AFL Hyperscale 1024f L3 Mustang User manual

1024f L3 Mustang Splitter Backboard
Installation Guide
1024f L3
Mustang
Conguration SKU Code
1024HP 10014861

2© AFL Hyperscale. All rights reserved
Safety Precautions
Laser Precautions
Warning: The laser light used to transmit information over optical ber cables can cause severe eye
damage. Because this light is invisible, it will not cause the iris of the eye to contract involuntarily as when
viewing a bright visible light, and no pain is felt as the retina is burned.
Never look into the end of a ber or connector which may have a laser coupled to it. Should accidental
eye exposure to laser light be suspected, arrange for an eye examination immediately.
General Precautions
Personnel must be thoroughly familiarized with all applicable Occupational Health and Safety (OH&S)
regulations, local regulations, and your company safety practices and policies.
Warning: To reduce the chance of accidental injury:
Before work begins, all personnel must be thoroughly familiar with the operation of all equipment
and procedures to be used during the installation.
Before use, all equipment, especially safety gear, must be inspected and tested for proper operation.
Replace and repair as necessary.
1024f L3 Mustang Backboard
Before installing or adjusting this product, please read these instructions carefully.
Please keep this guide for future reference.

3
1024f L3 Mustang Backboard
© AFL Hyperscale. All rights reserved
Component Overview
1. Backboard
2. Modular Raceway
3. Loop Raceway
4. Splice tray
5. 2x 1:2 Splitter and Splitter Tray
6. 1:8 Splitter Tray
7. Cable / Tube Manifold
8. Single Duct Tie Point
9. Universal Duct Tie Point
10. Installation Guide / QR Code
10
01
09
08
07
06
06
02
03
05
04
04

4© AFL Hyperscale. All rights reserved
In the Box
Item
No Item Qty
01 Backboard 1
02 Modular Raceway 12
03 Loop Raceway 2
04 Splice Tray 4
05 2x Splitter and Splice Tray 8
06 1x8 Splitter Tray 32
07 Cable / Tube Manifold 2
08 Single Duct Tie Point 2
09 Universal Duct Tie Point 6
10 Installation Guide QR Code 1
(01) Backboard
(04) Splice Tray
Cable Ties
(07) Cable / Tube Manifold
Splice Protectors
(02) Modular Raceway
(05) 2x Splitter and Splice
Tray
Tube Cutter
(08) Single Duct Tie Point
Scissors Marker Pen
(03) Loop Raceway
(06) 1x8 Splitter Tray
(09) Universal Duct Tie
Point
(10) Installation Guide QR
Code
What You Will Need Related Products
FCP2 Fiber Cleaning Kit for SC/ST/FC/LC

5
1024f L3 Mustang Backboard
© AFL Hyperscale. All rights reserved
Backboard Installation
Slot studs into back panel – no tools required.
1
Backboard must be central, top, location as shown.
Rear Section View

6© AFL Hyperscale. All rights reserved
Cable Routing
Overall Routing
2
1:8 Splitter Inputs
(routed to 2 x 1:2 tray)
1:2 Splitter Inputs
(routed to splice tray) L4 distribution ber
Network ber
from L2.5
Tray 24
Tray 1

7
1024f L3 Mustang Backboard
© AFL Hyperscale. All rights reserved
Tray Map
L3 Mustang 1024HP
Tray map for splicing – Match the splitter letter to input tail letter
3
LHS Stack
Tray
Position Tray Type Input Tails Splitters Output Tails
24 1x8 Splitter Tray N
23 1x8 Splitter Tray M
22 1x8 Splitter Tray L
21 1x8 Splitter Tray K
20 1x8 Splitter Tray J
19 1x8 Splitter Tray I
18 1x8 Splitter Tray H
17 1x8 Splitter Tray G
16 1x8 Splitter Tray F
15 1x8 Splitter Tray E
14 1x8 Splitter Tray D
13 1x8 Splitter Tray C
12 1x8 Splitter Tray B
11 1x8 Splitter Tray A Splitter
Letter
10 2x1:2 Splitter
Tray
Splitter 2 Tail 2 FF
Tail 1 EE
Splitter 1 Tail 2 DD
Tail 1 CC
92x1:2 Splitter
Tray
Splitter 2 Tail 2 BB
Tail 1 AA
Splitter 1 Tail 2 Z
Tail 1 Y
82x1:2 Splitter
Tray
Splitter 2 Tail 2 X
Tail 1 W
Splitter 1 Tail 2 V
Tail 1 U
72x1:2 Splitter
Tray
Splitter 2 Tail 2 T
Tail 1 S
Splitter 1 Tail 2 R
Tail 1 Q
62x1:2 Splitter
Tray
Splitter 2 Tail 2 P
Tail 1 O
Splitter 1 Tail 2 N
Tail 1 M
52x1:2 Splitter
Tray
Splitter 2 Tail 2 L
Tail 1 K
Splitter 1 Tail 2 J
Tail 1 I
42x1:2 Splitter
Tray
Splitter 2 Tail 2 H
Tail 1 G
Splitter 1 Tail 2 F
Tail 1 E
32x1:2 Splitter
Tray
Splitter 2 Tail 2 D
Tail 1 C
Splitter 1 Tail 2 B
Tail 1 A
2 Splice Tray - -
1 Splice Tray - -
RHS Stack
Tray
Position Tray Type Input Tails Splitters Output Tails
24 - - - -
23 - - - -
22 - - - -
21 - - - -
20 1x8 Splitter Tray FF
19 1x8 Splitter Tray EE
18 1x8 Splitter Tray DD
17 1x8 Splitter Tray CC
16 1x8 Splitter Tray BB
15 1x8 Splitter Tray AA
14 1x8 Splitter Tray Z
13 1x8 Splitter Tray Y
12 1x8 Splitter Tray X
11 1x8 Splitter Tray W
10 1x8 Splitter Tray V
9 1x8 Splitter Tray U
8 1x8 Splitter Tray T
7 1x8 Splitter Tray S
6 1x8 Splitter Tray R
5 1x8 Splitter Tray Q
4 1x8 Splitter Tray P
3 1x8 Splitter Tray O
2 Splice Tray
1 Splice Tray

8© AFL Hyperscale. All rights reserved
1:2 Routing
Route 1:2 splitter inputs down to network splice tray. 1:2 splitter outputs splice to 1:8.
4
1:8 Splitter Inputs
(routed to 1:8 tray)
1:2 Splitter Inputs
(routed to splice tray)
1:2 Splitter Outputs
1x2 G.657A2 splitter
Splice protectors
Splitter 2
Splitter 1

9
1024f L3 Mustang Backboard
© AFL Hyperscale. All rights reserved
Splice 1:2 Inputs to network ber.
5
1:2 Input Splicing
1:2 Splitter Inputs
(routed to splice tray)
Network ber
from L2.5
Splice protectors

10 © AFL Hyperscale. All rights reserved
Splice 1:8 Outputs to L4 distribution ber
6
1:2 Output to 1:8 Input & 1:8 Output Splicing
1:8 Splitter
Inputs
L4 distribution
ber
1:8 Splitter
outputs
(250µm)
Splice
protectors
1:8 Splitter
Outputs (250µm)
1x8 G.657A2
splitter

11
1024f L3 Mustang Backboard
© AFL Hyperscale. All rights reserved
Splitter Specication
Type 1xN 1:2 1:8
Operating Wavelength Range (nm) 1260~1650nm 1260~1650nm
Insertion Loss (dB) Max 4.0 10.5
PDL (dB) Max 0.2
Uniformity (dB) Max 0.4 0.8
PLC Return Loss (dB) Min 55
Directivity (dB) Min 55
Operating Temperature (°C)
-40~+85
Storage Temperature (°C)
Housing Dimension (mm) LxWxH 60x7x4 60x7x4
Fiber Type G.657A2 G.657A2

Thank you for choosing AFL Hyperscale
AFLHS1024L3M080622
www.aflhyperscale.com
AFL Hyperscale reserves the right to make changes in this Installation Guide at any time without notice
Installation GuideInstallation Guide