AFi Colorado Bed Frame User manual

ASSEMBLY INSTRUCTIONS
Before assembling your bed frame, please read through these
instructions carefully and familiarize yourself with the different parts.
BED FRAME
QUEEN
Page 1 of 2
3
2
1
A
A
A
B
B
B
ATTENTION! If you receive a damaged or defective item,
please contact afifurnishings at [email protected] or 1-800-955-3726
PARTS LIST HARDWARE
RIGHT LEG
LEFT LEG
FOOT / HEAD RAIL
SIDE RAIL
SLAT KIT
SLAT SUPPORT
SLAT SUPPORT LEG
2 PCS
2 PCS
2 PCS
2 PCS
2 SETS
2 PCS
2 PCS
1
2
3
4
5
6
7
Attach the right leg (1) and left leg (2) to the head rail (3) using JCB M6 X 110mm (A) and
barrel nut (B). Tighten with the Allen wrench M4 (I).
Repeat for foot rail assembly.
READY
ASSEMBLE
TO
Step 1
PO:
NOTE: WE INCLUDE SPARE HARDWARE IN CASE DAMAGE OCCURS DURING ASSEMBLY.
Barrel nut - 4 pcs
JCB M8 X 15mm ( 5/8") - 8 pcs
JCB M6 X 110mm (4 3/8”) - 4 pcs
Wood screw(1 1/4”) - 14 pcs
Spare - 1 pc Spare - 1 pc
Spare - 1 pc
A
D
E
F
H
I
J
K
G
L
B
C
Allen wrench M4 - 1pc
Split washer - 2pcs
Flat washer - 2pcs
Surface Mount Charger - 1set
Cap nut - 6pcs
Allen wrench M6 - 1pc
Spare - 1pc
Spare - 1pc
Spare - 1pc
Adult assemblyAdult assembly
JCB M6 X 110mm
Barrel nut
A
B
Screws 1/2" - 2 pcs
Spare - 1 pc
BACK VIEW
JCB M6 X 30mm(1 1/4") - 6pcs
JCB M8 X 40mm (1 5/8") - 2pcs
CODE ITEM
BD-COD-ISL G-23804X

E
F
QUEEN
Page 2 of 2
Attach the foot rail or head rail to side rails (4) using JCB M8 X 15mm (C). Tighten with
the Allen wrench M6 (H).
Attach slat support (6) to slat support leg (7) using JCB M8 X 40mm(G) split and flat washer
(J)(K). Tighten with Allen wrench M6 (H). Attach slat support (6) to the slat kit (5) as shown
below using JCB M6 X 30mm (E) and cap nut (F). Tighten with Allen wrench M4 (I).
Attach the USB charger (L) to the
location as shown below using 1/2"
screws and tighten with Phillips head
screw driver. (customer supplied)
Step 2
Step 3
Step 4 Step 5
Adult assemblyAdult assembly
JCB M8 X 15mm
C
4
4
C
G
E
E
EE
E
F
F
FF
DD
D
F
L
G
K
K
J
J
C
C
JCB M6 X 30mm
Cap nut
JCB M8 X 40mmSplit, Flat Washer
E
F
G
JK
Adult assemblyAdult assembly
6
6
7
7
Congratulations!
Your bed is now ready for use.
We recommend that you periodically recheck that all screws are tight to ensure lasting safety.
Screws 1/2"
6
6
5
5
Attach slat kit (5) to the bed frame as shown below
using wood screws 1 1/4" (D). Tighten with Phillips
head screw driver. (customer supplied)
5
Wood screw
DD
If using a Trundle Bed attach center
rail off center as shown.
Repeat for section 2.
SECTION 1
SECTION 1
SECTION 1
5