Agilent Technologies 5062-8218 Installation and operation manual

Part Number 5967-8554 Supersedes: 5962-5078
Printed in USA September 2000
Installation Note
Time Gated Spectrum Analyzer
Capability Installation Kit, 5062-8218

Notice.
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies
shallnotbeliableforerrorscontainedhereinorforincidentalorconsequentialdamagesinconnectionwith
the furnishing, performance, or use of this material.
© Copyright Agilent Technologies, Inc 2000

Installation Note 5967-8554 3
Time Gated Spectrum Analyzer
Capability Installation Kit
Introduction
This installation note describes how to install Option 105, the time-gated spectrum analyzer capability
in an 8590 Series spectrum analyzer.
Installation Kit Parts List
Table 1 Parts Kit Option 105 Contents
Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . 8591E, 8593E, 8594E, 8595E and 8596E
spectrum analyzers
Serial Numbers:........................... 0000A00000/9999A99999
0000U00000/9999U99999
To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . Agilent Technologies Service Center Only
Estimated Installation Time:................ 1/2 Hour
Estimated Verification Time: . . . . . . . . . . . . . . . . . 1 Hour
Item Quantity Description Part Number
1 2 Nut, hex 15/32-32 0590-1251
2 1 Cable, BNC (m) to (m)* 8120-2682
3 1 Option 105 product note 5960-2555
4 2 Adapters, BNC female to male, right angle* 1250-0076
5 1 Cable BNC (f) to SMB (f) (gate in) 08591-60076
6 1 Cable BNC (f) to SMB (f) (gate out) 08591-60077
7 1 Installation note 5962-5078
* The right-angle adapters can be used to connect the BNC cable to the rear-panel connectors when
Option 105 is in use.

4 Installation Note 5967-8554
Tools Required
❏4-mm hex (Allen) wrench
❏9/16-inch nut driver
❏Needle-nose pliers (2 pairs required)
❏T-15 TORX screwdriver
❏T-10 TORX screwdriver
NOTE If the spectrum analyzer firmware is dated prior to 27.10.92 (October 27, 1992),
the spectrum analyzer firmware must be replaced with the firmware in the
firmware installation kit. To determine the firmware date on the analyzer, turn
the analyzer power off, then the analyzer power on. The firmware date is
displayed on the analyzer screen. The firmware is displayed in a day.month.year
format. See Contacting Agilent Technologies for details.
WARNING Before disassembling the instrument, turn the power switch OFF and
unplug the analyzer. Failure to unplug the analyzer can result in
personal injury.
CAUTION Electrostatic discharge (ESD) can damage or destroy electronic
components. All work on electronic assemblies should be performed at a
static-safe work station. Refer to the installation and verification manual
for your spectrum analyzer for information about a static-safe work
station and static-safe accessories.
Procedure
Removing the Instrument Cover
1. Disconnect the analyzer from ac power.
CAUTION To prevent damage to the front panel, place a soft cloth or towel between the work
surface and the front panel.
2. Carefully place the analyzer on the work surface with the front panel facing down.
3. Remove the four screws and washers attaching the instrument cover to the rear frame.
4. Unscrew, but do not remove, the four rear-feet screws, using a 4-mm hex wrench.

Installation Note 5967-8554 5
Figure 1 Removing The instrument Cover
5.Pull the instrument cover off toward the rear of the instrument.
6.If there is a dual I/O option on the back of the instrument it must be removed. If the instrument
does not have the dual I/O option, then go to step 9.
7.Remove the five screws attaching the dual I/O to the rear panel.
8.Remove dual I/O connector board from the instrument by pulling up on the board.
9.Remove three screws on each side of the rear panel, and pull the rear panel gently away from the
instrument a few centimeters.
10.RemovetheplugsfromtheGateTriggerInandGateOutholesontheanalyzerrearpanel.Useone
pair of long needle-nose pliers to compress the barrel of the plug, and use another pair of needle-
nose pliers to pull the plug out of the rear panel. See Figure 2.

6 Installation Note 5967-8554
Figure 2 Gate Trigger Input and Gate Output
11.This installation kit comes with two long cables and two hex nuts. Install the cable with the #6 label
through the rear-panel GATE TRIGGER INPUT (1) opening. Use a hex nut to attach the cable to
the rear panel. Tighten the hex nut with the hex wrench.
12.Install the other cable with the #0 label through the rear-panel GATE OUTPUT (2) opening. Use a
hex nut to attach the cable to the rear panel. Tighten the hex nut with the hex wrench.
13.Remove the 4 screws attaching the Dual I/O interconnect board A40 to the CPU and remove the I/O
board.
14.Route the SMB cable ends to enable them to attach to A16J501 and A16J500.
NOTE If J501 and J500 do not exist on the CPU, you will need to order a CPU Board Kit.
Refer to Contacting Agilent Technologies section of this document.
15.Being careful not to pinch or damage any of the cables, reattach the rear panel assembly to the
chassis of the analyzer.

Installation Note 5967-8554 7
Figure 3 Attaching Cables to Board Assembly

8InstallationNote5967-8554
16.Attach the cable from the rear-panel connector labeled GATE TRIGGER INPUT to A16J501. See
Figure 3.
17.Attachthecablefromtherear-panelconnectorlabeledGATETRIGGEROUTPUTtoA16J500.See
Figure 3.
18.Reattach I/O board to CPU. Be careful not to pinch the SMB cable.
19.If the instrument has the dual I/O option, then it should be reattached. Make sure that the
connector is properly aligned, then firmly push into place. Replace the five screws attaching the
dual I/O to the rear panel.
CAUTION Be careful not to bend or misalign the connector pins.
Replacing the Instrument Cover
CAUTION To prevent damage when replacing the instrument cover, place a soft cloth or
towel between the work surface and the front panel.
Ensurecablesdonotbindbetweentheinstrumentcoverandtheanalyzerinternal
assemblies.
20.Carefully place the analyzer on the work surface with the front panel facing down.
21.Replace the instrument cover assembly. The seam of the cover should be on the bottom side of the
analyzer.
22.Tighten the four rear-feet screws with a 4-mm hex wrench.
23.Replace the four screws and washers attaching the instrument cover assembly to the rear frame.
Contacting Agilent Technologies
1.If the CPU board does not have J501 and J500, order the 08590-60361 CPU kit for a compatible
CPU board.
2.To complete the Option 105 upgrade process refer to the Web at http://mktwww.soco.agilent.com/
field/service/signal/8590/105revb.htmtoreceiveacompletesetofinstructionsorcall(707)577-6801.
3.For detailed information about the 8590 Series firmware history, look on the Web at http://
mktwww.soco.agilent.com/field/service/signal/8590/firmhist.htm. The two different firmware kits
are noted on this web page.