Agilent Technologies U1401B User manual

Agilent Technologies
U1401B
Handheld
Multi-Function
Calibrator/Meter
User’s and Service Guide

U1401B User’s and Service Guide
Notices
© Agilent Technologies, Inc. 2009 - 2012
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
U1401-90055
Edition
Seventh Edition, September 12, 2012
Printed in Malaysia
Agilent Technologies, Inc.
5301 Stevens Creek Blvd.
Santa Clara, CA 95051 USA
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
U.S. Government Restricted Rights. Soft-
ware and technical data rights granted to
the federal government include only those
rights customarily provided to end user cus-
tomers. Agilent provides this customary
commercial license in Software and techni-
cal data pursuant to FAR 12.211 (Technical
Data) and 12.212 (Computer Software) and,
for the Department of Defense, DFARS
252.227-7015 (Technical Data - Commercial
Items) and DFARS 227.7202-3 (Rights in
Commercial Computer Software or Com-
puter Software Documentation).
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.

U1401B User’s and Service Guide III
Safety Symbols
The following symbols on the instrument and in the documentation
indicate precautions which must be taken to maintain safe
operation of the instrument.
Direct current (DC) Off (supply)
Alternating current (AC) On (supply)
Both direct and alternating current Caution, risk of electric shock
Three-phase alternating current Caution, risk of danger (refer to this manual
for specific Warning or Caution information)
Earth (ground) terminal Caution, hot surface
Protective conductor terminal Out position of a bistable push control
Frame or chassis terminal In position of a bistable push control
Equipotentiality Category II 150 V overvoltage protection
Equipment protected throughout by
double insulation or reinforced
insulation
CAT II
150 V

IV U1401B User’s and Service Guide
General Safety Information
The following general safety precautions must be observed during all
phases of operation, service, and repair of this instrument. Failure to
comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended
use of the instrument. Agilent Technologies assumes no liability for the
customer’s failure to comply with these requirements.
WARNING
• When working above DC 60 V, AC 30 Vrms or AC 42.4 Vpeak, exercise caution
– these ranges pose a shock hazard.
• Do not measure more than the rated voltage (as marked on the instrument)
between terminals, or between terminal and earth ground.
• Double-check the instrument operation by measuring a known voltage.
• This instrument is designed for measurement under CAT II 150 V. Avoid
measuring power mains with voltage exceeding 150 V.
• For current measurement, turn off circuit power before connecting the
instrument to the circuit. Always place the instrument in series with the
circuit.
• When connecting probes, always connect the common test probe first. When
disconnecting probes, always disconnect the live test probe first.
• Detach test probes from the instrument before you open the battery cover.
• Do not use the instrument with the battery cover or part of the cover removed
or loose.
• Recharge or replace the battery as soon as the low battery indicator
flashes on screen. This is to avoid false readings, which may lead to possible
electric shock or personal injury.
• Do not use the instrument if it is damaged. Before you use the instrument,
inspect the casing. Look for cracks or missing plastic. Do not operate the
instrument around explosive gas, vapor, or dust.
• Inspect the test probes for damaged insulation or exposed metal, and check
for continuity. Do not use the test probe if it is damaged.
• Do not use any other AC charger adapter apart from the one certified by
Agilent with this product.
• Do not use repaired fuses or short-circuited fuse-holders. For continued
protection against fire, replace the line fuses only with fuses of the same
voltage and current rating and recommended type.
• Do not service or perform adjustments alone. Under certain condition,
hazardous voltages may exist, even with the equipment switched off. To avoid
dangerous electric shock, service personnel must not attempt internal service
or adjustment unless another person, capable of rendering resuscitation or
first aid, is present.

U1401B User’s and Service Guide V
WARNING
• Do not substitute parts or modify equipment to avoid the danger of introducing
additional hazards. Return the product to the nearest Agilent Technologies
Sales and Service Office for service and repair to ensure the safety features
are maintained
• Do not operate damaged equipment as the safety protection features built into
this product may have been impaired, either through physical damage,
excessive moisture, or any other reason. Remove power and do not use the
product until safe operation can be verified by service-trained personnel. If
necessary, return the product to the nearest Agilent Technologies Sales and
Service Office for service and repair to ensure the safety features are
maintained.
CAUTION
• Turn off circuit power and discharge all high-voltage capacitors in the
circuit before you perform resistance and capacitance measurements
or continuity and diode tests.
• Use the correct terminals, function, and range for your measurements.
• Do not measure voltage when current measurement is selected.
• Use only the recommended rechargeable battery. Ensure proper
insertion of battery in the instrument, and follow the correct polarity.
• Disconnect test leads from all the terminals during battery charging.

VI U1401B User’s and Service Guide
Environmental Conditions
This instrument is designed for indoor use and in areas with low
condensation. The table below shows the general environmental
requirements for this instrument.
Environmental conditions Requirements
Operating temperature Full accuracy from 0 °C to 40 °C
Operating humidity Full accuracy up to 80% R.H. (relative
humidity) for temperature up to 31 °C,
decreasing linearly to 50% R.H. at 40 °C
Storage temperature –20 °C to 60 °C (with battery removed)
Storage humidity 5% to 80% R.H. non-condensing
Altitude Up to 2000 m
Pollution degree Pollution Degree 2
CAUTION
The Handheld Multi-Function Calibrator/Meter complies with the
following safety and EMC requirements.
•IEC 61010-1:2001/EN61010-1:2001 (2nd Edition)
•Canada: CAN/CSA-C22.2 No. 61010-1-04
•USA: ANSI/UL 61010-1:2004
•IEC61326-2-1:2005/EN61326-2-1:2006
•Canada: ICES/NMB-001:2004
•Australia/New Zealand: AS/NZS CISPR11:2004
CAUTION
Degradation of some product specifications can occur in the presence of
ambient electromagnetic (EM) fields and noise that are coupled to the
power line or I/O cables of the instrument. The instrument will self-recover
and operate to all specifications when the source of ambient EM field and
noise are removed or when the instrument is protected from the ambient
EM field or when the instrument cabling is shielded from the ambient EM
noise.

U1401B User’s and Service Guide VII
Regulatory Markings
The CE mark is a registered trademark
of the European Community. This CE
mark shows that the product complies
with all the relevant European Legal
Directives.
The C-tick mark is a registered
trademark of the Spectrum
Management Agency of Australia. This
signifies compliance with
the Australia EMC Framework
regulations under the terms of the
Radio Communication Act of 1992.
ICES/NMB-001 indicates that this ISM
device complies with the Canadian
ICES-001.
Cet appareil ISM est confomre a la
norme NMB-001 du Canada.
This instrument complies with the
WEEE Directive (2002/96/EC) marking
requirement. This affixed product label
indicates that you must not discard this
electrical or electronic product in
domestic household waste.
The CSA mark is a registered
trademark of the Canadian Standards
Association.

VIII U1401B User’s and Service Guide
Waste Electrical and Electronic Equipment (WEEE) Directive
2002/96/EC
This instrument complies with the WEEE Directive (2002/96/EC)
marking requirement. This affixed product label indicates that you
must not discard this electrical or electronic product in domestic
household waste.
Product Category:
With reference to the equipment types in the WEEE directive Annex
1, this instrument is classified as a “Monitoring and Control
Instrument” product.
The affixed product label is as shown below.
Do not dispose in domestic household waste
To return this unwanted instrument, contact your nearest Agilent
Technologies, or visit:
www.agilent.com/environment/product
for more information.
Agilent Technologies, through Rechargeable Battery Recycling Corporation (RBRC), offers free and
convenient battery recycling options in the U.S. and Canada. Contact RBRC at 877-2-RECYCLE
(877.273.2925) or online at: http://www.call2recycle.org/ for the nearest recycling location.

U1401B User’s and Service Guide IX
In This Guide...
1Getting Started
This chapter contains a brief description of the U1401B Handheld
Multi-Function Calibrator/Meter front panel, rotary switch, keypad,
display, terminals, and rear panel.
2Calibrator Output Operations
This chapters contains detailed information on how to generate
signals using the U1401B.
3Making Measurements
This chapter contains the detailed information on how measurements
are taken using the U1401B.
4Changing the Default Settings
This chapter describes how to change the default settings of the
U1401B.
5Application Examples
This chapter describes some application examples for the U1401B.
6Maintenance
This chapter will help you troubleshoot the U1401B for faults.
7Performance Tests and Calibration
This chapter contains the performance test procedures and
adjustment procedures to help you ensure that the U1401B is
operating within its published specifications.
8Specifications
This chapter details the specifications of the U1401B.

X U1401B User’s and Service Guide
Declaration of Conformity (DoC)
The Declaration of Conformity (DoC) for this instrument is available on the
Web site. You can search the DoC by its product model or description.
http://regulations.corporate.agilent.com/DoC/search.htm
NOTE
If you are unable to search for the respective DoC, please contact your
local Agilent representative.