Agri-Fab 45-01797 User manual

45-01797
SAFETY PRECAUTIONS SPECIFICATIONS
Roller Drum: 24" Dia. x 36" Wide, Welded Steel
O.A. Width: Approximately 40"
Bearings: 1" I.D., Replaceable
Tow Hitch: Std. Pin Type - 1/2" Hole
Weight w/ Water: Up to 640 Lbs. Filled with Water
Approx. Sh. Wt.: Approximately 105 Lbs.
PRINTED IN U.S.A. Form No. 45639 (09/20/18)
1. Never attach a garden hose to the ll/drain hole when lling.
Dangerous pressure build up could occur inside roller.
2. Never ll roller to maximum weight without checking capability
of vehicle to safely pull and stop. Refer to the towing vehicle
owners manual.
3. Never use roller up and down hills; always work across hills
and slopes.
4. Never use roller on slopes greater than 10°. Refer to included
Slope Guide.
5. Never allow children to operate towed equipment.
6. Never allow children or others on towed equipment
7. Always use caution when turning, slowing, or stopping.
8. Always drain roller to keep from freezing.
9. Always keep the area clear of bystanders; paying close
attention to children and pets.

ASSEMBLY INSTRUCTIONS
(SEE ILLUSTRATION BELOW)
1. Assemble bearings (Ref. 5) into hitch tubes (Ref. 3) so
that bearing ange is against outside of hitch tube. You
may need to place a block of wood against bearing
and carefully tap with a hammer.
2. Place hitch tubes (Ref. 3) onto both ends of roller shaft.
Assemble a at washer (Ref. 6) onto each end of roller
shaft and secure with two cotter pins (Ref. 12).
3. Assemble scraper bar (Ref. 2) to hitch tubes (Ref. 3)
using two hex bolts (Ref. 9), spacers (Ref 15), and hex
lock nuts (Ref. 10). Do not tighten yet.
4. Assemble ends of hitch tubes (Ref. 3) together using
two hex bolts (Ref. 7) and hex lock nuts (Ref. 10). Do
not tighten yet.
5. Assemble hitch brackets (Ref. 4) to hitch tubes (Ref. 3)
using two hex bolts (Ref. 8) and hex lock nuts (Ref. 10).
Do not tighten yet.
6. Tighten bolts and nuts starting with scraper bar (Ref.
2), then ends of hitch tubes (Ref. 3), and nally hitch
brackets (Ref. 4).
7. Install hitch pin (Ref. 13) through hitch brackets (Ref. 4)
and secure with hair cotter pin (Ref. 14).
8. Adjust plug (Ref. 11) size by twisting handle. Lock a plug
in each end of roller drum by ipping handle down.
1 ----- 1 Roller Drum (Not sold separately)
2 24867 1 Scraper Bar
3 48361 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 47810 6 Hex Lock Nut, 5/16-18
11 49467 2 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
15 23625 2 Spacer
Ref. Part Qty. Description
No. No.
Ref. Part Qty. Description
No. No.
1
1111 23
3
4
5
5
6
67
8
9
9
10
10
15
15
12
12
10
13
14
10
Instructions for tightenting plug
■ Pull plug rmly in opposing directions
■ Twist ring counter-clockwise to tighten
NOTE: If the outer washer is not functioning properly, use a pair of
needlenose pliers to ensure that it is free.
Plug Adjustment

A POWER POLE
A CORNER OF A BUILDING
OR A FENCE POST
FOLD ALONG DOTTED LINE, REPRESENTING A 10 DEGREE SLOPE
SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
© 2018 Agri-Fab, Inc.
the fastest way to purchase parts
www.speedepart.com