aFe Power 77-84013 User manual

Instruction Manual P/N: 77-84013___ SCORCHER BLUE POWER MODULE
Make: Chevrolet Model: Silverado 1500 Year: 19-20 Engine: I4-2.7L(t)
Make: GMC Model: Sierra 1500 Year: 19-20 Engine: I4-2.7L(t)

Page 2
THIS IS A HIGH-PERFORMANCE PRODUCT: Do not use this product until you have carefully read the
following agreement and installation instruction. This sets forth the terms and conditions for the use of
this product. The installation of this product indicates that the BUYER has read and understands this
agreement and accepts its terms and conditions.
DISCLAIMER OF WARRANTY AND LIMITATION OF LIABILITY: Advanced FLOW Engineering, Inc. (also
known as aFe or aFe POWER) and its successors, distributors, jobbers, and dealers (hereafter “SELLER”)
shall in no way be responsible for the product’s improper use and service. It is the installer’s
responsibility to check for proper installation and if in doubt, contact the manufacturer. The SELLER
assumes no liability regarding the improper installation or misapplication of its products. BUYER
acknowledges it has had the opportunity to fully inspect the product. Accordingly, BUYER acknowledges
that the product is being sold in “AS IS/WHERE IS” condition. SELLER shall not be held liable for special,
indirect, incidental or consequential damages of any nature with respect to the products (including,
without limitation, lost profits, lost sales, loss of production, property damage, personal injury or loss or
damage resulting from interruption or failure in operation of the products) and BUYER hereby expressly
waives and disclaims all such liability claims. The BUYER acknowledges and agrees that the disclaimer of
liability contained herein is a material term of the sale of the product and, to the fullest extent permitted
by law, BUYER shall defend, indemnify and hold SELLER harmless from any and all claims, demands,
causes of action, controversies, liabilities, fines, losses, costs and expenses (including, but not limited to
attorneys’ fees, expert witness expenses and litigation expenses) arising from or related to SELLER’s
products.
Before proceeding with the installation:
•Please read the entire instruction manual before proceeding.
•Ensure all components listed are present.
•If you are missing any of the components, call customer support at 951-493-7185.
•Ensure you have all necessary tools before proceeding. Do not attempt to work on
your vehicle when the engine is hot.
Emission Disclaimer: This product is not currently CARB exempt and is not available for
purchase in California or for use on any vehicle registered with the California Department
of Motor Vehicles.

Page 3
Label
Qty.
Description
Part Number
A
1
Module
R77-84013
B
1
LED Switch
05-70029
C
1
Bypass Plug
05-70017
D
1
Harness
AFE-10-248
E
2
Velcro (2” Inches)
05-01244
F
5
Cable Ties
05-60167
G
2
Double Sided Tape
07-90001

Page 4
Refer to Figure A for Step 1
Step 1: Before installing your aFe POWER module, you will have to place your vehicle’s ECU in sleep mode.
In order to do this, you will need to do the following:
•If the engine is cold: open the hood, close the doors, lock the car and wait 30 seconds.
•If the engine is warm: open the hood, close the doors, lock the car and wait 20 minutes.
•If the engine is warm and you can’t wait 20 minutes: disconnect the battery.
DO NOT OPEN VEHICLE DOORS WHILE SENSORS ARE DISCONNECTED OR BEFORE
CONNECTING THE SCORCHER BLUE MODULE. DOING SO WILL TRIGGER A CHECK
ENGINE LIGHT.
Figure A
2
1
REMOVAL

Page 5
Refer to Figure B for Steps 2-3
Step 2: Remove the front dust cover to gain access to the T-MAP sensor. This cover can be removed by
pulling up on the plastic push-clips and removing the hood latch. The cover can now be lifted up and placed
to the side.
Step 3: Locate the T-MAP sensor. It is located on the driver side of the intercooler.
REMOVAL
Figure B

Page 6
Refer to Figure C for Step 4-5
Step 4: Disconnect the T-MAP sensor by pulling back on the locking tab and pressing down on the clip while
sliding the connector out.
Step 5: Locate the T-MAP sensor jumper harness on the aFe POWER harness. It is identified with a white
label. Plug the female connector of the aFe POWER harness into the T-MAP sensor, then take the male
connector of the aFe POWER harness and connect to the female connector of the engine harness.
Make sure that the connections are fully engaged. Usually, connectors make a snapping
sound when fully engaged.
Figure C
INSTALL
T-MAP Sensor

Page 7
Refer to Figure D for Step 6
Step 6: Re-install the dust cover while making sure that the wire loom exits the cover through the slot on the
side of the cover. Re-install the plastic push clips and the hood latch.
INSTALL
Figure D

Page 8
Refer to Figure E for Step 7-8
Step 7: Locate the MAP sensor. It is located on top of the intake manifold. Disconnect the sensor by pulling
back on the locking tap and pressing down on the connector.
Step 8: Locate the MAP sensor jumper harness on the aFe POWER harness. It is labeled T-MAP. This is
the harness with four wires in each connector. Plug the female connector of the aFe POWER harness into
the MAP sensor, then the male connector of the aFe POWER harness into the female connector of the
engine harness.
Figure E
INSTALL

Page 9
Refer to Figure F for Step 9
Step 9: Check with the pictures to make sure the connectors are correctly connected.
Make sure that the connections are fully engaged. Usually, connectors make a snapping
sound when fully engaged.
INSTALL
Figure F

Page 10
Refer to Figure G for Steps 10-11
Step 10: Connect the red wire from the aFe POWER harness to the positive post on the battery terminal.
Step 11: Connect the black wire from the aFe POWER harness to the grounding post on the frame of the
vehicle.
INSTALL
Figure G

Page 11
Refer to Figure H for Steps 12-13
Step 12: Secure the Scorcher module on top of the driver side fender, next to the air filter housing. Secure
the module using the supplied Velcro.
Step 13: Connect the harness from the aFe POWER harness to the Scorcher Blue Module. Use the
provided cable ties to secure the harness away from any moving parts.
Note: The doors of the vehicle can now be opened to proceed with the installation of the LED switch.
INSTALL
Figure H
INSTALL
Figure H

Page 12
Refer to Figure I for Step 14-15 (Optional)
Step 14: Locate the grommet for the hood release cable inside of the cabin’s driver side footwell and slightly
pull it to the side in order to route the LED switch.
Step 15: Route the connector for the LED switch out to the engine bay using this hole.
Note: Installation of the LED switch is optional if using the Bluetooth app.
INSTALL
Figure I

Page 13
Refer to Figure J for Steps 16-18 (Optional)
Step 16: Carefully route the switch behind the steering wheel cover
Step 17: Mount the switch on an open, flat surface using the included double-sided tape.
Step 18: Connect the LED switch to the aFe POWER harness in the engine compartment.
The installation of the module itself is now complete. Keep reading the installation instruction to
learn how to use all of its features.
INSTALL
Figure J

Page 14
Refer to Figure K (Picture is for reference)
The blue LED light will start flashing once the module is connected to the car and the ECU is on. The blue
LED will become solid if the module gets connected through Bluetooth to a device
Figure K

Page 15
Refer to Figure L (LED Switch)
When turning on the vehicle, each LED will flash, and it will stop at its last setting. The LED on the switch
represents the different level of power.
•Green LED: Stock
•Yellow LED: Sport
•Orange LED: Sport+
•Red LED: Race
Use the grey button to select the desired setting. Power adjustments can be done at any time while the
unit is on. The LED switch can be used at the same time as the Bluetooth app.
Figure L

Page 16
Refer to Figure M* (app connection-iOS)
For iOS devices, download the app from the apps store. Make sure the Bluetooth is activated
on your device. Open the app and it will automatically connect through Bluetooth to the
SCORCHER BLUE module when both the vehicle and module are on. When connected, the
vehicle description will appear on top of the screen and the gauges will show current data.
The blue LED light on the module will become solid once connected to a Bluetooth device.
Simply tap on the green, yellow, orange and red button to switch between the modes.
*Screen shots shown here are for example only. Actual screen display will vary depending
on your vehicle.
Figure M

Page 17
Refer to Figure N* (app connection-Android)
For Android devices, download the app from the play store. For the initial connection, go to
the Bluetooth settings of your device, turn on Bluetooth and scan for available devices.
Select “aFe SCOR” and pair with device. The vehicle needs to be on and the module
connected. Once shown as paired device, open the app on your device and it will
automatically connect to the vehicle. The vehicle description will appear on top of the screen
and the gauges will show current data.
The blue LED light on the module will become solid once connected to a Bluetooth device.
Simply tap on the green, yellow, orange and red button to switch between the modes.
*Screen shots shown here are for example only. Actual screen display will vary depending
on your vehicle.
Figure N

Page 18
Refer to Figure O (Custom Tuning)
The aFe POWER SCORCHER BLUE app offers the capability to custom tune the different
modes. Go to the menu on the top right corner and select “Tune”. Select the mode you would
like to custom tune and adjust the sliders at low, medium, and high load. You can either write
the tune, reset, or exit without writing.
Disclaimer: Custom tuning should only be performed with the ignition in the “run”
position and engine off. Configuring the tunes outside the default values may cause
drivability issues and /or check engine lights to occur.
Figure O

Page 19
Refer to Figure P (Vehicle Performance Screen)
On the gauges screen, swipe to the left to get to the vehicle performance screen.
When the vehicle is not moving, select the test you are wanting to attempt (0-60mph, ¼ mile
or mile). The app will automatically detect the movement of the vehicle and the timer will
start. Once you reach the speed or distance, the timer will stop.
If you select a new mode, it will reset, and you can start again. If you need to stop the test at
any point, hit the cancel button and leave the screen.
Use the aFe POWER SCORCHER BLUE app responsibly. Always drive safely and obey traffic
laws. aFe POWER is not responsible for any accidents, injuries, or property damage that may
occur during its use.
Figure P

Page 20
Refer to Figure Q (Bypass Plug)
A bypass plug is included in the kit. The plug can be connected to the harness instead of the
module. Once the bypass plug is connected, the vehicle will run in factory settings. Make
sure the plug is fully engaged when connected to the harness. Thank you for choosing aFe
POWER!
The vehicle needs to be in sleep mode when the module gets disconnected and the
bypass plug connected. Wait for the blue LED on the module to stop flashing to make
sure the vehicle is in sleep mode.
Figure Q