Ahrend Fount User manual

Fount Installation Manual
This manual will help you build the perfect solution for
a comfortable workstation.
* The manual shows installation of the quattro version.
* All legs can refer to this manual but the Original leg has
been taken as an example to explain.

page 2
Fount Installation Manual
1
2Install middle leg (Single and DUO version without middle leg, please omit this step)
Structure
Plastic bracket
(16 pcs)
Quick fix
(16 pcs)
Middle leg
(1 pcs)
Beam
(8 pcs)
M8 x 55
ISO 7380
screws
(32 pcs)
M8 nuts
(32 pcs)
End leg
(2 pcs)
T30
M6 x 10
ISO 7380
(8 pcs)
(16 pcs for Wired)
Wired is the only different middle leg from others
(16 pcs of the screw)

page 3
Fount Installation Manual
3Insert plastic Quick fix element
4The beams are attached into the adapter by screws and nuts of M8
Assemble and fix the end legs
M8 x 55
ISO 7380
T40
(16 pcs for DUO version)
(8 pcs for Single version)
Sliding top option

page 4
Fount Installation Manual
5Assemble the middle leg(s) but not yet fully fix the screws
M8 nuts reversed Flange of
the nut not in the U-profile
T40
6Wood steel leg has different way to connect with the frame and leg
Only for wood steel leg,
For all other legs go to
point 10 on page 6.
Beam
(2 pcs)
Wood steel leg
(2 pcs)
Plastic bracket
(4 pcs)
Quick fix
(4 pcs)
pre-installed
Quick fix sliding top option
(4 pcs)
pre-installed
M8 x 55
ISO 7380
(16 pcs for DUO version)
(8 pcs for Single version)

page 5
Fount Installation Manual
8
Wood steel leg installation
Install the other side
7
8
Slide tube over bracket while holding movable Alu-part upwards
Push both tubes on both brackets simultaneously
Only for wood steel leg
Only for wood steel leg

page 6
Fount Installation Manual
Fix the table beam
9
10 Insert plastic bracket
Only for wood steel leg
T40
M8 x 30
ISO 7380
(4 pcs)

page 7
Fount Installation Manual
Insert the cable clips (optional)
11
10 Install the cable tray (optional)
12
Bracket
(2 pcs)
Plastic hook
(4 pcs)
Cable tray
(1 pcs)

page 8
Fount Installation Manual
13
Fix the cable tray to the table beams
Fix the bracket to the table beams
Hang the cable tray on the bracket
14
Assemble the cable tray and the bracket
Insert plastic hook into the hole of cable tray and then turn 90°
Insert plastic hook into the hole of bracket and then turn 90°
1
1
2
2
M6 x 16
DIN 7500C
(2 pcs)
T40

page 9
Fount Installation Manual
15
10
16
Install the screen (optional)
Screen holder
(2 pcs)
Fabric screen
(1 pcs)
Fix the screen holder to the
table beams.
Screen holder brackets are
alligned to the U brackets
(from the legs).
Fix the screen to the table beams
M6 x 16
DIN 7500C
(2 pcs)
T40
Insert the screen into the screen holder.

page 10
Fount Installation Manual
17
18
Find the correct pre-drilled holes of the tabletops, install the screws for Quick fix
For sliding top follow
the steps from point
19 to point 24 on page 11
Connect the tabletops to the frame structure by Quick fix
Quick fix screws are mounted into the pre-drilled holes in
the desk top and then putted into the quick fix. Than locked.
Locked
Quick fix screw
T20