AGCO SP002V9810010 User manual

Operator's Manual
Wheel Weights Handling Tool
SP002V9810010
Wheel weight handling tool
Marktoberdorf
AGCO GmbH - Johann-Georg-Fendt-Str. 4 - D-87616 Marktoberdorf
© AGCO 2023
Original Operator's Manual
August 2023
SP002P001B01A
EME
English

Wheel Weights Handling Tool
SP002P001B01A
How to use this manual
General
You must read this manual before you operate or do work on the machine.
If more assistance is necessary you should speak to your AGCO dealer.
This manual is only applicable to the models specified on the front cover.
Contents
For quick reference, there is an index at the back of the manual. The index lists the contents and the location
in the manual. Each chapter starts with a table of contents which includes the different sections in that
chapter.
Fastener torques
Always replace fasteners with fasteners of the same specification. Tighten all fasteners to the correct torque
values.
You can find the list of torque values in the service manual or the assembly instructions of the machine. If the
torque value is different, it is specified in the procedure.
Special tools
If it is necessary to use a special tool in a procedure, the tool identification is specified in the procedure.
Illustrations
The illustrations do not always show the same machine specification or machine configuration. The
procedure is the same unless the instruction tells you differently.
The illustrations in this manual use a color system to help you follow the instruction correctly.
Color Description Functions
Target/focus item
The primary component in the step is this color.
Primary component, decal location,
component location
Connectors, fasteners
All components that attach the primary component
to a different component are this color.
Fasteners, electrical connectors
Primary alternative
If there are 2 primary components in the
illustration, 1 of the 2 components is this color.
Secondary component
Secondary alternative
If there are 3 primary components in the
illustration, 1 of the 3 components is this color.
Tertiary component
Special tool
Where the special tools or equipment are in an
illustration, they are this color.
Pressure gauges, specified tools

Wheel Weights Handling Tool
SP002P001B01A
Color Description Functions
Parts that you move
A component that you must move, and that is not
necessary to remove from the machine.
Electrical wires, hydraulic hoses
Sections
Where a cross-section of a component is
necessary, this color shows the component that
you see through.
Engines, drivetrain
Channels
To show the flow of liquid in a channel.
Engines, drivetrain
Temperature
Where the temperature of liquid changes.
•Blue - Cold
•Red - Hot
Coolant flow, water flow
Pressure
Where the pressure or state of gas changes.
•Yellow - Low
•Orange - High
SCR system, hydraulic systems

Wheel Weights Handling Tool
SP002P001B01A
Table of Contents
Wheel Weights Handling Tool
How to use this manual ........................................................................................................ 3
1 Safety ........................................................................................................................................ 7
1.1 Safety Icons ............................................................................................................... 9
1.2 Safety instructions ................................................................................................. 10
1.3 Waste disposal ........................................................................................................ 11
2 Maintenance and storage .................................................................................................. 13
2.1 Maintenance............................................................................................................. 15
2.2 Storage ...................................................................................................................... 16
3 Introduction........................................................................................................................... 17
3.1 Bill of Materials........................................................................................................ 19
3.2 Type Plate and Inspection sticker ...................................................................... 20
3.3 Intended use ............................................................................................................ 21
4 Operation ............................................................................................................................... 23
4.1 Preparation............................................................................................................... 25
4.1.1 Install the wheel weight tool safely on to the forks .............................................25
4.2 Use of the lift tool.................................................................................................... 26
4.2.1 Remove the wheel weight from the machine.....................................................26
4.2.2 Install the Wheel Weight to the machine ...........................................................28
4.3 Operation complete ............................................................................................... 31
4.3.1 Remove the wheel weight tool safely from the forks ..........................................31
Index........................................................................................................................................ 33

Wheel Weights Handling Tool
SP002P001B01A
Table of contents

Table of contents
Wheel Weights Handling Tool
SP002P001B01A
7
1 Safety
1.1 Safety Icons......................................................................................................................... 9
1.2 Safety instructions .......................................................................................................... 10
1.3 Waste disposal ................................................................................................................. 11

Table of contents
8 Wheel Weights Handling Tool
SP002P001B01A

1 Safety
Wheel Weights Handling Tool
SP002P001B01A
9
1.1 Safety Icons
NOTE: The use of the signal words DANGER, WARNING and CAUTION with the safety messages. The
signal word for each message will use the structure that follows:
DANGER: Danger
Shows data on a possible hazard that if you do not prevent death or injury will occur.
WARNING: Warning
Shows data on a possible hazard that if you do not prevent death or injury will occur,
these will include hazards that occur when guards are not in position.
CAUTION: Caution
Shows data on a possible hazard that if you do not prevent can cause small or moderate
injury or component or property damage.
NOTE: This shows more data that can help.

1 Safety
10 Wheel Weights Handling Tool
SP002P001B01A
1.2 Safety instructions
Make sure that you have the Operator's Manual for the machine you are to install the kit to.
Read and obey all safety instructions in the Operator's Manual of the machine before you
continue with these instructions
If you do not obey the instructions, there is a risk of injury.
In most conditions you can prevent injuries if you see dangerous situations before an injury occurs.
The person that installs this kit must be an approved technician and have the necessary tools.
Do not change the equipment. An adjustment not specified by the manufacturer can change the function of
the machine and cause damage or personal injury.
Only use AGCO approved replacement parts.
WARNING:
To prevent injury and machine damage, you must:
•Use the Personal Protective Equipment (PPE) applicable to the task.
– Eye protection
– Hand protection
– Foot protection
– Ear protection.
•Park the machine on a solid level surface.
•Disengage the PTO, if installed.
•Set the transmission to park and apply the parking brake.
•Set the control console to OFF.
•Stop the engine and remove the key.
•Look and listen! Wait for the parts that move to stop before you start the work.
•Put wheel chocks in front of and behind the wheels before you do work on or below the machine.
•Remove or release all sources of energy, for example:
– Disconnect the battery.
– Release of pressure from a system.
– Lock the parts that move.
•Clean the oil, dirt, and crop material from the area on the machine where you do the work.
Good safety procedures prevent accidents to you and each person near you.

1 Safety
Wheel Weights Handling Tool
SP002P001B01A
11
1.3 Waste disposal
Incorrect disposal of waste can cause pollution to the environment. Some examples of dangerous waste
materials include oil, fuel, coolant, battery chemicals and air-conditioning refrigerant.
•Only use an approved container to collect the waste material. Always seal the container after you drain
the fluids.
•Do not drain or spill waste on the ground, down a water drainage system or into water sources.
•Air-conditioning refrigerant released into the air can cause damage to the environment. The local
regulations recommend that only an approved technician removes and recycles the air-conditioning
refrigerant.
•Obey pollution laws.
•Speak with the local authorities on the correct procedure to discard of the waste.
Recycling centres or approved dealers have the correct equipment for the disposal of used oil.
Fig. 1
Do not discard material with this symbol in the
general waste.
Fig. 2
Recycle used materials with this symbol.

1 Safety
12 Wheel Weights Handling Tool
SP002P001B01A

Table of contents
Wheel Weights Handling Tool
SP002P001B01A
13
2 Maintenance and storage
2.1 Maintenance ...................................................................................................................... 15
2.2 Storage ............................................................................................................................... 16

Table of contents
14 Wheel Weights Handling Tool
SP002P001B01A

2 Maintenance and storage
Wheel Weights Handling Tool
SP002P001B01A
15
2.1 Maintenance
•Clean the tool before and after use. A dirty tool can be slippery which can be dangerous.
•Do a check of the tool before you use the tool. Do not use the tool if it is unserviceable. Make sure all of
the components are serviceable.
•The components of the tool must be lubricated regularly with grease. Regular maintenance keeps the
tool serviceable for a longer period of time.

2 Maintenance and storage
16 Wheel Weights Handling Tool
SP002P001B01A
2.2 Storage
IMPORTANT: Do not store the tool outside.
Make sure that tool is stored correctly. The tool must be stored in a dry environment away from regular work
areas. If it is possible, storing the tool in a dust free environment helps the serviceability and maintenance of
the tool.

Table of contents
Wheel Weights Handling Tool
SP002P001B01A
17
3 Introduction
3.1 Bill of Materials ................................................................................................................. 19
3.2 Type Plate and Inspection sticker................................................................................ 20
3.3 Intended use...................................................................................................................... 21

Table of contents
18 Wheel Weights Handling Tool
SP002P001B01A

3 Introduction
Wheel Weights Handling Tool
SP002P001B01A
19
3.1 Bill of Materials
Fig. 1
Description Quantity
1 Chassis of the tool 1
2 Safety hook and chain 1
3 Roller 4
4 Type plate 1

3 Introduction
20 Wheel Weights Handling Tool
SP002P001B01A
3.2 Type Plate and Inspection sticker
Type plate
Fig. 2
(1) Part number
(2) Title of the tool
(3) QR code (Link to the product web page)
(4) Maximum load rating (1250 kg)
(5) Serial number
Inspection sticker
Fig. 3
WARNING:
Never use a tool that is untested or has
not had its routine inspection.
•The tool needs to be inspected regularly.
•The inspection must align with the local
regulations.
•A new sticker must be applied after the
inspection.