Agilent Technologies PSA Series Installation and operation manual

Part Number E4440-90072
PrintedinUSA May2002
Agilent PSA Spectrum Analyzer
Flash Memory Installation Kit
Installation Note

Notice.
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies
shall not be liable for errors contained herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material.
© Copyright 2001− 2002 Agilent Technologies, Inc.

Installation Note E4440-90072 3
Flash Memory Installation Kit
Introduction
This installation kit includes the latest Flash memory assembly and a CD that contains the
latest instrument firmware and measurement personalities. The replacement Flash board
has been preloaded with the operating system and core instrument firmware only. Therefore,
if your instrument requires optional measurement personalities, you must reload them from
the CD included with this kit or from the Agilent PSA web site.
NOTE All user stored files such as instrument states or traces from the original Flash
assembly will be lost.
CAUTION The following procedure must be done at a static safe work area.
Installation Kit Parts List
Contents of Flash Memory Upgrade Kit
ProductsAffected: ........................ PSAE4440A
PSA E4443A
PSA E4445A
PSA E4446A
PSA E4448A
SerialNumbers:.......................... US00000000/US99999999
MY00000000/MY99999999
ToBePerformedBy: ...................... (X)AgilentServiceCenter
(X) Personnel Qualified by Agilent
(X) Customer
EstimatedInstallationTime: ...............
EstimatedVerificationTime: ...............
1Hour
0.5 Hours
Quantity Description Agilent Part Number
1 64 MB Flash board Not available separately
4 Stand-offs 0380-4163
1 Firmware Update Kit E4440-60087
1 Installation Note this note

4 Installation Note E4440-90072
Tools Required
 Microsoft â Windows â based Personal Computer with Local Area Network (LAN) card.
 Windows NT â 4.0 or greater, Windows â 98
 CD-ROM drive
 Printer compatible with the PSA or DOS formatted 3.5” floppy disk. (Optional)
The following hand tools are required:
WARNING This is a Safety Class 1 Product (provided with a protective earthing
ground incorporated in the power cord). The mains plug shall only be
inserted in a socket outlet provided with a protected earth contact. Any
interruption of the protective conductor inside or outside of the
product is likely to make the product dangerous. Intentional
interruption is prohibited.
WARNING The power cord is connected to internal capacitors that may
remain live for 5 seconds after disconnecting the plug from it’s
power supply.
WARNING The detachable power cord is the instrument disconnecting device. It
disconnects the mains circuits from the mains supply before other parts
of the instrument. The front panel switch is only a standby switch and is
not a LINE switch (disconnecting device).
WARNING The opening of covers or removal of parts is likely to expose dangerous
voltages. Disconnect the product from all voltage sources before
starting to open.
WARNING These servicing instructions are for use by qualified personnel only. To
avoid electrical shock, do not perform any servicing unless you are
qualified to do so.
Microsoft â ,Windows â , and Windows NT â are US registered trademarks of Microsoft Corporation.
Description Agilent Part Number
TORX Hand Driver - Size T10 8710-1623
TORX Hand Driver - Size T20 8710-1615
Diagonal cutters N/A

Installation Note E4440-90072 5
Installation Procedure
If the instrument is functioning well enough to view the instrument configurations on screen,
these configurations should be printed or copied down.
The Flash memory board is attached to the CPU assembly, so it is necessary to remove this
assembly. The CPU assembly slides into the instrument from the rear panel, plugs directly
into the motherboard, and is held in place with screws on the CPU plate. The CPU assembly
cannot be removed without removing other assemblies. Perform the following procedures in
order:
1. Remove the instrument outer case.
2. Remove the instrument top brace.
3. Remove the A6 SCSI board.
4. Remove the A7 Digital IF assembly.
5. Remove the A26 CPU assembly.
6. Replace the A26A2 Flash board on the CPU assembly.
7. Install the CPU assembly into the chassis.
8. Install the Digital IF assembly and SCSI board.
9. Install the instrument top brace and outer case.
10.Install the option designators and license keywords (if necessary).
11.Install the option firmware.
Since the Flash memory does not contain calibration data, and the instrument will perform
an auto align when powered up, instrument re-calibration should not be required following
this repair. The installation of the hardware should take about 1 hour to complete.
Installation of optional measurement personalities and re-licensing varies with the number of
options.
For assistance at any time during this procedure, get in touch with your nearest Agilent
Technologies Sales and Service Office. To find your local Agilent office access the following
URL or call the following telephone number:
http://www.agilent.com/find/assist
1-800-452-4844 (8am-8pm EST)

6 Installation Note E4440-90072
Capture Configuration Information (if possible)
NOTE If the instrument is able to boot and display the softkey menus, it should be
possible to gather information using the following process. This procedure will
provide a record of the options with the associated license keys as well as I/O
configurations for the purpose of installing them into the new 64 MB Flash
board.
1. Power on the PSA.
2. Connect a printer to the PSA. If a printer is unavailable, you can save the configuration
information to the PSA floppy disk (drive A:), then place the floppy in your computer and
print. If there is no way to provide a print out, then you must carefully write down the
instrument information on a piece of paper.
To set up the PSA to save a screen file to the floppy:
insert a DOS formatted floppy into the PSA disk drive.
Press File,Save,Dir Select,choose[-A-],pressDir Select again to read the directory.
Press the Type key and select Screen.PressSave Now.
NOTE Although you will not need this first saved screen, the process of saving this first
screen enables future screen saves.
3. On the PSA press System,More,More,Licensing,Show License to display the list of loaded
firmware options and their associated license keywords. Press the Print key to print this
list, or press the Save key to save it to a floppy disk, or manually copy the options and the
associated license keys.
4. Press System,More,Show System. Under the Options heading, you can see the designators
for the hardware and firmware options. Hardware options are; 1DS (preamp), B7J
(electronic attenuator), and BAB (APC 3.5 mm connector). Press the Print key to print this
list, or press the Save key to save it to a floppy disk, or manually copy the option
designators.
5. Press System,Configure I/O.PressthePrint key to print this list, or press the Save key to
save it to a floppy disk, or manually copy all softkey labels such as IP Address and Host
Name.
6. If you saved the configuration information to the floppy, print out the files now to assure
they are correct.

Installation Note E4440-90072 7
Instrument Outer Case
CAUTION If the instrument is placed on its face during any of the following procedures, be
sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or
input connector.
Removal
1. Disconnect the instrument from ac power.
2. There are two handles on the sides of the instrument that must be taken off. Refer to
Figure 1. Using the T-20 driver, loosen the screws that attach each handle (1). Remove the
handles.
3. Remove the four bottom feet (2). This is done by lifting up on the tabs on the feet, and
sliding the feet in the direction indicated by the arrows.
4. Remove the four screws (3) that hold the rear feet (4) in place.
5. Pull the instrument cover (5) off towards the rear of the instrument.
Figure 1 Instrument Outer Case Removal

8 Installation Note E4440-90072
Top Brace
Removal
1. Using the T-10 driver, remove the top screws (3) (one screw is under the security label)
and the side screws (2) attaching the top brace (1) to the deck. Refer to Figure 2.
2. The top brace can now be removed from the deck.
Figure 2 Top Brace

Installation Note E4440-90072 9
A6 SCSI Board
Removal
1. Refer to Figure 3. At the rear of the instrument, use a T-10 driver to remove the 6 screws
(1) securingthesmallpaneltotheframe.
2. The SCSI board can be removed through the rear panel by pulling up on the board to
disengage it from the CPU board.
Figure 3 SCSI Board Removal

10 Installation Note E4440-90072
A7 Digital IF Assembly
Figure 4 shows the location of the A7 Digital IF assembly in slot 4.
Figure 4 Vertical Board Assembly Locations
Removal
The cables that connect to this assembly do not need to be removed since you are going to pull
the assembly out of the chassis and lay it down on the instrument. Use the board ejectors
located on the Digital IF assembly to carefully pull it out of the chassis.
If there are any other assemblies in slots 2 and 3, remove them now.