our Storefront at www.aemc.com/store for availability
Dataview® Software Updates are Available at www.aemc.com

Megohmmeter Models 6526 & 6534 - User Manual 11
1.4 DESCRIPTION
The Megohmmeters Models 6526 and 6534 are portable measuring instruments
with digital displays. They are powered by batteries. These instruments can
check the safety of electrical installations. For example, they can be used to test
new installations before they are powered up, check an existing installation in a
󰀨 The Model 6534 is designed
for applications in the electronics industry, including testing the immunity of walls

Features include:
Model 6526 Model 6534
Insulation test voltages 50, 100, 250,
500, and 1000 V
10, 25, 100,
250, and 500 V
Insulation resistance 10 k 2k
PI and DAR ratios calculation 
Continuity measurement  
Resistance measurement  
Programmable alarms  
Frequency measurement 
Capacitance measurement 
Distance measurement
Data storage  
Bluetooth communication  

12 Megohmmeter Models 6526 & 6534 - User Manuall
1.4.1 Model 6526 (Front)
SET-UP
V
OFF
Ω
250V
500V
1000V
MΩ
V
kΩ
MR -
OFF
Ω
100V
250V
500V
1000V
50V
TEST
HOLD
0
MEGOHMMETER
MODEL 6526
G nF
µF
M
VDC
AC
k
<
>
ALARM
MEM
DARPI T1T2
k
M mAµA
G VHz
%
G
M
HOLD P
REL
CLR
REL
G
M
VDC
AC
k
M mAµA
G VHz
%
G
M
HOLD P
<
ALARM
1
2
3
4
5
Figure 1
1. Input terminals
2. Blue backlit LCD
3. Six function buttons (see § 1.7)
4. TEST button to start insulation measurements (see § 2.2.2.1)
5. Eleven-position rotary switch to choose the function or to turn the
instrument OFF

Megohmmeter Models 6526 & 6534 - User Manual 13
1.4.2 Model 6534 (Front)
SET-UP
V
OFF
Ω
250V
500V
MΩ
V
kΩ
OFF
Ω
100V
50V
MR -
OFF
10V
100V
250V
500V
25V
TEST
HOLD
0
MEGOHMMETER
MODEL 6534
G nF
µF
M
VDC
AC
k
<
>
ALARM
MEM
DARPI T1T2
k
M mAµA
G VHz
%
G
M
HOLD P
REL
CLR
REL
G
M
VDC
AC
k
M mAµA
G VHz
%
G
M
HOLD P
<
ALARM
1
2
3
4
5
Figure 2
1. Input terminals
2. Blue backlit LCD
3. Six function buttons (see § 1.7)
4. TEST button to start insulation measurements (see § 2.2.2.1)
5. Ten-position rotary switch to choose the function or to turn the instrument
OFF

14 Megohmmeter Models 6526 & 6534 - User Manuall
1.5 BACK OF INSTRUMENT
1
2
3
4
5
Figure 3
1. Captive quarter-turn screw
2. Battery compartment cover
3. Mounting magnets, moulded into instrument case
4. Non-skid pads
5. Stand

Megohmmeter Models 6526 & 6534 - User Manual 15
1.6 TERMINALS
> 700V
600V CAT IV
Figure 4
The instrument has one positive ( + ) terminal and one negative ( - ) terminal. The
negative terminal also supports the remote probe accessory (see § 2.2.2.3).
1.7 FUNCTION BUTTONS
In general, each button has two functions. One is marked on the button, and is
enabled via a short press. The second function is marked under the button, and
is enabled by a long (>2 seconds) press.
BUTTON DESCRIPTION
Selects the , , PI, and DAR functions (§ 2.2.2.2).
Toggles backlighting ON and OFF (§ 2.1.6).
HOLD Freezes/unfreezes the displayed measurement on the LCD (§ 2.1.5).
SET-UP Accesses the instrument’s setup parameters and information (§ 2.1.1).
0
Applies lead compensation in continuity testing (§ 2.2.3.1).
Activates/deactivates alarms (§ 2.1.3).
and 
The and buttons allow you to:
■Modify the display and program the durations of insulation
measurements (§ 2.2.2.2).
■Choose the continuity test current (§ 2.2.3).
■Program the alarm thresholds (§ 2.1.3).
∆Rel 󰀨
reference measurement (§ 2.1.4).
MEM Records measurements (§ 2.3).
CLR Erase recorded measurements (§ 2.3.3).
Enable Bluetooth wireless communication (§ 2.1.2).

16 Megohmmeter Models 6526 & 6534 - User Manuall
1.8 LCD DISPLAY
Figure 5
1. Logarithmic bar graph displays insulation measurements
2. Secondary display area
3. Main display area
4. Icons/indicators
When the measured value is below the minimum, the instrument displays - - - - .

positive and negative limits, the instrument displays OL or – OL.
G nF
µF
M
VDC
AC
k
<
>
ALARM
MEM
VAR
DARPI T1T2
k nF/ km
M mAµA
G VHz
%
G
M
HOLD
REL
P
1
2
3
4

Megohmmeter Models 6526 & 6534 - User Manual 17
2. OPERATION
NOTE: Except when measuring voltage, all measurements must be
󰀨
no voltage on the system under test before making a non-voltage
measurement. When the rotary switch is set to the voltage or an
insulation testing position, the instrument measures and displays any
voltage present at the input terminals prior to the user pressing the test
button.
2.1 SETTING UP THE INSTRUMENT
2.1.1 Conguration Settings
A >2 second press of the SET-UP button enables you to change


In Set-Up mode, the button performs the following functions:
1st press on The alarm buzzer is active. To deactivate it:
1. Press . On will blink to indicate it is
selected.
2. Press to change the setting to OFF.
3. Press to validate the change.
The symbol disappears from the display
when you exit Set-Up.
Note that this setting reverts to On when you
turn OFF the instrument.
2nd press on 
P
Automatic switching to standby mode is
activated. To deactivate it:
1. Press to select OFF (the setting blinks).
2. Press to change the setting to On.
3. Press to validate the change.
The
P
symbol appears on the display
when you exit Set-Up.
Note that this setting reverts to OFF when
you turn OFF the instrument.
3rd press on Displays the instrument model number.

SET-UP
> 2s

18 Megohmmeter Models 6526 & 6534 - User Manuall
4th press on 
5th press on Displays the instrument hardware version.
6th press on 
2.1.2 Bluetooth
The instrument includes built-in Bluetooth class II capability. This enables you
to connect the instrument to a computer and then communicate with it via the
DataView Megohmmeter Control Panel software (see § 4.3).
Connecting the instrument to a computer is a three-step process:
1. Enable Bluetooth on the instrument (§ 4.3.1).
2. Pair the instrument to the computer using Bluetooth (§ 4.3.2).
3. Connect the instrument to the computer through the DataView
Megohmmeter Control Panel (§ 4.3.3).
2.1.3 Alarms
The instrument includes an alarm function that sounds an audible buzzer when a

2.1.3.1 Activating/Deactivating the Alarm Function
The alarm is available in insulation, resistance, and continuity
measurement modes. Pressing the button activates the
alarm. The symbol is displayed, along with the threshold
value.
To turn OFF the alarm buzzer while it is sounding, press the HOLD button.
To deactivate an active alarm function, press the button.

ALARM
<

Megohmmeter Models 6526 & 6534 - User Manual 19
2.1.3.2 Setting an Alarm Threshold
While is displayed indicating the alarm function is active, you can change
the alarm threshold by pressing the button (except during insulation

values:
■
■
■Insulation:







In each measurement mode, the third threshold can be replaced by a user-

1. Press the button while the threshold value is displayed.
2. 
button. This symbol indicates the direction of the alarm threshold: < for a
low threshold and > for a high threshold.
3. To change the threshold setting, press the 
digit, and then use the button to change its value.
4. Use the and buttons to select and change the other digits in the
threshold value, as well as the units of measurement.
5. button to validate the
setting.
2.1.3.3 Viewing Alarms
When the measurement is below a low alarm threshold or above a high alarm
threshold, the instrument emits a continuous audible signal and the LCD
indicates the threshold crossed:
ALARM <
M
ALARM
k
M
>

20 Megohmmeter Models 6526 & 6534 - User Manuall
When checking continuity, this enables you to determine whether or not the

the display. You can similarly check insulation quality.
2.1.4 ∆REL Function
For an insulation, resistance, or capacitance measurement, you

󰀨
To activate this function, take a measurement, and then press the
∆REL button. This measurement becomes the reference (Rref)
and will be stored and subtracted from subsequent measurement
values (Rmeas). The ∆REL symbol appears on the LCD while this
function is activated.
If the measured value is less than the stored value, the display becomes
negative.
󰀨
() by pressing the button until the % sign appears:

CLR
REL
M
REL
V
G
%
M
REL
G