Agri-Fab 45-0290 User manual

• Safety
• Assembly
• Operation
• Maintenance
• Parts
38" Heavy Duty
LAWNSWEEPER
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
PRINTED IN .S.A. FORM NO. 47548 (REV. 12/99)
OWNERS
MANUAL
Model No.
45-0290

2
6. Vehicle braking and stability may be affected with the
attachment of this sweeper. Do not fill sweeper to
maximum capacity without checking the capability of
the towing vehicle to safely pull and stop with the
sweeper attached. Stay off of steep slopes.
7. Stop and inspect vehicle and sweeper for damage
after striking an object. Repair any damage before
continuing operation.
8. Keep sweeper away from fire. Excessive heat can
damage the brushes and hopper bag and could
cause the bag and its contents to burn.
9. Before storing the sweeper, always empty the hopper
bag to avoid spontaneous combustion.
10. Follow maintenance and lubrication instructions as
outlined in the maintenance section of this manual.
1. Read the vehicle and sweeper owners manuals and
know how to operate your vehicle and sweeper
before using this sweeper attachment. Always in-
struct other users before they operate the sweeper.
2. Do not permit children to operate sweeper.
3. Do not permit anyone to ride on sweeper.
4. Never attach the hopper rope to any part of your body
or clothing! Never hold onto the rope while towing the
sweeper! Attach the rope to the towing vehicle to
keep it away from wheels and rotating parts.
5. Operate the sweeper at reduced speed on rough
terrain, near ditches and on hillsides to prevent loss
of control.
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate
the equipment. Exercise caution at all times, when using power equipment.
MAINTENANCE..............................................................12
STORAGE.......................................................................12
SERVICE AND ADJ STMENTS....................................13
TRO BLESHOOTING....................................................13
REPAIR PARTS EXPLOSION........................................14
REPAIR PARTS LIST.....................................................15
SAFETY R LES...............................................................2
F LL SIZE HARDWARE CHART.....................................3
CARTON CONTENTS......................................................4
SWEEPER ASSEMBLY INSTR CTIONS........................5
HOPPER ASSEMBLY INSTR CTIONS..........................7
KNOW YO R SWEEPER...............................................11
HOW TO SE YO R SWEEPER...................................11
Look for this symbol to point out important safety precautions. It means--Attention!!
Become alert!! Your safety is involved.
SAFETY
TABLE OF CONTENTS

3
HARDWARE PACKAGE CONTENTS
REF. QTY. DESCRIPTION
P 2 Palnut, 3/8"
Q 1 Flat Washer, 5/16" Std. Wrt.
R 2 Flat Washer, 5/16" (Small)
S 6 Lock Washer, 5/16"
T 1 Lock Washer (Tooth), 5/16"
1 Hairpin Cotter, 1/8"
V 2 Hairpin Cotter, 3/32"
W 2 Clevis Pin, 3/8" x 3/4"
X 1 Spacer Bushing,
Y 2 Hitch Spacer, 3/4"
Z 4 Hopper Mount Clamp
AA 1 Grip
BB 1 Knob, Plastic
CC 1 Hitch Pin
A 2 Hex Bolt, 5/16-18 x 3" Lg.
B 2 Hex Bolt, 5/16-18 x 2-1/4" Lg.
C 2 Hex Bolt, 5/16-18 x 1-3/4" Lg.
D 2 Hex Bolt, 1/4-20 x 1-1/4" Lg.
E 2 Hex Bolt, 5/16-18 x 1" Lg.
F 2 Hex Bolt, 3/8-16 x 3/4" Lg.
G 4 Hex Bolt, 5/16-18 x 3/4" Lg.
H 1 Carriage Bolt, 5/16-18 x 3/4" Lg.
I 2 Curved Head Bolt, 1/4-20 x 1" Lg.
J 6 Slotted Screw, #10-32 x 5/8" Lg.
K 2 Hex Lock Nut, 3/8"
L 8 Hex Lock Nut, 5/16"
M 4 Hex Nut (Plain), 5/16"
N 4 Hex Lock Nut, 1/4"
O 6 Hex Lock Nut, #10-32
REF. QTY. DESCRIPTION
A B C D EF G HI
K
L
M
N
O
P
U
V
S
QR
AA
ZBB CC
T
W
X Y
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
J

4
ASSEMBLY
10. Hopper Bag
11. Windscreen
12. pper Hopper Tube, R.H.
13. pper Hopper Tube, L.H.
14. Lower Hopper Tube, R.H.
15. Lower Hopper Tube, L.H.
16. Hopper Bag Pivot Rod
17. Hopper Support Rod (2)
18. Bag Retaining Strap
19. Bag Frame Strap
1. Sweeper Housing Assembly
2. Bag Arm (2)
3. Hitch Tube, L.H.
4. Hitch Bracket
5. Hitch Bracket (Straight)
6. Height Adjustment Strap
7. Height Adjustment Handle
8. Hitch Tube, R.H.
9. Rope
CARTON CONTENTS
1
4
5
6
7
9
10
11
12
14 15
16
17
18 19
13
2
3
8
2
CARTON CONTENTS (Loose Parts in Carton)

5
FIGURE 2
FIGURE 3
If your tractor hitch has 10" to 13" ground clear-
ance use the instructions below to assemble the
sweeper hitch brackets. If your tractor hitch has
less than 10" ground clearance, go to page 6.
4. Assemble the bent hitch bracket on top and the
straight hitch bracket to the bottom of the hitch tubes.
Fasten with two 5/16" x 2-1/4" hex bolts and 5/16" hex
lock nuts as shown in figure 3. The bolts should
straddle the front hitch tube bolt. Do not tighten yet.
5. At this time tighten the four bolts fastening the hitch
tubes to the sweeper housing. Next, tighten the two
bolts fastening the hitch tubes together. Finally,
tighten the two bolts fastening the hitch brackets to
the hitch tubes.
6. Assemble the hitch pin, two 3/4" spacers and the
1/8" hairpin cotter to the hitch brackets. See figure 3.
5/16" HEX LOCK NUT
HITCH BRACKET
(STRAIGHT)
HITCH
BRACKET
HITCH PIN
5/16" x 2-1/4"
HEX BOLT
3/4" SPACERS
1/8" HAIRPIN
COTTER
5/16" x 3"
HEX BOLT
5/16" LOCK
WASHER
5/16" HEX
LOCK NUT
SPACER
BUSHING
HEIGHT
ADJUSTMENT
STRAP
5/16" FLAT
WASHER
(SMALL)
3. Place the spacer bushing into the hole in the height
adjustment strap. Place the strap with the bushing
between the hitch tubes, aligned with the rear hole.
Fasten the hitch tubes together, with the strap and
bushing between them, using two 5/16" x 3" hex
bolts, 5/16" flat washers (smaller), 5/16" lock
washers and 5/16" hex lock nuts. Do not tighten yet.
See figure 2.
TOOLS REQUIRED FOR ASSEMBLY
(1) Pliers
(1) Screwdriver
(1) Hammer
(1) Adjustable Wrench
(1) 9/16" Open End or Box End Wrench
(1) 1/2" Open End or Box End Wrench
(1) 7/16" Open End or Box End Wrench
(1) 3/8" Open End or Box End Wrench
REMOVAL OF PARTS FROM CARTON
Remove the sweeper, the loose parts and the hardware
package from the carton. Lay out the parts and hardware
as shown on pages 3 and 4.
ASSEMBLY OF SWEEPER
Note: Right hand (R.H.) and left hand (L.H.) are deter-
mined from the operators position while seated on the
tractor.
1. Cut off the plastic tie holding the height adjustment
tube in place. See figure 1.
2. Assemble the R.H. and L.H. hitch tubes to the sweeper
housing using two 5/16" x 1-3/4" hex bolts, two 5/16"
x 1" hex bolts, four 5/16" lock washers and four 5/16"
hex nuts. Do not tighten yet. See figure 1.
5/16" LOCK
WASHER
5/16" x 1"
HEX BOLT
HITCH TUBE (L.H.)
PLASTIC TIE
5/16" HEX NUT
5/16" x 1-3/4"
HEX BOLT
FIGURE 1

6
FIGURE 6
FIGURE 5
FIGURE 4
If your tractor hitch has 8" to 10" ground clear-
ance, use the instructions below to assemble the
sweeper hitch brackets. If your tractor hitch has
more than 10" ground clearance, refer back to
page 5.
7. Assemble the bent hitch bracket to the bottom and
the straight hitch bracket on top of the hitch tubes.
Fasten with two 5/16" x 2-1/4" hex bolts and two 5/16"
hex lock nuts as shown in figure 4. The bolts should
straddle the front hitch tube bolt. Do not tighten yet.
8. At this time tighten the four bolts fastening the hitch
tubes to the sweeper housing. Next, tighten the two
bolts fastening the hitch tubes together. Finally,
tighten the two bolts fastening the hitch brackets to
the hitch tubes.
9. Assemble the hitch pin, two 3/4" spacers and the
1/8" hairpin cotter to the hitch brackets. See figure 4.
5/16" HEX
LOCK NUT
HITCH PIN
HITCH
BRACKET
5/16" x 2-1/4"
HEX BOLT
HITCH
BRACKET
(STRAIGHT)
HAIRPIN COTTER
3/4" SPACERS
10. Assemble the height adjustment handle to the height
adjustment tube using the curved bolts, washers and
nuts which come pre-assembled to the tube. Tighten
the height adjustment handle so that the height
adjustment strap is aligned with the outside of the
handle. See figure 5.
11. Assemble the grip onto the end of the height adjust-
ment handle as shown in figure 5.
12. Place the 5/16" tooth-lock washer between the height
adjustment handle and the height adjustment strap.
Insert the 5/16" x 3/4" carriage bolt through the handle,
the tooth-lock washer and the strap. Assemble the 5/16"
Std. Wrt. washer and the plastic knob onto the end of the
bolt and tighten. See figure 6.
5/16" x 1-5/8"
CURVED
HEAD BOLT
BOWED
WASHER
5/16" LOCK
WASHER
1/4" HEX NUT5/16" HEX NUT
GRIP
HEIGHT
ADJUSTMENT
HANDLE
HEIGHT
ADJUSTMENT
TUBE
5/16" x 3/4"
CARRIAGE BOLT
5/16" TOOTH
LOCK WASHER
KNOB
5/16" FLAT
WASHER
(STD. WRT.)
HEIGHT
ADJUSTMENT
HANDLE
HEIGHT
ADJUSTMENT
STRAP

7
FIGURE 9
1/4" HEX LOCK NUT1/4" HEX LOCK NUT
1/4" x 1" CURVED HEAD BOLT
FIGURE 11
LOWER HOPPER TUBE
HOPPER BAG
BOTTOM
UPPER
HOPPER
TUBE
3/8 " HEX LOCK NUT
(OUTSIDE)
3/8" x 3/4" HEX BOLT
(INSIDE)
FIGURE 8
UPPER H
O
PPER TUBE
S
2. Slide the two upper hopper tubes together and line up
the center holes as shown in figure 8.
Right Left
BAG FLAP
UPPER HOPPER TUBE
(LEFT HAND SHOWN)
END HERE
CENTER CUT OUT
(START HERE)
3. Fasten the upper hopper tubes together using a 1/4"
x 1" curved head bolt and a 1/4" hex lock nut.
Tighten. See figure 9.
1/4" x 1"
CURVED HEAD BOLT
LOWER
HOPPER
TUBE
1/4 " HEX LOCK NUT
FIGURE 10
ASSEMBLY OF HOPPER BAG
1. Insert the left hand upper hopper tube through
the stitched flaps of the hopper bag, starting at
the center cut out in the top of the bag. See
figures 7, 8 and 9. Repeat for the right hand
upper hopper tube.
FIGURE 7
4. Assemble the two lower hopper tubes together using
a 1/4" x 1" curved head bolt and a 1/4" hex lock nut.
Tighten. See figure 10.
5. Place the assembled lower hopper tubes into the
bottom of the hopper bag as shown in figure 11.
6. Assemble the ends of the upper and lower hopper
tubes together using two 3/8" x 3/4" hex bolts (on the
inside) and two 3/8" hex lock nuts (on the outside).
Tighten to allow bag to pivot freely. See figure 11.

8
FIGURE 14
IMPORTANT: Do not over bend the support rods
during the following step. Over bending will cause the
spring steel rods to loose supporting tension.
10. Assemble the two hopper support rods as shown in
figure 15. Place end of rod into hole in upper hopper
tube and bend rod just enough to fit bottom end of rod
into hole in bottom hopper tube.
8. Assemble the frame strap to the lower hopper tube
using two 1/4" x 1-1/4" hex bolts and 1/4" hex lock
nuts. See figure 13.
7. Assemble the bag retainer and the bag frame strap to
the front edge of the bag bottom. Place the bag
retainer on top and the bag frame strap underneath
the bag bottom. Fasten retainer and strap together
using six #10 x 5/8" slotted screws and #10-32 hex
lock nuts. See figure 12.
#10-32 HE
X
LOCK NUT
FRAME STRAP
FRONT EDGE OF BAG BOTTOM
#10-32 x 5/8" SCREW
BAG RETAINER
FIGURE 12
FIGURE 13
1/4" x 1-1/4" HEX BOLT
(OUTSIDE)
LOWER
HOPPER
TUBE
1/4" HEX
LOCK NUT
FRAME STRAP
9. Secure the bag corners over the lower hopper tube
by snapping the flap to the bag bottom on both sides.
See figure 14.

SNAP
FLAP
SUPPORT RODS
FIGURE 15
11. Locate (by touch) the hole in each upper hopper tube.
Pierce holes through the stitched bag flaps, aligned
with the located holes in both hopper tubes. See
figure 16.
UPPER HOPPER TUBE
FIGURE 16

9
FIGURE 18
FIGURE 17
12. Slide the hopper bag pivot rod through the side of an
upper hopper tube where the hole was pierced.
Assemble a mounting clamp, two bag arms and
another mounting clamp onto the rod as shown in
figure 17. Push the rod on through the other upper
hopper tube on the opposite side of the bag.
13. Assemble the two remaining hopper mount clamps
onto the pivot rod on the outside of the bag. Fasten
them to the inside clamps using four 5/16" x 3/4" hex
bolts and 5/16" hex lock nuts. Tighten securely. See
figure 18.
14. sing a hammer, lightly tap a palnut onto each end
of the pivot rod. See figure 18.
HINT: To ease assembly of the palnuts, place the bag
on its side on a hard surface. With the bottom end of
the pivot rod against the surface, tap a palnut onto
the top end of the rod. Repeat for other end of rod.
15. Secure the rope to the top center of the hopper bag
frame as shown in figure 19.
FIGURE 21
17. To assemble the hopper bag to the sweeper, slide
the ends of the bag arms into the ends of the hitch
tubes and secure with two 3/8" x 3/4" clevis pins and
3/32" hairpin cotters. See figure 21.
FIGURE 19
3/32" HAIRPIN
COTTER
HITCH TUBE
HITCH TUBE
BAG ARM
3/8" x 3/4"
CLEVIS PIN
UPPER
HOPPER
TUBE
WIND SCREEN
SNAP
LOOP
16. Assemble the wind screen to the hopper bag frame
by snapping the screen's four corners loops around
the frame's upper hopper tubes. See figure 20.
FIGURE 20
MOUNTING CLAMP
BAG ARM
PIVOT ROD
USE THIS HOLEUSE THIS HOLE
5/16" x 3/4"
HEX BOLT
5/16" HEX
LOCK NUT
PALNUT
MOUNTING
CLAMP
(OUTSIDE)

10
ATTACHING SWEEPER HITCH TO TRACTOR
1. Place the tractor and sweeper on a flat level surface.
2. Set the sweeper height adjustment handle to about
the middle of its adjustment range.
3. Attach the sweeper hitch to the tractor hitch, arrang-
ing the 3/4" spacers into one of the six possible
combinations shown in GRO P A and GRO P B
diagrams below.
IMPORTANT: To obtain the best performance from your
sweeper, arrange the spacers so that the sweeper bag is
approximately level with the ground and approximately
5" to 7" off the ground as shown in figure 22.
GROUP "B" - For vehicles with hitches
having 10" to 13" ground clearance.
GROUP "A" - For vehicles with hitches
having 8" to 10" ground clearance.
BLACK LINE IS TRACTOR HITCH
HITCH BRACKET MOUNTED
BELOW HITCH TUBES
BLACK LINE IS TRACTOR HITCH
HITCH BRACKET MOUNTED
ABOVE HITCH TUBES
FIGURE 22
APPROXIMATELY LEVEL
(5" to 7" FROM SURFACE)
BRUSH HEIGHT ADJUSTED
APPROXIMATELY MID-WAY

11
KNOW YOUR SWEEPER
HOW TO USE YOUR SWEEPER
BRUSH HEIGHT ADJUSTMENT
To adjust your sweeper brushes to the best operat-
ing height, loosen the adjustment knob and push
down on the height adjustment lever to raise the
brush. See figure 22. Best adjustment is when the
brush setting is 1/2" down into the grass. Always
mow the grass to an even height before sweeping.
SWEEPING SPEED
Try a starting speed of approximately 3 m.p.h. (third
gear on most tractors). Depending on the conditions,
it may be necessary to adjust the sweeping speed in
order to achieve best results.
CAUTION: Keep sweeper away from fire. Ex-
cessive heat can damage the brushes and
hopper bag and could cause the bag and its
contents to burn.
CAUTION: Never attach the hopper rope to any
part of your body or clothing! Never hold onto
the rope while towing the sweeper! Attach the
rope to the towing vehicle to keep it away from
wheels and rotating parts.
DUMPING OF SWEEPER
Your sweeper can be dumped easily without getting
off of the rider or tractor. Simply pull the rope forward
to dump the hopper. Always empty hopper after each
use.
OPERATION
Hopper Bag Collects grass clippings, leaves and debris.
Hopper Rope Permits dumping of hopper bag from the drivers seat.
Windscreen Helps prevent collected material from being blown out of hopper bag.
Bag Arms Connects the hopper bag to the sweeper housing.
Pivot Rod Allows hopper bag to tilt forward to dump material.
Height Adjustment Handle Adjusts the operating height of the sweeper.
Height Adjustment Strap Holds the height adjustment handle in position when locked.
Knob Locks the height adjustment handle to the height adjustment strap.
Hitch Bracket Connects the sweeper to the towing vehicle. Adjusts for various height tractor hitches.
HOPPER BAG
WINDSCREEN
BAG ARM
PIVOT ROD HEIGHT
ADJUSTMENT
HANDLE
KNOB
HITCH
BRACKETS
HEIGHT
ADJUSTMENT
STRAP
HEIGHT
ADJUSTMENT
STRAP
HOPPER
ROPE

12
MAINTENANCE SCHED LE
Fill in dates as you
complete regular service.
Check for loose fasteners X
Check for worn or damaged parts X X
Lubricate brush shaft bearings X
Lubricate wheel bearings X
Clean Sweeper X X
Clean/Lubricate gears X
Before each use
After each use
Twice a year
Every season
Before storage
Every two years
Service Dates
CUSTOMER RESPONSIBILITIES
Read and follow the maintenance schedule and the
procedures listed in the maintenance section.
SCHEDULED MAINTENANCE
1. Clean the sweeper after each use.
Inspect for worn or damaged parts, such as brushes
and wheels.
2. Lubricate the brush shaft bearing twice a year with a
few drops of light weight oil. See figure 23.
FIGURE 23
CLEANING
1. Clean sweeper housing with a soft brush or cloth.
2. Clean debris from hopper bag with a brush or broom.
3. Remove any material which has wrapped around
brushes or ends of brush shaft.
FIGURE 24
HEX BOLT FLAT WASHER
FLAT WASHER
HEX LOCK NUT
HUB CAP
SPACER
HEIGHT ADJUSTMENT SLOT
HEX BOLT
OIL BEARINGS HERE
FLAT WASHER
MAINTENANCE
1. Clean the sweeper and hopper bag thoroughly to help
prevent rust and mildew.
2. To collapse the hopper bag for storage, remove the two
hopper support rods from the rear of the hopper.
3. Store in a dry area.
CAUTION: Before storing the sweeper,
always empty the hopper bag to avoid
spontaneous combustion.
STORAGE
3. Every two years, remove the wheels and clean the
gears found inside the wheel housing. After cleaning,
lubricate with an even coat of light grease. To remove
the wheel, pop off the hub cap using a screwdriver
and remove the lock nut and flat washer. See figure
24.

13
WHEEL GEAR AND PAWL SERVICE
IMPORTANT: Do not remove both wheels at the same
time to avoid mixing of parts. (The R.H. and L.H. ratchet
gears are not interchangeable.) Make notes on the posi-
tion of washers and snap rings during disassembly.
1. Remove one wheel from the sweeper.
2. Remove the retaining rings and washers which hold the
ratchet gear onto the brush shaft.
3. Remove the gear by sliding it off the brush shaft. (Look
for the drive pin, which may fall out of the brush shaft
when the ratchet gear is removed.) See figure 26.
4. To reassemble, insert the drive pin through the hole
near the end of the brush shaft. Make sure the pin slides
back and forth easily in the shaft.
5. Lightly grease the shaft and fill the ratchet gear with
grease. Assemble the ratchet gear back onto the shaft.
6. Lightly grease the axle and the wheel's gear teeth and
then reassemble the wheel. The brushes should rotate
only during forward rotation of the wheel. If the brushes
are driven (rotated) by both forward and reverse rota-
tion of the wheel, the drive pin is jamming in the ratchet
gear. Disassemble to clean and lubricate the drive pin
and the ratchet gear.
BRUSH REPLACEMENT
NOTE: Brush replacement should be done one brush at
a time.
1. Remove the hopper bag from the sweeper.
2. Loosen the hex bolts and lock nuts on two single
brush retainers which clamp one brush to the double
brush retainers. Do Not loosen or remove the bolts
which fasten the double brush retainers to the brush
shaft. See figure 25.
3. Slide the brush out of the retainers, noting on which
side of the brush the bristles overlap. See figure 25.
4. Install new brush, making sure the bristles overlap on
the same side of the brush as before. See figure 25.
BRUSH ROTATION
BRUSH ROTATION
OVERLAP
BRISTLES
OVERLAP
BRISTLES
SINGLE
BRUSH
RETAINERS
DOUBLE BRUSH RETAINER
BRUSH
SHAFT
1. Brushes set too low.
2. Brushes are jammed
3. Wheels are jammed.
Wheels skid when sweeping. 1. Adjust height till brushes are 1/2"
down into grass.
2. Stop sweeper. Remove obstruction.
3. Remove one wheel at a time to check
for obstruction or damage. Refer to
Service and Adjustments section.
FIGURE 25
SERVICE AND ADJUSTMENTS
TROUBLESHOOTING
RATCHET
GEAR
DRIVE
PIN
FIGURE 26

14
REPAIR PARTS FOR MODEL 45-0290 - 38" LAWNSWEEPER
A
C
1AA
B
B
CD
3
4
5
6
7
7
7
8
9
10
11
12
13
14
15
15
15
15
16
16
17
18 19
20
21
22
23
23
23
23
24 25
26
26
27
28
29
29
29
29
30 31
32
33
33
35 36 37
38
39 41
42
43
43
44
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
60
61
64
63
62
65
66
67
68
69
70
71
72
73
74
75
75
76
77
77
78
79
80
81
82
83
85
86
34 34
87
45
78
23
D
2
58
88
84

15
REPAIR PARTS LIST FOR MODEL 45-0290 - 38" LAWNSWEEPER
PARTS
Ref. Part Qty. Description
No. No.
1 47370 1 Hitch Tube, R.H.
2 47371 1 Hitch Tube, L.H.
3 24182 1 End Plate, R.H.
4 24183 1 End Plate, L.H.
5 24485 1 Wrapper
6 43175 2 Bolt, Hex 1/4-20 x 1/2" Lg.
7 C-9M5732 26 Rivet, Pop
8 23854 1 Brace, Rear Support
9 43673 1 Skirt, 38"
10 24486 1 Retainer, Skirt
11 23336 2 Washer, Special
12 63869 1 Height Adjustment Tube Ass'y.
13 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg.
14 44695 2 Washer, Bowed 1" x .32" x .06"
15 43086 12 Lock Washer, 5/16"
16 43083 6 Nut, Hex 5/16-18 Thread
17 R19212113 2 Washer, 5/8" SAE
18 1629-56 2 Retainer, Dust Cover
19 44910 2 Bushing, Brush Shaft
20 24085 1 Brush Shaft
21 47488 4 Brush, 38"
22 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg.
23 43013 18 Nut, Hex Lock 1/4-20 Thread
24 23580 4 Retainer, Brush (Double)
25 23581 8 Retainer, Brush (Single)
26 44008 2 Washer, Flat 1-1/8" x .78" x .025"
27 47046 2 Dowel Pin (Drive)
28 44692 4 Bolt, Hex 5/16-18 x 1/2" Lg.
29 43064 12 Nut, Hex Lock 5/16-18 Thread
30 44911 2 Spacer, .39 I.D". x 1-1/4" O.D. x .5"
31 44006 2 Washer, Flat .849" x .598" x .025"
32 46219 2 Spacer, .78 I.D". x 1-1/4" O.D. x .5"
33 1650-21 4 Ring, Retaining .594"
34 44007 6 Washer, Shim 1-1/8" x .594" x .025"
35 141 4 Washer, Flat 1-1/2" x .375" x .062"
36 1038 2 Nut, Hex Lock 3/8-24 Thread
37 2674-32 2 Hub Cap
38 44961 2 Bolt, Hex 3/8-24 x 3-1/4" Lg.
39 23400 2 Bushing, Spacer
40 2692-6 1 Gear, Pinion R.H. (not shown)
41 2692-7 1 Gear, Pinion L.H.
42 43661 4 Bolt, Hex 1/4-20 x 1" Lg.
43 63027 2 Ass'y, Dust Cover
44 44968 1 Tube, pper Hopper (R.H.)
Ref. Part Qty. Description
No. No.
45 44969 1 Tube, pper Hopper (L.H.)
46 43968 1 Tube, Lower Hopper (R.H.)
47 43969 1 Tube, Lower Hopper (L.H.)
48 44971 1 Hopper Bag
49 43687 1 Wind Screen
50 23352 1 Strap, Bag Frame
51 43926 2 Rod, Hopper Support
52 43737 1 Hopper Rope
53 24190 1 Retainer, Bag
54 24191 1 Strap, Height Adjustment
55 23687 1 Bracket, Hitch
56 24192 1 Bracket, Hitch (Straight)
57 24193 1 Handle, Height Adjustment
58 24487 2 Bag Arm
59 47373 1 Rod, Hopper Bag Pivot
60 44985 2 Wheel & Tire Ass'y. (with bearings)
61 45088 4 Wheel Bearing
62 46782 2 Bolt, Hex 5/16-18 x 3" Lg.
63 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg.
64 43063 2 Bolt, Hex 5/16-18 x 1" Lg.
65 46847 1 Bushing, Spacer
66 R19111116 2 Washer, Flat 5/16" x 11/32" x 11/16"
67 43720 1 Knob, Wing 5/16-18 Thread
68 43080 1 Bolt, Carriage 5/16-18 x 3/4" Lg.
69 43081 1 Washer, Flat 5/16" Std. Wrt.
70 43943 1 Grip, Height Adjust
71 44732 1 Washer, Tooth Lock 5/16"
72 23353 1 Pin, Hitch
73 23368 2 Tube, Hitch Spacer
74 43343 1 Hairpin Cotter, 1/8" #4
75 23331 4 Clamp, Hopper Mount
76 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg.
77 44917 2 Palnut, 3/8"
78 43978 2 Bolt, Cvd. Hd. 1/4-20 x 1" Lg.
79 1509-90 2 Bolt, Hex 1/4-20 x 1-1/4" Lg.
80 43346 6 Bolt, Sl. Tr. Hd. #10-32 x 5/8" Lg.
81 43662 6 Nut, Hex Lock #10-32 SEMS
82 43407 2 Bolt, Hex 3/8-16 x 3/4" Lg.
83 43082 2 Nut, Hex Lock 3/8-16 Thread
84 1540-31 2 Washer, Flat .78" x 1.25" x .06"
85 43055 2 Hairpin Cotter, 3/32" #3
86 44044 2 Pin, Clevis 3/8" x 3/4" Lg.
87 43070 2 Washer, 3/8" Std. Wrt.
88 43084 2 Bolt, Hex 5/16-18 x 1-3/4" Lg.
47548 1 Owners Manual

16
REPAIR PARTS
303 West Raymond
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com