AGD 924R SA-146 User manual

ISO 14001
Registered
Environmental
Management015
ISO 9001
Registered
Quality
Management015
SA-146 LED Wait Indicator
SA-149 Higher Current Wait Indicator
PRODUCT MANUAL
©AGD Systems Limited 2017 Doc. Ref. 924R PM ISS4

The bracket (BR-230) and pcb (CB-277/CB-318) are
designed to cover a range of bulb wait housing options.
For each of these the orientation of bracket and pcb
are very specific as detailed in the diagrams above.
Please note particularly that the bracket has
two orientations marked A&B.
1. Identify existing bulb unit as Option 1-4
2. Remove existing lamp configuration and wiring
as appropriate
3. Remove the pcb CB-277/CB-318 from the bracket,
keeping the screws to one side ensuring no
contact is made directly with the LED’s
OPTION 1
OPTION 2
Use existing
M3 hole
Note logo
orientation
Note orientation
Use
existing
M3 hole
Note logo
orientation
Note
orientation
INSTALLATION

4. Using the appropriate screw fixings secure
the bracket BR-230 to the rear housing in the
position shown
5. Refit the pcb to the bracket noting the orientation
of the AGD logo on the pcb on the relevant diagram
6. Connect wiring per the table below
OPTION 3
OPTION 4
Use
existing
M3 hole
Drill and
Tap M5
Note logo
orientation
Note logo
orientation
Note
orientation
Note
orientation
The LED wait
retro fit kit
(SA-146)
is designed
to replace
existing bulb
version Waits
with a 48Vac
low power
LED pcb and
comprises:
Preview Item Part Number QTY
1BR-230 1
2M3x8 Pan
Head Self Tap 4
3CB-277 1
4M5x8
Pan Head 1
5M5 Shk Proof 1
6M3 Shk Proof 1
7M3x6
Pan Head 1
INSTALLATION

INTRODUCTION
SAFETY PRECAUTIONS
Important note: Do not touch the surface of the
LED’s. For maintenance purposes users should
take particular care and avoid exposure to the
high intensity LED light output. Although the
LED’s are not laser devices they have a high brightness and thus to ensure maintenance engineer “eye-safety”,
DO NOT LOOK DIRECTLY INTO THE LEDS when opening the unit or powering the pcb.
The kit is supplied with the pcb reversed on the bracket to protect the LED’s whilst in transit.
POWER & WIRING
CB-277 (fitted to AGD924-68X-XXX) CB-318 (fitted to AGD924-69X-XXX)
DISCLAIMER
While we (AGD Systems) endeavour to keep the information in this manual correct at the time of print, we make no
representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability
or availability with respect to the information, products, services, or related graphics contained herein for any purpose.
Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss
or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever
arising from loss of data or profits arising out of, or in connection with, the use of this manual.
WARRANTY
All CB-277 and CB-318 retrofit pcb’s are covered by a one year return to factory warranty. Products falling
outside this period may be returned to AGD Systems for evaluation and chargeable repair.
The CB-318 consumes a nominally higher current than the CB-277. This is for controllers that require a
nominally higher current for monitoring purposes. The CB-318 takes 71% and 25% more power in dim and
bright modes.
AGD Systems Limited
White Lion House T: [phone]
Gloucester Road, F: [phone]
Staverton, Cheltenham E: [e-mail]
Gloucestershire, GL51 0TF, UK W: agd-systems.com
ISO 9001
Registered
Quality
Management015
ISO 9001
Registered
Quality
Management015
©AGD Systems Limited 2017 Doc. Ref. 924R PM ISS4
Wire Colour Function
Red 48V ac
Red 48V ac
Wire Colour Function
Red 48V ac
Red 48V ac
Nominal power
consumption in
bright mode
10.2W - 11.2W 48Vac.
Nominal power
consumption in
bright mode
12.48W - 48Vac.