AERTECNICA TUBO CM837 User manual

SPECIFICATIONS
CONFORMITY WITH DIRECTIVE 99/05/EC
The remote control is conform to the essential requirements of Directive 99/05/EC. The
following Technical Standards have been applied to verify the conformity:
EN 60335-1, EN 301489-3, EN 300220-3
1 - remove the dust container of the central vacuum unit.
2 - press the start button (P) on the tube (T) for approximately 25 seconds; the central
vacuum unit will switch off.
3 - press the start button (A) and immediately after button (B) on the remote control
(R) within 5 seconds.
4 - wait 5 seconds to save the settings.
5 - re-fasten the dust container.
The programming has been completed. The central vacuum unit is switched on and
switched off on the exible hose and the remote control by using either button.
Wireless hose Kit CM186 already programmed
Wireless remote control
to be programmed
The central vacuum unit and the wireless receiver must remain connected to the power
supply.
The wireless receiver is powered by 12 volts so no electrical hazard risk exists.
1- check that the connection between the receiver plug line (W) and the central
vacuum unit is correct.
2- Open the receiver (W).
3 - pull the electronic board (C) out.
4 - press the red key (H), and led (K) lights.
5 - press the start button A and immediately after button B on the remote control
within 5 seconds.
6 - wait 5 seconds to save the settings.
7 - insert the electronic board again and close the receiver.
The programming has been completed. The central vacuum unit is switched on and
switched off on the exible hose and the remote control by using either button.
REMOTE CONTROL CM837 with WIRELESS HOSE KIT CM186
REMOTE CONTROL CM837 with WIRELESS RECEIVER KIT CM186
INSTRUCTIONS FOR
WIRELESS REMOTE CONTROL
CM837
OPERATING FREQUENCY
EFFECTIVE RADIO POWER
TYPE OF MODULATION
ABSORPTION IN TRANSMISSION
TYPE OF BATTERY
433,92 Mhz
0,3 mW
amplitude (on off)
10mA
12V alkaline GP23A
TR
P
PROCEDURE A (RECOMMENDED)
PROCEDURE B (IF NECESSARY)
EN
C
K H
R - Wireless remote control CM837
A and B - Buttons for starting/stopping the central
vacuum unit (both the buttons carry out the same
function)
L - start/stop signalling led
A B
L
R
A B
Wireless remote control
to be programmed
WR
Wireless hose Kit CM186
already programmed
A B

Change the battery when the intensity of led (L) on the remote control diminishes and
the transmission eld is notably reduced.
Open the cover (D) on the remote control (R) as shown in the picture.
Replace the battery inside and close the cover again.
1- unscrew the antenna and open the receiver (W).
2 - press and hold down the button (H) on the receiver; the led (K) will switch on for a
few seconds.
3 - when the led (K) switches off release the button (H); the led will start to blink
slowly (1 blink per second). When it has nished 30 blinks, the led (K) stays switched
on.
4 - press the start button (A) and immediately after button (B) on the remote control
(R) within 5 seconds.
5 - wait 5 seconds to save the settings.
6 - re-fasten the receiver and switch the antenna back on.
The programming has been completed. The central vacuum unit is switched on and
switched off on the exible hose and the remote control by using either button.
The central vacuum unit and the wireless receiver must remain connected to the power
supply.
The wireless receiver is powered by 12 volts so no electrical hazard risk exists.
Wireless remote control
to be programmed
REMOTE CONTROL CM837 with WIRELESS RECEIVER KIT CM187
W
CHANGING THE BATTERIES IN THE REMOTE CONTROL
PROCEDURE
C
K
H
Wireless hose Kit CM187
already programmed
R
A B
D
R