Agri-Fab 45-02168 User manual

45-02168
FORM NO. 3-125 (06/08/21)
SAFETY PRECAUTIONS
1. Never attach a garden hose to the ll/drain hole when lling.
Dangerous pressure build up could occur inside roller.
2. Never ll roller to maximum weight without checking capability of
vehicle to safely pull and stop. Refer to the towing vehicle owners
manual.
3. Never use roller up and down hills; always work across hills and
slopes.
4. Never use roller on slopes greater than 10°. Refer to included
Slope Guide.
5. Never allow children to operate towed equipment.
6. Never allow children or others on towed equipment
7. Always use caution when turning, slowing, or stopping.
8. Always drain roller to keep from freezing.
9. Always keep the area clear of bystanders; paying close
attention to children and pets.
youtube.com/c/agrifab
Video
Instruction
Guide
Want more information or assembly tips?
SPECIFICATIONS
Roller Drum: 24" Dia. x 48" Wide, Welded Steel
O.A. Width: Approximately 52"
Bearings: 1" I.D., Replaceable
Tow Hitch: Std. Pin Type - 1/2" Hole
Weight w/ Water: Up to 910 Lbs. Filled with Water
Approx. Sh. Wt.: Approximately 114 Lbs.

ASSEMBLY INSTRUCTIONS
(SEE ILLUSTRATION BELOW)
Figure 1.
1. Pull plug rmly in opposing directions
2. Twist ring counter-clockwise to tighten
NOTE: If the outer washer is not functioning properly, use a
pair of needlenose pliers to ensure that it is free.
PLUG ADJUSTMENT
(SEE FIGURE 1)
1. Assemble a plastic bearing (7) into a hitch tube (2) so
that the bearing ange is against the outside of the hitch
tube. You may need to place a block of wood against
bearing and carefully tap with a hammer.
2. Place a cotter pin (12) into the inside hole of the axle.
3. Slide the washer (6), spacer (3), hitch tube (2), washer
(6) onto the axle.
4. Place cotter pin (12) into the outside hole of the axle.
5. Repeat steps 1 through 4 on the other side.
6. Bring the two hitch tubes together using three 5/16 X 3"
hex bolts (8) and 5/16" nuts (10). Do not tighten yet.
7. Assemble hitch brackets (1) to hitch tubes ( 2) using two
5/16 X 2-1/4" hex bolts (4) and 5/16" nylock nuts (10).
Do not tighten yet.
8. Tighten all bolts and nuts starting with hitch tubes (2),
ending with hitch brackets (1).
9. Install hitch pin (9) through hitch brackets (1) and secure
with hair cotter pin (5).
10. Adjust plug (11) size by twisting handle. Lock a plug in
each end of roller drum by ipping handle down.
1
2
3
3
4
5
6
6
6
6
7
7
88
2
9
10
10
10
11
12
12
12
12
ROLLER WILL CHANGE HANDLING AND
BRAKING OF VEHICLE, ESPECIALLY ON
SLOPES. FOLLOW TOWING GUIDELINES IN
ROLLER AND TOWING VEHICLES OWNER’S
MANUALS.
DO NOT EXCEED SLOPES GREATER THAN 10°
REF PART NO. QTY DESCRIPTION
1 24192BL1 2 Bracket, Hitch (Straight)
2 2-257BL3 2 Tube, Hitch (Roller)
3 40740 2 Spacer, 1.28 ID x 2.0
4 43224 2 Bolt, Hex 5/16-18 x 2-1/4"
5 43343 1 Pin, Hair Cotter
6 43528 4 Washer, 1" SAE 1.06
7 43632 2 Bearing, Plastic
8 46782 3 Bolt, Hex 5/16-18 x 3"
REF PART NO. QTY DESCRIPTION
9 47623 1 Pin, Hitch 3/8 x 3"
10 47810 5 Nut, 5/16-18 Nylock
11 49467 2 Plug, Roller (1-1/4)
12 714-0117 4 Pin, Hair Cotter 5/32
1 Assembly, 24x48 Roller
3-125 1 Owner's Manual
45906 1 Roller Caution Label

A POWER POLE
A CORNER OF A BUILDING
OR A FENCE POST
FOLD ALONG DOTTED LINE, REPRESENTING A 10 DEGREE SLOPE
SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
© 2021 Agri-Fab, Inc.