Dunelm Brisbane 2 Door 2 Drawer Robe User manual

DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and fittings in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out across the floor before you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, fixtures and fittings, as well as the tools you will need for assembly,
can be found on page 2 and 3 of this manual.
TOP TIP
Identify all of the fittings, make sure that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT - The first step you need to take is to ensure your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials way from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.

Panels - plan view
Left side
475 x 1978mm
Right side
475 x 1978mm
Top 795 x 497mm
Rail
739 x 78mm X 3
Panel -
exploded view
Shelf 739 x 458mm L/H Door
384 x 1530mm
R/H Door
384 x 1530mm
Back
752 x 1964mm
Parts & Fittings for the Brisbane 2 Door 2 Drawer Robe (30151822)
L/H bottom drawer
side 350 x 170mm
R/H bottom drawer
side 350 x 170mm
Bottom drawer
back
698.5 x 170mm
Bottom drawer front
771 x 244mm
L/H top drawer
side 350 x 110mm
R/H top drawer
side 350 x 110mm
Top drawer back
698.5 x 110mm
Drawer base
347 x 710mm X 2
Top drawer front
771 x 160mm
1 2
3
4
2
56 7
17
1
2
3
4
5
6
7
8
9
4
4
10
11
12
13
14
15 11
16
13
14
15
16
8
9
10
11
12
17

Cross slot screwdriver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
over tightening fixings
Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
Fittings
Front edge
Note: Insert metal
dowels as far as shown.
Soft close hinge
x 6
3
Euro screw s x 8
I
1
15mm
Metal cam x 10
A
Cam pin x 14
B
30mm
Wooden dowel x 14
C
Panel pins x 8
K
Handle screw x 8
S
13mm Screw x 16
H
Hinge plate
x 6
FG
Hanging rail
bracket x 2
733mm Hanging
rail x 1
O
B
B
B
1
BB
P
Wall bracket x 1 15mm Screw x 1
Q
50mm Screw x 4
J
Handle x 4
R
12mm
Metal cam x 4
D
Drawer wedge x 8
N
Soft close runner x 2 pair
T
Drawer peg x 8
L
Door stop x 2
M
E
B

10 mm
10 mm
4
2
3
C
C
C
B
2
C
F
1
This end to the
edge of the panel
B
B
B
B
B
G
H
C C
I
1
T
T
I
T
1
1

10 mm
X 3
10 mm
Ensurethe cam is pressed fully
into the hole and arrow pointing
towards the short edges
5
4
5
4
A
C
A
AA
C
4
4
C
C
F
2
This end to the
edge of the panel
G
H
I
2
T
T
I
T
2
2

Front edge
Ensurethe cam is pressed fully
into the hole and arrow pointing
towards the short edges
Rear edge
10 mm
Rear edge
Front edge
Cam lock in closed
position
Cam lock in open
position
A
A
6
6
7
2
AA
5
5
5
A
A
A
A
C
C
C
C
C
A
A
4
5
A
A
A
4
4
These panels must be
supported until the
next step

Front edge
Rear edge
Front edge
Rear edge
Front edge
7
8
9
Cam lock in closed
position
Cam lock in open
position
A
A
A
A
4
5
AA
A
4
4
2
1
3
M
M
M

Rear edge
Front edge
Ensure the FINISHED
surface is facing the
inside of the robe
Front edge
8
10
11
4
5
4
4
2
1
3
J
J
J
J
4
2
1
3
17
4
A to B = C to D

Two people required
to stand unit upright
Hinge to be at
90oto the edge
of the door
Hinge to be at 90oto
the edge of the door
9
12
13
14
4
2
1
3
17
K
K
17
K
17
H
7
E
H
E
H
E
H
E
H
90o
7
H
6
6
E
H
E
H
E
H
E
H
90o
E
E

To ensure the
door is the
right way up
this should
be 870mm
X 6
10
16
G
G
O
O
O
15
6
1
2
E
F
E
FPress to
dettach
Press to
attach
7
6
1
2
7
3
3