ahn myLab SM-02 User manual

AHN myLab SM-02
Analog Magnetic Stirrer without heating 10L
Instruction Manual

1. PRODUCT DESCRIPTION
4. FEATURES & SPECIFICATIONS
• Powerful DC motor delivers constant speed under varying load condions.
• Variable speed seng from 400 to 2200 RPM with infinite mode of run me.
• Small footprint saving valuable bench space.
This manual provides important safety information for the magnetic stirrer. It should
be kept near the equipment for quick & easy reference. This instrument helps in
mixing liquids upto 10L (H₂O) volume.
2. INTENDED USE
This magnetic stirrer is ideal for Mixing, stirring, titrations, preparing solution for
respective uasage etc.
3. STANDARD ACCESSORIES
NOTE: Before using the instrument, please read this user manual carefully. This user manual is
intended to assist with the operation and care of the unit only and not its repair. For repair
please contact the supplier.
1
• Power Adaptor: 100-240VAC, 50/60Hz (Input), 12V 1.5A (Output).
• Product user manual & Warranty card.
• Magnec sr bar (25mm).
DC Motor
400 to 2200 RPM
Motor Type
Speed Range
Permissible Ambient Temp. 5 °C to 40 °C
< 80%
IP 42
Permissible Relative Moisture
Weight
Protection class
Power Consumption
Input Voltage
230 x 150 x 78 mm
Dimensions
10 L
Max Stirring capacity (H₂O)
Maximum recommended bar size
2200 RPM
1800 RPM
1500 RPM
1000 RPM
Maximum Speed
25mm
35mm
50mm
60mm
1.5 kg
Continuous Operation
Time Mode
12V 1.5A
5.5W

5. INSTALLATION
This product is warranted to be free from defects in material and workmanship for a
period of two (2) years from date of purchase. Your product will be duly repaired upon
prompt notification in compliance with the following conditions :
The warranty is invalidated by any non-factory modification, which will immediately
terminate all liabilities on us for the products or damages caused by its use. The
customer shall be responsible for the product or use of products as well as any
supervision required for safety. If requested the products must be returned to the
distributor in well packed and insured manner and all shipping charges must be paid.
NOTE: Some states do not allow limitation on the length of implied warrantiesor the exclusion
or limitation of incidental or consequential damages. This warranty gives you specific legal
rights. This warranty is given expressly in lieu of all other warranties, expressed or implied.
6. OPERATION
SWITCH ON THE DEVICE
Aer connecng the power adapter at the back side of the device as shown in picture
below, switch ON the main power supply & turn the knob towards right unl “a click”
sound heard.
START / STOP OPERATION
Once all the pre-requisites procedure are done. To START the operaon, switch on
the main power supply & turn the knob towards right unl “a click” sound heard
which means the srrer is ready to set speed. Speed gradually can be increased from
400 RPM to 2200 RPM by turning the knob from le to right & to decrease the speed
turn the knob from right to le. This equipment runs on connuous mode (for infinite
me).
Gently remove the upper packaging and take out the stirrer by holding it from the
bottom. When this equipment is used for the first time, ensure that all the packaging
accessories are removed from the product. Please keep all the packaging in safe
storage for at least 2 years for warranty purposes.
7. WARRANTY STATEMENT
Power Socket
SS Top plate
Knob
Stirring
LED
2

8. PRODUCT DISPOSAL
In case the product is to be disposed of, the relevant legal regulations are to be
observed.
Information on the disposal of electrical and electronic devices in the European
Community.
The disposal of electrical devices is regulated within the European Community by
national regulations based on EU Directive 2012/19/EU on waste electrical and
electronic equipment (WEEE). According to these regulations, any devices supplied
after 13.06.05 in the business to business sphere, to which this product is assigned,
may no longer be disposed off in municipal or domestic waste. They are marked with
the following symbol to indicate this.
As disposal regulations within the EU may vary from country to country,
please contact your supplier if necessary.
The purchaser agrees that there is no warranty of merchant-ability or of fitness for any
intended purpose and there are no other remedies or warranties, implied, which
extend beyond the description on the face of the agreement. This warranty is only
applicable to the original purchaser.
Product received without proper authorization will not be processed for warranty or
service. All items returned for service should be sent with postage prepaid in the
original packaging or other suitable packaging, padded to avoid damage. We will not
be responsible for damage incurred by improper packaging.
NOTE: This warranty is valid only if the warranty is registered with the supplier within 30 days
from the date of purchase.
0345-00-0000-02-003-R0
7. WARRANTY STATEMENT
For you reference, make a note of serial number, date of purchase and supplier
here.
Serial No.: Purchase Date:
Supplier:
© 2020 AHN Biotechnologie GmbH
®
AHN Biotechnologie GmbH
Uthleber Weg 14
D-99734 Nordhausen
Germany
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.ahn-bio.de