Aeroflex 3030 Series User manual

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra

3030 RF Digitizer
PXI Module
Operating Manual
Document no. 46892/639
Issue 11
20 October 2008
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PREFACE
ii
About this manual
This manual applies when the instrument is used with the supplied software.
It explains how to set up and configure an Aeroflex 3030 RF digitizer PXI module. Where
necessary, it refers you to the appropriate installation documents that are supplied with the
module.
This manual provides information about how to configure the module as a stand-alone device.
However, one of the advantages of Aeroflex 3000 Series PXI modules is their ability to form
versatile test instruments, when used with other such modules and running 3000 Series
application software.
Getting Started with afDigitizer (supplied on the CD-ROM that accompanies each module
(see Associated documentation)) explains how to set up and configure a 3030 Series RF
digitizer with a 3010 Series RF synthesizer module to form a high performance digitizer
instrument. Using the digitizer soft front panel and/or dll or COM object supplied, the
modules form an instrument that provides the functionality and performance of an integrated,
highly-specified RF digitizer, but with the adaptability to satisfy a diverse range of test or
measurement requirements.
© Aeroflex International Ltd. 2008
No part of this document may be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying,
or recorded by any information storage or retrieval system,
without permission in writing by Aeroflex International Ltd.
(hereafter referred to throughout the document as ‘Aeroflex’).
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PREFACE
iii
Intended audience
Users who need to install and configure the 3030 RF digitizer to down-convert and digitize
RF signals.
This manual is intended for first-time users, to provide familiarity with basic operation.
Programming is not covered in this document but is documented fully in the help files that
accompany the drivers and associated software on the CD-ROM.
Driver version
This PXI RF module is designed to be used with the latest software driver version supplied on
the Aeroflex 3000 Series PXI Modules CD-ROM part no. 46886/028. Operation with earlier
versions of driver software may not be supported.
Associated documentation
The following documentation covers specific aspects of this equipment:
PXI Modules CD-ROM Part no.
46886/028 Compilation containing soft front panels, drivers, application software, data sheets, getting started
and operating manuals for this and other modules
in the 3000 Series.
3000 Series PXI
Modules Common
Installation Guide
Part no.
46882/663 Detailed information on installing modules into a rack, external connections, powering up and
installing drivers.
3000 Series PXI
Modules Installation
Guide for Chassis
Part no.
46882/667 Explains how to set up a populated chassis ready for use.
PXI Studio User Guide Part no:
46892/809 Setting up and using the universal PXI application for system configuration and operation.
Getting Started with
afDigitizer Part no.
46892/676 Setting up and using the RF digitizer application for the 3010 Series and 3030 Series modules.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PREFACE
iv
Preface
The PXI concept
VXI and GPIB systems meet the specific needs of instrumentation users but are often too
large and expensive for mainstream applications. PC-based instrumentation may cost less but
cannot meet the environmental and operational requirements of many systems.
PXI (PCI Extensions for Instrumentation) is based on CompactPCI, itself based on the PCI
standard. PCI was designed for desktop machines but CompactPCI was designed for
industrial applications, and features a rugged Eurocard format with easy insertion and
removal. PXI adds to the CompactPCI specification by defining system-level specifications
for timing, synchronization, cooling, environmental testing, and software. While PXI extends
CompactPCI, it also maintains complete interoperability so that you can use any CompactPCI-
compliant product in a PXI system and vice versa. PXI also makes use of Windows software,
VXI timing and triggering, and VXIplug&play instrument drivers to provide powerful and
affordable systems.
®is a registered trademark of Aeroflex International Inc. in the US
PXI™ is a registered trademark of the PXI Systems Alliance
Windows™, Windows XP™ and Windows NT™ are trademarks of Microsoft Corporation
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PREFACE
v
Abbreviations/acronyms
ACPR Adjacent Channel Power Ratio
ADC Analog-to-Digital Converter
AM Amplitude Modulation
ARB Arbitrary Waveform Generator
CW Continuous Wave
DAC Digital-to-Analog Converter
dB Decibels
dBc Decibels relative to the carrier level
dBm Decibels relative to 1 mW
FFT Fast Fourier Transform
FM Frequency Modulation
FPGA Field Programmable Gate Array
GND Ground
LO Local Oscillator
LVDS Low-Voltage Differential Signaling
PCI Peripheral Component Interconnect
Pk-Pk Peak-to-Peak
PXI PCI eXtensions for Instrumentation
RF Radio Frequency
RMS Root Mean Square
SCSI Small Computer Serial Interface
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PREFACE
vi
SFP Soft Front Panel
SMA SubMiniature version A (connector)
TRIG Trigger
TTL Transistor-Transistor Logic
UUT Unit Under Test
VCO Voltage-Controlled Oscillator
VSWR Voltage Standing-Wave Ratio
VXI VMEbus Extension for Instrumentation
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

1-1
Chapter 1 GENERAL INFORMATION
Introduction
Welcome to the operating manual for the 3030 RF Digitizer PXI module.
The 3030, when used with a 3010 Series PXI RF synthesizer module, forms a compact RF
digitizer that occupies only three slots in a 3U PXI chassis.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

GENERAL INFORMATION
1-2
Applications
The 3030 down-converts and digitizes RF signals. It converts an analog RF waveform
presented at its RF port into a series of amplitude- and phase-corrected digital IF or IQ data
pairs at its LVDS port. Software supplied with the module allows for spectrum analysis of the
digitized signals.
The 3030 can be used in RF test and measurement systems used in development or
manufacturing. Applications span all areas of UHF radio communications.
Wide frequency coverage
The 3030 provides continuous frequency coverage from 330 MHz to 3 GHz. A linear single-
stage down converter frequency converts to an IF centered on 46.08 MHz.
Input range and accuracy
Input level control is provided by electronic switched attenuation, which helps to maximize
the usable dynamic range. Good level accuracy and repeatability make the 3030 ideal for
high-volume manufacturing.
Wide bandwidth
The 3030 produces a 20 MHz wide digitized IF signal. Full-rate digital IF or decimated IQ
data can be output via LVDS, useful for real-time emulation. Data can also be captured to
internal memory and read over the PCI bus.
For narrowband signal analysis, the 3030 provides internal digital downconversion and
decimation. Lowering the sample rate allows longer events to be captured. The 3030
contains digital resampling filters that allow you to set the sample rate, as well as numerous
preset values associated with common digital communications standards.
Signal routing
A configurable routing matrix provides flexibility in how you interconnect signals on the PXI
backplane and the LVDS front-panel input. Predefined routing scenarios can be selected, or
user-defined matrix settings stored and recalled.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

GENERAL INFORMATION
1-3
Triggering and synchronization
The 3030 synchronizes to an external 10 MHz signal (generally supplied by the 3010/3011 RF
Synthesizer). Triggering is external, from the PXI backplane or directly from the front-panel
LVDS connector, or internal, from the internal timer or level trigger.
Software
The 3030 is supplied with a VXI PNP driver and soft front panel for use as a self-contained
module. An instrument-level digitizer soft front panel, dll and COM object are also supplied:
these allow you to use the 3030 together with a 3010 or 3011 RF Synthesizer. Refer to
Getting Started with afDigitizer (part no. 46892/676), supplied on the PXI Modules CD-ROM
part no. 46886/028. An FFT spectrum analyzer measurement suite is supplied, and optional
signal analysis components are available to measure power, modulation quality and spectra to
recognized standards.
PXI Studio, also supplied with the module, configures your PXI modules as logical
instruments using an intuitive and powerful graphical interface. Currently, PXI Studio
provides comprehensive signal generator, digitizer and spectrum analyzer applications and
further development will provide analysis plugins to suit any modulation scheme.
RF Investigator, also supplied with the module, is an application that provides combined
operation of all Aeroflex 3000 Series modules from a single user interface, especially useful
for acceptance testing.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

GENERAL INFORMATION
1-4
Deliverable items
• 3030 RF Digitizer PXI module
• PXI Modules CD-ROM part no. 46886/028, containing soft front panels, drivers,
application software, data sheets, getting started and operating manuals for this and other
modules in the 3000 Series
• 3000 Series PXI Modules Common Installation Guide, part no. 46882/663
• 3000 Series PXI Modules Installation Guide for Chassis, part no. 46882/667
• SMA connector cable, part no. 43139/590 (2 off)
Cleaning
Before commencing any cleaning, switch off the rack and disconnect it from the supply. You
can wipe the front panel of the module using a soft cloth moistened in water, taking care not
to wet the connectors. Do not use aerosol or liquid solvent cleaners.
Putting into storage
If you put the module into storage, ensure that the following conditions are not exceeded:
Temperature range: −20 to +70°C (−4 to +158°F)
Humidity: 5 to 93%, non-condensing
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

2-1
Chapter 2 INSTALLATION
WARNING
Initial visual inspection
Refer to the 3000 Series Common Installation Guide 46882/663.
Handling precautions
Refer to the 3000 Series Common Installation Guide 46882/663.
Hardware installation
Installing the module into the PXI chassis
Refer to the 3000 Series Common Installation Guide 46882/663 and Installation Guide for
Chassis 46882/667.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

INSTALLATION
2-2
Connector care and maintenance
How to connect and torque an SMA connector
1 First, ensure that the mating halves of the connector are correctly aligned.
2 Next, engage the threads of the nut and tighten it by hand, ensuring that the mating halves
do not move relative to each other.
3 Then use a torque spanner to tighten the connector, in order to ensure consistent matching
and to avoid mechanical stress.
Torque settings for connectors are:
0.56 Nm test torque (development use, semi-permanent installations)
1 Nm final torque (permanent installations)
Never use pliers to tighten connectors.
Maintenance
SMA
Clean connectors regularly, using a cotton bud dipped in isopropyl alcohol. Wipe within the
connector cavity, then use a dry cotton bud to finish off. Check for any deposits.
Do not use other cleaners, as they can cause damage to the plastic insulators within the
connectors.
Cap unused connectors.
PCI
Protect PCI connector pins by keeping modules in their original packing when not fitted in the
rack.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

3-1
Chapter 3 OPERATION
Front-panel connectors
1 IF IN 46.08 MHz input, −15 to +5 dBm for full-
scale digitizer. SMA socket, 50 Ω.
2 DATA 68-way SCSI connector for LVDS data I/O.
See Appendix A for details.
3 IF OUT 46.08 MHz, nominally −5 dB relative to RF
input, 0 dB attenuation selected. SMA
socket, 50 Ω.
4 10 MHz I/O Two SMA I/O sockets in parallel.
Input
Frequency standard input for sampling
clock. 50 Ω. 0.4 to 4 V pk-pk.
Output
Link-through from input.
5 LO IN 1.5 to 3 GHz, nominally 0 dBm. SMA
socket, 50 Ω.
6 RF IN 16 dBm max, 0 dB input atten. SMA socket,
50 Ω.
3030
IF IN
DATA
10 MHz
I/O
LO IN
RF IN
I/P PWR
16dBm MAX
IF OU T
4
1
2
3
5
6
C5874
Fig. 3-1 3030 front panel
Maximum safe powers
RF input: +16 dBm continuous (0 dB input attenuation)
IF input: +10 dBm (0 dB IF attenuation)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

OPERATION
3-2
Soft front panel (af3030_sfp)
The soft front panel provides a graphical interface for operating the module. It is intended for
testing and diagnosing, for demonstration and training, and for basic operation of the module.
It represents most of the functions available in the instrument driver. It is not however a
comprehensive application suitable for measurements; for this, use the afDigitizer DLL or
afcomDigitizer COM object.
Installation
The soft front panel is installed during the driver installation process (refer to the 3000 Series
PXI Modules Common Installation Guide, part no. 46882/663).
Open the AF3030_sfp.exe file: this is in the C:\VXIPNP|WinNT\af3030\ directory on a
Windows NT machine, for example. It is also accessible from the Windows Start menu under
Programs\Aeroflex\PXI Module Front Panels\AF3030 Front Panel. The soft front panel,
similar to that in Fig. 3-2, is displayed.
Detailed help information
Soft front panel controls are all available as driver export functions unless noted otherwise,
and are documented in the help files. This operating manual provides an overview of the
facilities that the module provides and summarizes its operation; however, refer to the help
files for detailed descriptions of functions together with their parameter lists and return values.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

OPERATION
3-3
C6188
IF/IQ data format
Menu bar
Input
source
Boot
RF tuning Input conditioning
Acquisition &
triggering
Fig. 3-2 3030 soft front panel
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

3-4
Soft front panel controls
Menu bar
File
Save Captured Data (as ASCII file)… captures the 16-bit sample data into the specified
ASCII file.
Save Captured Data (as Binary file)… captures the 16-bit sample data into the specified
binary file.
Click Exit to close the application.
Settings
Load and Saveallow you to load and save soft front panel configurations from and to your
preferred locations. If you did not change the default location when installing the software, it
is C:\VXIPNP\WinNT\af3030\settings, and configurations are saved as .ini files.
You can edit, copy and paste settings files as required; for example, you may want to
save only a new routing setup without changing other parameters. Edit the saved .ini
file using a text editor (for example, Notepad) to remove unwanted parameters. Ensure
only that you do not delete the General (VendorID, DeviceID) and Version
(Major/Minor) parameters. Save the changed file. When the settings file is next loaded,
the configuration of the soft front panel changes to match the parameters remaining in
the settings file.
Directories lets you choose the location for your front-panel configuration settings.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

MENU BAR ON SOFT FRONT PANEL
3-5
LVDS allows you to set each LVDS Data, Auxiliary and Marker mode for input, output or tri-
state (default) operation.
• To use Spare 0 as a trigger input, set LVDS Data to Input. Spare 0 is controlled by LVDS
Data Mode.
• To use an auxiliary bit as a trigger input, set LVDS Auxiliary to Input
• To use a marker bit as a trigger input, set LVDS Marker to Input.
• IF Data Position places 14-bit IF data in either the upper 14 bits of a 16-bit word (the
lower two bits are padded with 0s) or lower 14 bits of a 16-bit word (upper two bits are
sign extended), as required by the processing software.
Routing Scenarios allows you to select a predefined routing matrix connection. A tick
against the scenario’s title shows that it is selected.
Selecting or removing a routing scenario affects only the connections specific to that scenario,
and does not change any other routing connections. However, changing the routing matrix
connections of any scenario invalidates that scenario.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

MENU BAR ON SOFT FRONT PANEL
3-6
Routing Matrix displays a matrix that provides interconnection between input and output
signals on the PXI backplane bus and the DATA connector, as shown diagrammatically in
Fig. 3-3. This provides great flexibility in how you can route signals between modules.
DATA
3030 PXI MODULE
PXI BACKPLANE BUS
C5980
PXI_STAR
PXI_LBL[0]–[12]
PXI_TRIG[0]–[7]
LVDS_MARKER1–4
LVDS_AUX[0]–[4]
LVDS_SPARE[0]–[2]
ROUTING MATRIX
Fig. 3-3 Routing matrix in 3030
Use the matrix (Fig. 3-4) to interconnect signals. Output signals form the body of the matrix.
Select appropriate input signals from the drop-down menus under each down-arrow to create
the interconnections.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

MENU BAR ON SOFT FRONT PANEL
3-7
Check the boxes to enable the outputs and select the appropriate LVDS mode.
Reset connects all input signals to GND and disables the outputs (LVDS outputs go tri-state).
This is the default state.
When operating the 3030 in default digitizer mode (routing matrix reset), all necessary input,
output and trigger signals are available on front-panel LVDS and SMA connectors and there is
no need to configure the matrix. If you need to set up particular signal routings, you can
define these using the drop-down menus on the matrix and save them using the Load and
Savecommands in Settings, or use Routing Scenarios to access pre-set alternative routings,
or contact Aeroflex if you need assistance in defining particular routing requirements.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com