AeroPure CP80S Series User manual

BATHROOM FAN
MODEL: CP80-S Series
APPROVED FOR BOTH CEILING AND WALL INSTALLATION
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, PLEASE READ THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or
telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switching on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must
be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and
standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning
equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire ProtectionAssociation (NFPA), and theAmerican Society for Heating, Refrigeration andAir
Conditioning Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. Acceptable for use over a tub or
shower when connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit (ceiling installation only). 8. This unit
must be grounded. 9. Not for Use in Kitchens.
10. To reduce risk of fire and to properly exhaust air, be sure to duct air outside –Do not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces, or garages. 11. WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan
With Any Solid-State Speed Control Device. 12. The fan must not be installed in a ceiling thermally insulated to a value greater R40.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. This product is designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point up for wall
application.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall and construction dust away of motor unit.
4. Please read specification label on product for further information and requirements.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance, lower or remove grille and vacuum interior of unit with the
dusting brush attachment.
The motor is permanently lubricated and never needs oiling.
OPERATION
Use an on/off switch to operate this fan. See “Connect Wiring” for details.
PLAN THE INSTALLATION
1. Do not use in a cooking area. 2. Two ways to connect ductwork to a factory-shipped unit
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner
Aero Pure CP80-S

TYPES OF TYPICAL INSTALLATIONS
1. Housing mounted to I-joists (Start at “ASSEMBLY INSTRUCTIONS 1”)
2. Housing mounted to joists (Start at “ASSEMBLY INSTRUCTIONS 1” )
3. Housing mounted to truss (Start at step “ASSEMBLY INSTRUCTIONS 2”)
ASSEMBLY INSTRUCTIONS
1.MOUNT HOUSING TO JOIST OR I-JOIST.
Hold the housing so that it is in contact with the bottom of the joist.
Place the fan housing next to the ceiling joist. Using wood screws
attach the housing loosely to the ceiling joist through the keyholes
in the mounting tabs.Adjust the housing to be flush with the
finished ceiling. For the grille to fit properly, the housing’s rim must
not extend beyond the finished ceiling surface. When the housing
is correctly adjusted, tighten the screws in the slots.
2. MOUNT WITH HANGER BARS
Insert the hanger bars into the slots in the housing. Place the fan
housing between the joists, make sure the bottom of the housing
is even with the finished ceiling. Extend the hanger bars to the
joist. Use screws to secure the hanger bars to the
ceiling joists.
3. ATTACH DAMPER/DUCT CONNECTOR
Snap the damper/duct connector onto the fan housing. The
connector must be flush with the top of the housing, and the
damper flap should fall closed.
4. INSTALL ROUND DUCTWOTK
Connect the round ductwork (not included) to the damper/duct
connector,and run the ductwork to a roof or wall cap (not included).
Using tape (not included), secure all the ductwork connections so
that they are air tight.
For Model CP80-S:
The ducting from this fan to the outside of building has a strong effect on
the air flow, noise and energy use of the fan. Use the shortest, straightest
duct routing possible for best performance, and avoid installing the fan with
smaller ducts than recommended. Insulation around the ducts can reduce
energy loss and inhibit mold growth. Fans installed with existing ducts may
not achieve their rated air flow.
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner
2
Aero Pure CP80-S

CONNECT ELECTRICAL WIRING
Run 120V AC house wiring to the location of the fan. Use only UL-approved connectors (not included) to attach the house wiring to
the wiring plate. Refer to the wiring diagram and connect the wires as shown.
INSTALL GRILLE
Install ceiling material to complete the ceiling construction. Then, cut
around the fan housing.
To attach the grille assembly to the fan housing, pinch the grille springs on
the sides of the grille assembly, and position the grille into the housing with
the grille springs in the appropriate slots. Push the grille assembly towards
the ceiling to secure.
SERVICE PARTS
* Blower Assembly includes part 5, 4, d, 3, c, b, a.
Replacement installation: a
Remove the screw (part c), then take out the motor plate (part 3) from
the housing (part 9) by pushing down the rib in the plate while pulling
out on the side of the housing. Replace the broken parts.
WARNING: Before replacing, be sure to turn off power at power source.
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner
3
Aero Pure CP80-S
PART
PART NAME
Qty.
1
Grille Assembly (includes part 2)
1
2
Grille Spring
2
3
Motor Plate
1
4
Wire Panel / Harness Assembly
1
5
Motor
1
6
Blower Wheel
1
7
Hanger Bars
4
8
Housing
1
9
Wiring plate
1
10
Damper / Duct Connector
1
a
Screw
1

WARRANTY
This warranty covers all defects in workmanship or materials for:
The mechanical and electrical parts contained in this product for a period of 72 months from the date of purchase. You must keep
and be able to provide your original sales receipt as proof of date of purchase. This warranty is covered to the original retail
purchaser of this product only. The manufacturer will replace any mechanical or electrical part that proves defective in normal
household use for a period of 72 months.
THIS WARRANTY DOES NOT COVER:
•Damages from improper installation.
•Damages from shipping.
•Damages from misuse, abuse, accident, alteration, lack of proper care and maintenance.
•Damages from service by persons other than a licensed electrician.
•Does not cover any labor or transportation charges related to the repair of this product.
This warranty does not extend to fluorescent lamp starters and tubes.
THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE.
The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty does not cover incidental
or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so this limitation may not
apply to you.
Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you. This warranty
gives you specific legal rights; you may also have other rights, which vary from state to state.
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner
4
Aero Pure CP80-S