Agilent technologies E4400-60230 g Quick start guide

Firmware Upgrade Guide

Part Number E4400-90549

Printed in USA July 2012

Supersedes May 2005

Agilent Technologies Firmware Upgrade Kits

E4400-60230 and E4400-60597

for ESG/PSG Signal Generators

Notice

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable

for errors contained herein or for incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Microsoft®, Windows®, Windows NT®are U.S. registered trademarks of Microsoft Corporation.

NI-488.2 is a trademark of National Instruments Corporation.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal

Generators

Introduction

The instructions in this firmware upgrade guide enable you to install the PSG/ESG Upgrade Assistant 5.12 on your

computer from either the Agilent Technologies website or a CD-ROM and upgrade firmware on ESG-B signal generators

with <B.03.20.

NOTE For Agilent E44xxB ESG Signal Generators Models Only

When upgrading Agilent E44xxB ESG signal generators from firmware versions <B.03.20, see, “ESG-B

Firmware Installation For Versions <B.03.20” on page 14.

To upgrade firmware on PSG/ESG signal generators, perform the following procedures:

1. Check signal generator functionality on page 5.

2. Confirm required equipment on page 6.

3. Connect an RS-232, GPIB, or LAN interface to a PC on page 8.

4. Install PSG/ESG Upgrade Assistant 5.12 and firmware files on page 11.

5. Use the PSG/ESG Upgrade Assistant 5.12 with firmware files on page 12.

6. Check signal generator functionality on page 5.

Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . All

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . All

Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All except Option H98

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center

(X) Personnel Qualified by Agilent Technologies

(X) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . 75 minutes (RS-232), 30 Minutes (GPIB), 3 minutes

(LAN)

Estimated Verification Time: . . . . . . . . . . . . . . . 1 minute

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Overview of Upgrade Assistant 5.12

PSG/ESG Upgrade Assistant 5.12 is used for upgrading firmware on PSG/ESG signal generators:

• it is a Windows-based program

• it replaces PSG/ESG Upgrade Assistant 5.00 through 5.11

as well as ESG Upgrade Assistant 2.12, 2.22, and 3.3.

• it allows new and previous versions of firmware installations to be performed using either:

— RS-232 or GPIB on Agilent E44xxB ESG Signal Generators

— GPIB or LAN on Agilent E44x8C ESG Signal Generators

— GPIB or LAN on Agilent E824xA/5xA PSG Signal Generators

— GPIB or LAN on Agilent E82x7C/D PSG Signal Generators

• it has an associated HTML page that describes the following information for each firmware upgrade version:

— information about new features and enhancements

— a list of improvements and defects that have been fixed

— hardware compatibility

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

Use the following procedure to confirm that the signal generator powers up and that the internal check identifies no errors.

The internal check evaluates the operation of the signal generator and returns an error message if it detects a problem.

NOTE The signal generator must warm up for at least five minutes and all errors must be cleared from the error

queue before a firmware upgrade can be successfully completed.

If errors exist in the error queue and a firmware upgrade is attempted, the firmware upgrade will be

unsuccessful; new DSP code cannot be upgraded until the error queue has been cleared.

When signal generators with Option 1E5 are first connected to ac line power, the error message

ERROR 514, Reference Oven Cold occurs, causing both the OVEN COLD annunciator and the ERR

annunciator to turn on.

After approximately five minutes, the OVEN COLD annunciator automatically clears, but the ERR

annunciator remains on until all errors are cleared from the error queue.

To check signal generator functionality

1. Turn on power to the signal generator and let it warm up for at least five minutes.

2. Cycle power on the signal generator. The green LED should light and the signal generator should perform a

functionality check.

3. When the display lights, check to see if the ERR annunciator is on.

• If the ERR annunciator is on, review the error messages in the error queue by pressing

Utility > Error Info >View Next Error Message. The first error message in the error queue appears in the display

text area. (Refer to the signal generator error messages list on the documentation CD for information about each

error message.)

After resolving all problems causing errors, press ClearErrorQueue(s).

• If the ERR annunciator is off, the signal generator functionality check has passed.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Confirm Required Equipment

This section lists the minimum computer hardware, operating system, and software that are required to perform firmware

upgrades on PSG/ESG signal generators.

Computer IBM compatible PC with a 486 MHz processor or greater

RAM Required 64 MB or more

Hard Disk Space Required 20 MB or more

This could increase significantly if a large library of firmware

upgrade files are expected to be maintained on the PC. A single

firmware release consists of approximately 5 to 8 MB of data.

CD-ROM Drive or Modem Use of a CD-ROM drive is only required when the computer being

used does not have Internet access.

Use of a 56 kbps modem is only required for systems downloading

firmware updated from the Internet.

RS-232, GPIB, or LAN Connection •If you plan to perform a firmware upgrade using RS-232, refer

to the “RS-232 Installation Kit (Only for use with

Agilent E44xxB ESG Signal Generators)” on page 6.

While making the RS-232 connection, a 5-mm nut driver, part

number 8710-1219, is used to remove the screws from the

serial interface (f) to (f) adapter.

•If you plan to perform a firmware upgrade using GPIB, refer

to “GPIB Interface Requirements” on page 6.

•If you plan to perform a firmware upgrade using LAN, a

10Base-T LAN interface is required. Contact your network

administrator if problems are encountered.

Operating System Windows XP, 2000, or Windows NT 4.0 (with Service Pack 5 or

above)

Internet Browser Use of an Internet Browser is only required for downloading

firmware files from the Internet or for viewing firmware release

information on your local PC or over the Internet.

Microsoft Internet Explorer 4.0 and above, or Netscape Navigator

4.0 and above

Either browser must be Java enabled with Java 1.02 or above.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

RS-232 Installation Kit

(Only for use with Agilent E44xxB ESG Signal Generators)

GPIB Interface Requirements

Quantity Description Part Number

1 Firmware Upgrade Guide E4400-90549

1 PSG/ESG Firmware Upgrade CD-ROM E4400-10501

1 RS-232 Cable Kit:

•Serial RS-232 Cable (8120-6188)

•RS-232 Null Modem (5181-6639)

•Adapter, (f) to (f) (1252-7825)

E4400-60049

Interface Cards Manufacturer Driver Software Version Windows Version

Agilent 82341C for

ISA bus computers Agilent Technologies I/O Libraries SICL &

VISA J.01.01.00 XP/2000/NT 4.0

Agilent 82350A for

PCI bus computers

PCI-GPIB National Instruments NI-488.2M 1.60 XP/2000/NT 4.0

PCI-GPIB+ XP/2000/NT 4.0

PCMCIA-GPIB XP/2000/NT 4.0

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Connect an RS-232, GPIB, or LAN Interface to a PC

To connect the signal generator to a PC using an RS-232 interface

(Only for use with Agilent E44xxB ESG Signal Generators)

1. Connect Agilent E44xxB ESG signal generators to the PC as shown in the following diagram. Use a 5-mm nut driver to

remove both standoffs (screws) from the female-female adapter.

RS-232 communications are connected to one of the COM ports on the PC using an RS-232 serial cable with a

null-modem connected between the COM port and the signal generator’s RS-232 connector. Refer to the “RS-232

Installation Kit (Only for use with Agilent E44xxB ESG Signal Generators)” on page 7 for more information.

NOTE Ensure that the selected COM port is not used by any other device while

PSG/ESG Upgrade Assistant 5.12 is being used.

2. Set the RS-232 parameters as follows on the Agilent E44xxB ESG signal generators:

a. Press the following keys:

Preset (factory defined)

Utility > GPIB/RS-232

RS-232 Baud Rate > 19200

RS-232 Echo > Off

RS-232 Pace >

Transmit Pace > None

Receiver Pace > Xon

RTS/CTS > RTS On

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

To connect the signal generator to a PC using a GPIB interface card

1. Connect the signal generator to the PC as shown in the following diagram.

GPIB communications require a GPIB interface card installed in the PC and a GPIB cable connected between the

interface card and the signal generator’s GPIB connector.

Two common GPIB interface cards are the National Instruments PCI–GPIB and the Agilent GPIB interface cards.

(Refer to “GPIB Interface Requirements” on page 7 and refer to the documentation that came with the GPIB interface

card for information related to installing and configuring the GPIB interface card in your computer.)

2. Set GPIB parameters as follows on PSG/ESG signal generators:

a. Press the following keys for the model being set:

b. Use the numeric keypad, the arrow keys, or rotate the front panel knob to set the desired address and press Enter.

The signal generator’s GPIB address is set to 19 at the factory. The acceptable range of addresses is 0 through 30.

Once initialized, the state of the GPIB address is not affected by a signal generator preset or by a power cycle. Other

instruments on the GPIB cannot use the same address as the signal generator.

Agilent E44xxB ESG Signal

Generators Agilent E44x8C ESG Signal

Generators Agilent E82x7C/D PSG Signal

Generators

and Agilent E824xA/5xA PSG

Signal Generators

Utility > GPIB/RS-232 >

GPIB Address > 19 Utility > GPIB/RS-232/LAN >

GPIB Address > 19

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

To connect the signal generator to a PC using a LAN interface card

1. Connect the signal generator to the PC as shown in the following diagram.

LAN communications require a LAN interface card installed in the PC and a LAN cable connected between the

interface card and the signal generator’s LAN connector. LAN communications require a 10Base-T LAN interface.

Contact your network administrator if problems are encountered.

2. Set LAN parameters as follows on PSG/ESG signal generators:

a. Press the following keys for the model being set:

b. Use the numeric keypad to set the desired address and press Enter.

The signal generator LAN address is not set at the factory. Contact your network administration to obtain an

appropriate IP address.

c. Set the Sockets SCPI parameters by pressing Utility > GPIB/RS-232/LAN > LAN Services Setup > Sockets SCPI:

On to use the E44x8C firmware installation tool.

Agilent E44xxB ESG Signal

Generators Agilent E44x8C ESG Signal

Generators Agilent E82x7C/D PSG Signal

Generators

and Agilent E824xA/5xA PSG

Signal Generators

LAN is not available on E44xxB

ESG Signal Generators. Utility > GPIB/RS-232/LAN >

LAN Setup > Hostname >

(enter the instrument name) or

(IP address)

Utility > GPIB/RS-232/LAN >

LAN Setup > Hostname >

(enter the instrument name) or

(IP address)

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

Install PSG/ESG Upgrade Assistant 5.12 and Firmware Files

PSG/ESG Upgrade Assistant 5.12 is used along with firmware files to upgrade the firmware on PSG/ESG signal generators.

They are both available for download from the Agilent Technologies website or from a CD-ROM.

To install the PSG/ESG Upgrade Assistant 5.12

and firmware files from the Agilent Technologies website

1. Access the Agilent Technologies website by typing: http://www.agilent.com/find/upgradeassistant

or type “upgradeassistant” in the Quick Search box from the Agilent Technologies website.

2. Download and install the PSG/ESG Upgrade Assistant 5.12 installation program onto your computer.

The installation program places the PSG/ESG Upgrade Assistant 5.12 in a default installation folder

(C:\Program Files\Agilent\PSG-ESG Upgrade Assistant). The default installation folder can be changed using the

Browse button.

3. Download and install a version of PSG or ESG firmware files onto your computer.

The installation program places the selected firmware files in a default installation folder

(C:\Program Files\Agilent\PSG-ESG Upgrade Assistant). The default installation folder can be changed using the

Browse button.

4. After installing both the PSG/ESG Upgrade Assistant 5.12 program and the selected firmware files, proceed to “Using

the PSG/ESG Upgrade Assistant 5.12 with Firmware Files” on page 11.

To install PSG/ESG Upgrade Assistant 5.12

and firmware files from CD-ROM

1. Insert the firmware upgrade CD-ROM into the computer’s CD-ROM drive.

An autostart file should run automatically.

2. Once the PSG/ESG Upgrade Assistant 5.12 starts, proceed to “Using the PSG/ESG Upgrade Assistant 5.12 with

Firmware Files” on page 11.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Use the PSG/ESG Upgrade Assistant 5.12 with Firmware Files

The PSG/ESG Upgrade Assistant 5.12 is used with firmware files to upgrade the firmware on PSG/ESG signal generators.

NOTE For Agilent E44xxB ESG Signal Generators Models Only

When upgrading Agilent E44xxB ESG signal generators from firmware versions earlier than B.03.20, the

firmware must be upgraded in two steps:

a. Upgrade from earlier firmware versions to B.03.20 using RS-232.

b. Upgrade from B.03.20 to any newer version (> B.03.20) using RS-232 or GPIB.

1. From the program’s Setup Parameters dialog box, select the Connection Type to be either LAN, GPIB, or RS-232:

• If LAN is selected (not available with Agilent E44xxB ESG signal generators), specify the settings for LAN Setup.

Enter the IP address or the instrument name (alias name) that has been assigned to the signal generator.

For example, the signal generator could be assigned an instrument name or an IP address such as 141.xxx.xxx.xxx

(where each x can be any digit from 0 to 9). Each instrument name or IP address is assigned by a system

administrator at your facility. (For further information, refer to the documentation that came with your LAN

interface card or contact your system administrator.)

• If GPIB is selected, specify the settings for GPIB Setup. Use GPIB Port 0 and Address 19. These values should

correspond with the values that are set on your signal generator.

For example, the signal generator is usually set to GPIB Port 0 and Address 19 and the

GPIB interface card in the computer is usually set to GPIB Port 0 and Address 21. These values are chosen by

convention, but any address in the range 0-30, inclusive, may be used. (For further information, refer to the

documentation that came with your GPIB interface card.)

• If RS-232 is selected (only for use with Agilent E44xxB ESG signal generators), specify the settings for RS-232

Setup. Use either COM Port 1, 2, 3, or 4; the COM port that is selected depends on the number of serial ports that

are available on the PC model be used.

— Main firmware must be loaded at a Baud Rate of 19200, but DSP code can be loaded at Baud Rates up to 57600.

2. Under Firmware Release, click the Browse button.

3. From the Select Release File dialog box, double-click the folder for the version of firmware that you would like to

install (for example, double-click c_02_52_2002_nov).

4. When the folder opens, double-click the filename for the version of firmware that you would like to install (for example,

c_02_52_e443xc.esg).

a. Click the View Release Information button and review all firmware release information before downloading to the

signal generator.

b. From the program’s Setup Parameters dialog box, under Special Cases, select any items that may apply to the

upgrade:

• Select the Added New Hardware checkbox if new hardware has been added to the signal generator.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

• Select the Recover Failed Upgrade checkbox if a previous firmware upgrade had been aborted or failed and a

recovery is required.

c. Click the Next button to proceed.

5. From the program’s Select Components dialog box:

a. Under Selected Release, verify that the correct firmware version has been selected.

• If the firmware version needs to be changed, use the Back button and return to step 3 of this procedure.

b. Under Firmware Revision, verify that the version of the firmware designated as Installed is to be replaced by the

version designated as New.

• If an old version of firmware is to be installed, select the Allow Old Revisions checkbox. Note that installing

old versions of firmware with new hardware may generate errors.

c. Under Upgrade Selection, verify that all firmware components are to be upgraded.

By default, all upgrade components are selected:

• If you want to perform a partial upgrade and do not already know the requirements for each upgrade component,

use the Back button and return to step 4 of this procedure.

• If all components are not to be upgraded:

1. Click the Options button and review the cards installed in the signal generator along with their

corresponding options.

2. Click the OK button when done reviewing available options.

3. Click the components to be upgraded.

d. Click the Next button when all upgrade selections have been made.

6. From the program’s Confirm Upgrade dialog box, click the Next button to begin the firmware upgrade.

Note that once an upgrade is started, it should not be aborted and must be completed; failing to complete an upgrade

may leave the signal generator in a non-operational state.

The Upgrade in Progress area is displayed, indicating the estimated time remaining to complete the upgrade process.

7. When the download is completed, perform the “Check Signal Generator Functionality” procedure on page 5.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

ESG-B Firmware Installation For Versions <B.03.20

Introduction

The following procedure describes how to install firmware revisions into ESG-B RF Signal Generators with existing

firmware revisions <B.03.20. These instructions assume you are using Microsoft Windows and that you are familiar with

basic file management within Windows.

Required Equipment

•PC

• 9-pin null modem cable, with female connectors on both ends.

The 9-pin null modem cable can be made from a standard female-female 9-pin serial cable and a correctly-gendered null

modem adapter, or it can be assembled from the following parts:

Safety Considerations

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation.

Item Quantity Description Part Number

1 1 9-pin Serial RS-232 cable (male-female) 8120-6188

2 1 9-pin Null Modem Adapter (male-male) 5181-6639

3 1 9-pin gender changer (female-female) 1252-7825