AFi NORTHFIELD MURPHY BED WITH CHARGING STATION User manual

READY
Page 1 of 10
ASSEMBLY INSTRUCTIONS
QUEEN
B
E
C
D
A
G
F
I
H
JCB M6 X 25mm (1”) - 10 pcs
Barel Nut - 6 pcs
JCB M6 X 30mm (1 1/4”) - 6 pcs
JCB M6 X 60mm (2 3/8”) - 8 pcs
Wood dowel - 26 pcs
8 X 30mm
Spare - 1 pc
Spare - 1 pc
Spare - 1 pc
Spare - 1 pc
Spare - 2 pcs
Wood screw 1 1/2” - 2 pcs
Wood screw 1” - 17 pcs
Spare - 1 pc
Spare - 2 pcs
Triangle Bracket - 2 pcs
Allen wrench - 1 pc
Spare - 1 pc
PO :
NORTHFIELD MURPHY BED
WITH CHARGING STATION
Before assembling your murphy bed, please read through these
instructions carefully and familiarize yourself with the different parts.
ATTENTION! If you receive a damaged or defective item,
please contact afifurnishings at [email protected] or 1-800-955-3726
Adult assembly
Phillips screwdriver
Customer supplied
HARDWARE
NOTE: WE INCLUDE SPARE HARDWARE IN CASE DAMAGE OCCURS DURING ASSEMBLY.

02
01
03
04
05
06
07
08
09
10
11
12
13
14
15
1616
17
TOP PANEL
HARDWARE
LEFT SIDE PANEL
RIGHT SIDE PANEL
FRONT RAIL
SHELF
MIDDLE BACK RAIL
BOTTOM BACK RAIL
BACK PANEL
DOOR PANEL
DRAWER FACE
DRAWER SIDE
DRAWER BACK
DRAWER PANEL
DRAWER PANEL SUPPORT
DRAWER SIDE BLOCK
FOLDING MATTRESS
01
02
03
03
05
11
17
12
16
13
14
15
12 16
06
07
05
15
08
04
04
06
07 09
09
10
08
Page 2 of 10
1 BOX
1 BOX
1 BOX
1 BOX
C-5849X
C-5842X
C-5845X
A
A
A
A
A
A
A
A
A
A
A
A
Wooden dowel
A
PARTS LIST
STEP 1
Insert all wooden dowels (A) into the locator holes on (03)(04)(05)(06)(07)(08) and (15)
as shown below.
Adult assembly
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Adult assembly
Page 3 of 10
JCB M6 X 60mm
2 3/8”
JCB M6 X 25mm
1”
Barrel nut
Allen wrench
D
B
E
H
Adult assembly
STEP 2
Attach left side panels (03) to the shelf (06), front rail (05), middle back rail (07) and
bottom back rail (08) as shown below. Use JCB (B)(D) and barrel nut (E).
Tighten with Allen wrench (H)
Guide the back panel (09) in carefully so that it won’t jump out of its grooves. Be sure
it fits fully into its groove at the bottom (in the side panel) before fitting the other side
panel.
STEP 3
Phillips screwdriver
Customer supplied
03
06
07
09
08
05
E
E
E
B
B
D
D
D
B
B
B
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 4 of 10
STEP 4
STEP 5
Adult assembly
04
09
Attach right side panels (04) to cabinet assembly as shown below. Use
JCB (B)(D) and barrel nut (E).Tighten with Allen wrench (H)
Be sure it fits fully into its groove at the bottom
(in the side panel) before fitting the side panel.
BOTTOM VIEW
D
D
D
B
E
E
EB
B
B
E
E
D
D
Guide the back panel (09) in carefully so that it won’t jump out of its grooves. Be sure
it fits fully into its groove at the middle rail before fitting the top panel.
Adult assembly
JCB M6 X 60mm
2 3/8”
JCB M6 X 25mm
1”
Barrel nut
Allen wrench
D
B
E
H
Phillips screwdriver
Customer supplied
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 5 of 10
STEP 6
STEP 7
Attach top panel (02) to cabinet assembly as shown below. Use JCB (B).
Tighten with Allen wrench (H)
BOTTOM VIEW
Open top drawer folding leg until lock of metal support as shown below.
Top drawer folding leg
LOCK
B
B
B
B
B
B
JCB M6 X 25mm
1”
B
Allen wrench
H
Adult assembly
Adult assembly
02
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 6 of 10
STEP 8
STEP 9
Attach door panel to cabinet assembly as shown below. Use wood screw (F)
tighten with Phillips head screwdriver. (customer supplied).
Be sure to align with cabinet.
Adult assembly
Wood Screw 1”
F
Adult assembly
Lift the door and push the metal support. Push the door closed and latch both sides as
shown below.
Lock
Phillips screwdriver
Customer supplied
PUSH METAL SUPPORT
BOTH SIDE
PUSH
F
F
F
F
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 7 of 10
STEP 10
STEP 11
Attach triangle bracket (I) to the back of cabinet as shown below. Use wood screw (F)
tighten with Phillips head screwdriver. (customer supplied).
Triangle bracket
Wood Screw 1”
I
F
Adult assembly
F
FF
I
I
Lay the drawer face (11) on smooth, flat surface so the groove is facing upwards.
Fit the drawer side (12) to drawer face (11), Use JCB (C), align groove inside
panel with groove in drawer face. Tighten with Allen wrench (H).
11
12
12
C
C
CAdult assembly
JCB M6 X 30mm
1 1/4”
C
Allen wrench
H
Phillips screwdriver
Customer supplied
I
PILOT HOLES
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 8 of 10
STEP 12
STEP 13
Adult assembly
Guide the drawer panel (14) in carefully so that it won’t jump out of its grooves. Be sure it fits fully into
its groove at the bottom (in the drawer face) before fitting the drawer back. Attach drawer panel
support (15) to the drawer face as shown below.
Attach drawer back (13) and drawer side block (16) to bed drawer assembly as shown below. Use
JCB (C)(D). Tighten with Allen wrench (H). Use wood screw (G) tighten with Phillips head screwdriver.
(customer supplied)
14
13
15
C
C
G
G
D
D
16
16 Adult assembly
JCB M6 X 30mm
1 1/4”
JCB M6 X 60mm
2 3/8”
C
D
Wood screw 1 1/2”
G
Allen wrench
H
Phillips screwdriver
Customer supplied
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 9 of 10
STEP 14
STEP 15
Adult assembly
Adult assembly
Move the murphy bed where you want to place them in the room.
Push drawer assembly in as shown below. Be sure to align with cabinet.
Unlatch the door and open top drawer folding leg until lock of metal support, folding
down as shown.
Open
QUEEN
TOP DRAWER FOLDING LEG
NORTHFIELD MURPHY BED
WITH CHARGING STATION

Page 10 of 10
STEP 16
STEP 17
Adult assembly
Adult assembly
Open and pull footboard frame and open footboard leg as shown below.
FOOTBOARD FRAME
FOOTBOARD LEG
Install folding mattress (17) to the bed. Open top panel as shown below.
Congratulations!
Your Murphy bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use to ensure lasting Safety.
17
17
QUEEN
NORTHFIELD MURPHY BED
WITH CHARGING STATION