AeroPure AP80RVL User manual

MODEL: AP80RVL
BATHROOM FAN
www.aeropurefans.com
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, PLEASE READ THE FOLLOWING:
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. This product is designed for installation
in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must be horizontal. ** DO NOT MOUNT THIS PRODUCT IN A WALL.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. Please read
specification label on product for further information and requirements.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance lower or remove grille and vacuum interior of unit with the
dusting brush attachment.
The motor is permanently lubricated and never needs oiling.
OPERATION
Use an on/off switch to operate this fan. See “Connect Wiring” for details.
PLAN THE INSTALLATION
1. Do not use in a cooking area.
2. Two ways to connect ductwork to a factory-shipped unit.
INSULATION*
(Place around and
ROOF CAP*
over Fan Housing.)
(with built-in
damper)
FAN
POWER
HOUSING
CABLE*
Keep duct
runs short
Seal gaps
around
Housing.
ROUND
DUCT*
WALL CAP*
Seal duct
(with built-in
*Purchase
joints with
ROUND
damper)
separately
tape.
ELBOW(S) *
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
1.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number
listed in the warranty. 2.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power
from being switching on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel. 3. Installation work and electrical wiring must be done by a licensed person(s) in accordance with all applicable codes and
standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through
the flue (chimney) of fuel burning equipment to prevent backdraft. Follow the heating equipment manufacturer’s guideline and safety standards such
as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden
utilities. 6. Ducted fans must always be vented to the outdoors. 7. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault
Circuit Interrupter) - protected branch circuit. 8. This unit must be grounded. 9. Never place a switch where it can be reached from a tub or shower.
10. Not for use in kitchens. 11. Install fan at least 2.5 m (8.2 feet) above the floor. 12. WARNING: To reduce the risk of fire or electric shock,
do not use this fan with any solid-state speed control device. 13. The fan must not be installed in a ceiling thermally insulated to a value greater than
R40.

ASSEMBLY INSTRUCTIONS
1. Before installation, you need to know:
Screw A
ST4.2*1/2"
Screw B
ST4.2*1"
Hanger bar
13 3/8"
(long)
14 3/8 in.-23 1/2 in. (365-597)
1. MOUNT WITH HANGER BARS
1a. Sliding hanger bars have been provided, which allow the housing to
be positioned accurately anywhere between the framing. The bars may
be used on all types of framing: I-joist, standard joist, and truss
construction. Slide hanger bars onto housing and adjust as needed to fit
between framing.
1b. Extend the hanger bars to the width of the framing. Position the
Screw A
fan with the hanger bar tabs aligned with the bottom edge of the framing,
holding the ventilator in place.
Secure hanger bars to framing using one screw on each end of hanger
bar. Attach set screws to lock bar hangers in place.
Screw B
2. INSTALL ROUND DUCTWORK
Connect the round ductwork (not included) to the damper/duct connector,
and run the ductwork to a roof or wall cap (not included). Using duct tape
(not included), secure all the ductwork connections so that they are air
tight. Insulated flexible duct is recommended for the quietest possible
installation. A 1 –3 foot run of rigid duct- followed by insulated flexible
duct- will ensure quietest operation.
CONNECT ELECTRICAL WIRING
Run 120 Volts AC house wiring to the fan. Use only UL-approved connectors (not included) to attach the house wiring to the
wiring plate. Refer to the wiring diagram, and connect the wires as shown.
BLACK(BLK)
WHITE(WHT)
BLUE(BLU)
GROUND (GRD)
LIGHT
WIRE PANEL
UNIT
FAN
SWITCH BOX
FAN
LIGHT
RECEPTACLE
RECEPTACLE
POWER SUPPLY
120V AC
2
Aero Pure AP80RVL

READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
FINISH CEILING WORK
1. A round ceiling hole 6 1/2 inches (165mm) diameter should be cut.
Seal any gap between the hole in the drywall and the fan with sealant.
2. Install the compact florescent bulb or LED bulb. Bulb not included.
3. The bulb housing can adjust up or down to accommodate different
bulbs. Unit is qualified with use of G24 adaptor and use of a GU24
bulb.
Lamp base
Wing nut
.
Fluorescent lamp
Joist
Hanger
bar
Ceiling
After finishing the ceiling job, fill gap between flange and ceiling with
caulk or other sealant to prevent air leakage.
REPLACEMENT INSTALLATION
1. Remove the trim ring by detaching the springs.
2. Remove the screws as shown in the right.
3. Remove the lamp base.
4. Pull the duct system so that you can see the blower
system.
Remove the screws
Blower system
Lamp base
REPLACEMENT INSTALLATION
5. Remove the screws as shown on the right.
Remove the screws
6. Remove the blower system from of the housing.
7. Replace the broken parts.
Remove the screws
REPLACEMENT INSTALLATION
8. To replace the capacitance remove the wire panel, and then
replace the capacitance.
Remove
the screws
Wire Panel
3
Aero Pure AP80RVL

SERVICE PARTS
PART
PART NAME
Qty.
12
1
Trim Ring
1
6
2
Grille Spring
2
11
3
Lamp base
1
5
4
Wire Panel / Harness Assembly
1
5
Hanger Bars
4
5
6
Wiring plate
1
7
Motor
1
4
10
8
Motor plate
1
9
Blower Wheel
1
9
10
Blower housing
1
3
11
Duct
1
8
2
12
Housing
1
1
7
WARRANTY
4
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
This warranty covers all defects in workmanship or materials for:
The mechanical and electrical parts contained in this product for a period of 72 months from the date of purchase. You
must keep and be able to provide your original sales receipt as proof of date of purchase. This warranty is covered to the
original retail purchaser of this product only. The manufacturer will replace any mechanical or electrical part that proves
defective in normal household use for a period of 72 months.
THIS WARRANTY DOES NOT COVER:
• Damages from improper installation.
• Damages from shipping.
• Damages from misuse, abuse, accident, alteration, lack of proper care and maintenance.
• Damages from service by persons other than a licensed electrician.
• Does not cover any labor or transportation charges related to the repair of this product.
This warranty does not extend to fluorescent lamp starters and tubes or any light bulbs..
THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
THE WARRANTIES OF MERCHANTABILITYAND FITNESS FOR APARTICULAR PURPOSE.
The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty does not
cover incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you. Some states do not allow limitations on how long an implied warranty
lasts, so this limitation may not apply to you. This warranty gives you specific legal rights; you may also have other rights
that vary from state to state.
Aero Pure AP80RVL