Agilent Technologies E5810 Installation and operation manual

Agilent Technologies
Agilent E5810 LAN/GPIB Gateway
Agilent E5818 LXI Class-B Trigger Box
Rack Mount Installation Note
One rack mount kit contains the hardware to mount a single E5810/E5818 or two E5810s/E5818s, side-by-side.
Advanced Test Equipment Rentals
www.atecorp.com 800-404-ATEC (2832)
®
E
s
t
a
b
l
i
s
h
e
d
1
9
8
1

Rack Mounting Single E5810/E5818 (see other side to rack mount two
E5810s/E5818s)
1. Remove both rubber bumpers from the E5810/E5818.
2. Using Pozidriv screwdriver, attach Rack Ear-Half Rack (B) to the E5810/E5818 with three M4x10 Panhead
Screws (C).
3. Using Pozidriv screwdriver, attach Rack Ear-Full Rack (A) to the E5810/E5818 with three M4x10 Panhead
Screws (C).
This rack mount is suitable for both E5810 and E5818 units.
E5810 E5818
Parts needed to install a single E5810/E5818 in a rack:
AE5810-00021 Rack Ear - Full Pack 1D0570-1581 Screw, Machine 4
BE5810-00022 Rack Ear - Half Rack 1E0590-0804 Nut, Machine 4
C0515-1114 Screw, Panhead, M4x10 6
Rubber Bumpers
Rubber Bumpers
B
C
C
A
2

4. Do the connections based on the diagrams below:
5. Using Philips screwdriver, attach Rack Ears to rack with four Machine Screws (D) and four Machine Nuts (E).
A. Rear View of the E5810 B. Rear View of the E5818
Connect GPIB and RS-232 cables. Plug AC Power cord
into AC Power port on the E5810.
Connect BNC cables. Plug AC Power Cord into AC Power
port and the E5818.
GPIB RS-232 Power
LAN Ln
Tx
GPIB
R
t
RS232
POWER
!
1PPS 100-240VAC
50-60Hz25VA
RS232
LAN
Act
Ln
ICES/N MB-0 01
ISM 1-A
N10149
CUS
206349
EXT 1
IN
TTL1
OUT
EXT2
IN
TTL 2
OUT
D
Rack Cabinet
Part of
four Machine Nuts (E).
D
E
Right Vertical Rail
E
Left Vertical Rail
(Front)
(Front)
GPIB RS-232 Power TTL2 EXT2 TTL1 EXT1 1PPS Power
OUT IN OUT IN
3

Rack Mounting Two E5810s/E5818s (see other side to rack mount single
E5810/E5818)
1. Remove both rubber bumpers from the E5810/E5818.
2. Using Pozidriv screwdriver, install a Lock Link (A) on each E5810/E5818 with a Flathead Screw (G). Then, slide
the two E5810s/E5818s together so the Lock Links interconnect. See detail “A”.
3. Using Pozidriv screwdriver, remove the screw at the rear of each E5810/E5818. Then, connect the Rear Bracket
(B) to each E5810/E5818, using the screws you just removed.
4. Using Pozidriv screwdriver, attach Rack Ear-Full Rack (C) to each E5810/E5818 with six M4x10 Panhead Screws
(D).
Parts needed to install two E5810s/E5818s, side-by-side, in a rack:
A0050-2166 Lock Link 2E0515-1367 Screw, Flathead,
M4x8
2
BE5810-00023 Bracket, Rear 1
CE5810-00021 Rack Ear - Full Rack 2F0570-1581 Screw, Machine 4
D0515-1114 Screw, Panhead, M4x10 6G0590-0804 Nut, Machine 4
Rubber Bumpers
Rubber Bumpers
Detail "A"
G
AA
D
C
D
C
B
Rear Bracket (B) to each E5810,using the screws you just removed.
E
4

5. Do the connections based on the diagrams below:
6. Using Philips screwdriver, attach Rack Ears to rack with four Machine Screws (F) and four Machine Nuts (G).
A. Rear View of the E5810 B. Rear View of the E5818
Connect GPIB and RS-232 cables. Plug AC Power cord
into AC Power port on the E5810.
Connect BNC cables. Plug AC Power Cord into AC Power
port and the E5818.
GPIB PowerRS-232
LAN Ln
Tx
GPIB
RS232
POWER
!
1PPS 100-240VAC
50-60Hz25VA
RS232
LAN
Act
Ln
ICES/NMB-001
ISM 1-A
N10149
CUS
206349
EXT 1
IN
TTL1
OUT
EXT 2
IN
TTL 2
OUT
E
Part of
Rack Cabinet
E
RightVerticalRail
F
(Front)
F
Left Vertical Rail
(Front)
G
G
F
F
GPIB RS-232 Power
TTL2 EXT2 TTL1 EXT1 1PPS Power
OUT IN OUT IN
5

© Agilent Technologies, Inc. 2004 −2008
Printed in Malaysia
Third Edition, January 31, 2008
E5810-99100
Agilent Technologies