AFA Stainless AF2421CS User manual

All-IN-ONE 304 STAINLESS STEEL UTILITY SINK
WITH FAUCET AND DRAIN
AF2421CS
Owners Manual
Español P.14

Owners Manual
2
SAFETY INFORMATION
Caution: Carefully remove the faucet box, sink box
and strainer from cabinet.
Please read and understand this entire manual before
attempting to assemble, operate or install the product. Before
beginning the assembly of this product, compare the parts
with the package contents and parts list. If any part is missing
or damaged do not attempt to assemble the product and
contact AFA Stainless customer service for assistance.
WARNING
• Follow the installation instructions carefully. Proper
installation is the installer’s responsibility.
AF2421CS
DIMENSIONS
This unit meets or exceeds the following:
• ASME A112.18.1/CSA B125.1
• California Title 20 Water-Efficiency Standards
• Listed by CUPC for use in the US and Canada
• Listed by California Energy Commission
Flow rate
1.8GPM (6.8L/M)-MAX ASME A112.18.1/ CSA B125.1
AFA STAINLESS PRODUCT SUPPORT TEAM
Customer service hotline
Toll Free: [phone] English Speaking Only
Monday-Friday 9 a.m-5 p.m Pacific Time Zone
Email: [e-mail]
AFA USA LLC
3190 Airport Loop Dr Ste B1, Costa Mesa, CA 92626

PARTS LIST
Faucet
A-1 Faucet Body
A-2 Mounting Stud
A-3 Gasket
A-4 Mounting Nut
A-5 Hot & Cold Supply Line
A-6 3/16" (5 mm) Set Screw
A-7 Diverter Handle
A-8 Decorative Collar
A-9 Retainer Nut
A-10 Cartridge
A-11 Aerator
Utility Sink
B-1 Sink
B-2 Backsplash
B-3 Leg Collar
B-4 Bracket
B-5 Leg
B-6 Feet Leveler
B-7 Connection pipe
B-8 Connection pipe
B-9 3 Way L Shape Connector
B-10 Two-way Connector
B-11 Anchors
B-12 Screws
B-13 Thread 3/4" female to 3/8"
male adapter
Strainer
D-1 Strainer Basket Assembly
D-2 Strainer Bowl
D-3 Top Gasket
D-4 Bottom Gasket
D-5 Lock Nut
D-1
D-2
D-3
D-4
D-5
A-1
A-2 A-5
A-7A-8A-9A-10
A-6
A-11
A-3
A-4
B-1
B-2
B-3
(×4)
B-5
(×4)
B-6
B-4
B-7
B-8
(×2)
B-9
B-10
(×2)
(×2)
B-11
(×4)
B-12
(×4)
B-13
3

Recommended Tools for Installation:
T-1 (Included)
Important Information
·Before and during installation, please read and familiarize yourself with all installation
instructions for this product.
·Please keep all components, parts and accessories of this product away from small children
and minors. During installation, all screws, tools and small parts should be supervised so that
they do not fall into the hands of children.
·Use caution at all times when installing this product. Please ensure that you are physically able
to perform all parts of the installation and that you have the correct tools and equipment
needed. Before beginning, remove all wrappers and packing materials including staples and
packing straps.
·Please check to ensure that all components and parts are complete.
3/32" (2,5 mm) Allen Wrench
4
T-4
T-5 T-6
T-2 (Included) T-3 (Included)
T-9
5/32" (8 mm) Allen Wrench
T-10 T-11
Plumber Putty
T-7 T-8
Adjustable Wrench
Channel Lock Wrench
Plumber’s Tape
Phillips screwdriverbit
Flathead Screwdriver
1/4 Inch Bit Drill Bit
Phillips Screwdriver
Hammer Pencil

5
Lay Sink (B-1) upside-down.
Insert Legs (B-5) into Leg
Collars (B-3).
CAUTION: Shut off water supply prior to installation.
Tighten screws on each Leg Collar
with Allen Wrench (T-2).
Connect Connection pipe (B-7)
with 3 Way L Shape Connectors (B-9),
and put into the pre-installed legs.
Insert the Connection pipes (B-8)
into 3 way L shape connector (B-9).
Put the 2 way connector (B-10)
into the legs and connect to the
Connection pipe. Tighten the screw
with Allen Wrench (T-3).
Adjust the 3 way L shape connector
(B-9) on the legs and tighten the
screw with Allen Wrench (T-3).
B-9 B-7
B-5
B-3
23
1
B-3
B-5
T-2
B-9
T-3
6
B-8
B-10
45
Optional: Apply a 1/4” bead of
Plumber's putty 1/4” (7 mm) around
the entire sink drain hole as shown
above.

6
Place the Bottom gasket (D-3) on
the underside of the Strainer bowl
(D-2). Place Top gasket (D-4) on
top of Lock nut (D-5) and tighten
to Strainer bowl (D-2) using Channel
lock wrench (T-9). Wipe extra
Plumber's putty away from sink side
of the Strainer bowl (D-2) with a
clean rag.
A-1
A-5
A-3
A-4
A-2
A-1
A-1
A-2
A-5
A-3
A-4
D-2
D-3
D-4
D-5
T-9
D-1
D-2
D-3
D-4
D-5
8
79
11
Carefully move sink against wall
at your desired location. If needed,
use a pencil to mark off mounting
height of Bracket (B-4).Position
Bracket(B-4)on wall, marking off
fastening location on wall through
holes on Bracket (B-4). Drill holes in
marked locations with Philips screwd
driver bit (T-7). Insert Anchor (B-11)
completely into each drilled hole.
Fasten Screws(B-12) through these
holes into wall or anchors tightly
with a screwdriver.
12
10
Open the faucet box and check
all parts.
Prepare strainer for installation.
Loosen the Lock nut (D-5) , check to
ensure that all parts are complete.
Slide hot & cold water supply
lines (A-5) through mounting hole
and position faucet on sink.
From underneath the sink, slide
Gasket (A-3) . Thread the
Mounting nut (A-4) onto the
mounting stud under sink.
B-11
B-12
B-4
T-11
T-10
T-7
T-4

7
Wrap the water on/off valve threads
with one complete revolution of
Plumber’s tape (T-1). Attach cold &
hot supply lines (A-5) to shutoff
valves. Tighten with Adjustable
wrench (T-8) in a clockwise
direction until secure.
3/8" (10mm)
Hot
T-8
A-5
T-1
15
Turn on hot and cold water supply
valve(s) by turning handles counter
clockwise.
Hot
Cold
16
Connect the P-trap (Not included)
to the drain.
14
Turn on faucet and allow water to
flush lines for 5 minutes.
Check for leaks under Strainer (D-2)
and at Faucet connections (A-5)
under the sink.
17
Slightly lift sink and hook flange
of sink over Bracket(B-4). Adjust
Feet Levelers (B-6) to ensure sink
is stable and level.
Note: Bracket is to prevent sink
tipping, NOT for mounting sink to
a wall. Do NOT mount sink to a
wall without legs.
13

8
Connect the garden hose to 3/4" adapter.
And connect the water supplies to 3/8" adapter.
3/4"
B-13

9
CLEANING AND CARE OF AERATOR
23
1
T-8
Remove the Aerator (A-11), use a
soft cloth in the joint of Adjustable
Wrench (T-8) to loosen if needed.
Be careful not to scratch the
faucet finish.
Flush the Aerator (A-11).
A-11
Install the Aerator (A-11).
Use a soft cloth in the joint of the
Adjustable Wrench (T-8) and
tighten Aerator (A-11).

Hot
Cold
A-10
HELPFUL TOOLS
3/32" (2,5 mm)
Allen Wrench
(Included)
Flathead Screwdriver Adjustable Wrench
AFA Stainless is committed to producing the finest Solid Stainless Steel Faucet on the planet. A major component that
is a secret to AFA’s success, has been the long standing relationship with German manufactured Fluhs, the worlds
most advanced leader of high quality, technologically suburb ceramic cartridges guaranteed for life. In the rare case
of cartridge failure, AFA will replace the cartridge at no charge by calling our customer service hotline.
1-877-778-6888.
10
Fluhs cartridge model # BFZU 1700
2
Ceramic cartridge (A-10) is located
inside the diverter.
3
1
Turn off the hot & cold water
supply by turning the water
supply valve(s) clockwise until it
can no longer be turned.
Cover or close the sink drain.
CARE AND REPLACEMENT OF CERAMIC CARTRIDGE
For safety and ease of faucet cartridge replacement,
AFA recommends these tools.

T-5
A-8
T-8
A-9
A-10
3/32"
(2,5 mm)
A-6
T-2
A-7
A-8
11
7
Use Adjustable wrench (T-8) and
unscrew Retainer nut (A-9) counter
clockwise (not the top of the
ceramic cartridge). Set aside.
8
Remove Cartridge (A-10).
9
9
Remove Decorative collar (A-8)
and set aside.
5
If Decorative collar (A-8) is tight
and not easy to remove, use a
Flathead screwdriver (T-5) and
carefully pry off the collar.
Set aside.
6
4
Remove Diverter handle (A-7)
and set aside.
Using 3/32" (2,5 mm) Allen wrench
(T-2 Included) carefully loosen
Set screw (A-6) inside diverter.
(Do not remove screw).

A-10
Hot
Cold
12
10
Turn on hot and cold water supply
valve(s) counter clockwise. Run
water and check for leaks.
11
Install new Cartridge (A-10).
Reassemble faucet by reversing
steps.
– Please ensure that the surface of your AFA product has cooled down before cleaning (clean at room temperature).
– Use a soft cloth (e.g. a micro fibre cloth) to dry the product after every use.
– Do not use abrasive cleaning agents or tools – No scratching of the surface.
– Descaling is an aggressive process for products, so you should only do this when and where it is needed. Please wash the
product thoroughly with clean water after using any cleaning chemicals, then dry it with a soft cloth (e.g. a micro fiber
cloth).
– Do not use acidic or caustic cleaning agents or abrasive sponges.
– Do not use degreasing agents or too much cleaning agent.
– Do not spray directly onto the faucet.
– Do not use hard cleaning tools or materials.
– No scratching of the surface.
CLEANING AND CARE INSTRUCTIONS