aidapt VR110T Manual

VR110T
Width Adjustable Bath Board with Turntable
Fixing and Maintenance Instructions
This le is available to view and download as a PDF at
www.aidapt.co.uk. Sight impaired customers can use a free
PDF Reader (such as adobe.com/reader) to zoom in and
increase the text size for improved readability.

INTRODUCTION
Thank you for purchasing the Width Adjustable Bath Board from Aidapt.
Please examine your product for any visible damage before using/installing. If you see any
damage or suspect a fault, please do not use, but contact your supplier.
For maximum strength and safety, this plastic bath board is made from a single piece
mould and is supplied with a handle. The contoured design provides added comfort and
the well-spaced drainage holes ensure the water drains away quickly and eciently. The
Easy Self-Locating Fixing System makes adjustment, positioning and removal simple and
safe.
If desired, you may purchase a green handle.
FITTING YOUR BATH
BOARD
Before attempting to t your
bath board please check
that you have the following
parts:
NB. If any parts are
missing or damaged
please contact your
supplier.
INTENDED USE
The Adjustable Bath Board is an aid to help accommodate users whilst bathing.
N.B. This equipment must be installed by a competent person and a risk
assessment may be needed as to the suitability of the stool for the
particular user.
Weight Limit: 180 kg (28 st.)
NB. Do not exceed the weight limit stated – doing so could put the user at risk.

ATTACHING THE HANDLE
1. Insert the two ends of the blue
handle into the circular holes
at one end of the bath board.
Insert the handle, which is slightly
curved to one side, so that the top
of the handle leans in, towards the
middle of the bath board.
2. Using the plastic handle xing
screws supplied, insert each in
turn into the corresponding hole
on the bottom of the bath board
and, holding the handle on
the top of the bath board, turn
the plastic xing screws until they
are nger tight only. NB. Do not
use a screwdriver as this may
damage the screws, if required a
large coin may be used carefully
to assist with turning the screws.
ATTACHING AND ADJUSTING THE FEET
1. Turn the bath board over so that the
bottom of the board is facing upwards.
2. Insert each foot into the slot on the
underside of the bath seat.
3. Turn the bath board over so that you can
see the top of the board and locate the
four corresponding slots for each foot.
4. Insert a plastic xing screw through
the slots into the narrow opening at the
top of each foot and, holding the foot to
prevent it from turning, turn the xing
screw until it is nger tight only. NB. Do
not use a screwdriver as this may
damage the screws, if required a large
coin may be used carefully to assist with
turning the screws.
5. Repeat for all four feet

ATTACHING AND ADJUSTING THE FEET CONTINUED
6. Place the blue swivel disc into the hole in the middle of the bathboard. Whilst holding in
place, use the circular bolt to secure in place from the bottom. Ensure you tighten until
it is secured in place, but can still rotate. Do not over tighten, as the disc will not swivel.
FITTING AND ADJUSTING THE BATH BOARD
1. Turn the board over with the feet facing up.
2. Loosen o the feet holding the plastic xing screw in position.
3. Turn the board over so that the feet are facing down.
4. Place the board over the bath traversing its width.
5. Reach underneath the board and push both sets of feet outwards evenly until they are
gripping the wall of the bath.
6. Tighten o the plastic xing screws. N.B. It is only necessary to tighten the xing screws
nger tight.
7. Do not over tighten them as this can cause damage to the thread and cause the
product to fail.
8. Double check the feet are friction tight to the wall of the bath before use.
Always check the tightness of the board before each use
Always repeat the installation every time the board is removed

a) a temperature of 90°C for 1 minute
b) a temperature of 85°C for 3 minutes
c) a temperature of 80°C for 10 minutes
CLEANING
The Bath Board should be cleaned using a non-abrasive cleaner or mild detergent with a
soft cloth only. Abrasive cleaners e.g. AJAX and/ or abrasive cleaning pads may seriously
damage the product beyond repair and should not be used. Always ensure that you wipe
dry the equipment.
If to be disinfected by heat, one of the following three temperatures and duration of
exposition can be used:
MAINTENANCE
Please check the cradle periodically for any signs of damage and if in doubt contact your
supplier.
REISSUE
If you reissue or are about to reissue this product, please thoroughly check all components
for their safety. This includes tightness of all nuts/bolts/castors and other screw in/bolt in/
push in components.
If in any doubt, please do not issue or use, but immediately contact your supplier for service
support.
TECHNICAL INFORMATION
Width ..........................................................................................................................................................757mm
Depth..........................................................................................................................................................350mm
Height........................................................................................................................................................... 95mm
Maximum User Weight Limit............................................................................................28 stone (180kg)
Width Adjustment.........................................................................................................................463-680mm
Net Weight ..................................................................................................................................................2.38kg
Expected Lifetime ................................................................................................................................... 3 Years
IMPORTANT INFORMATION
The information given in this instruction booklet must not be taken as forming part of or
establishing any contractual or other commitment by Aidapt Bathrooms Limited or its
agents or its subsidiaries and no warranty or representation concerning the information is
given.
Please exercise common sense and do not take any unnecessary risks when using this
product; as the user you must accept liability for safety when using the product.
A copy of the instructions leaet can be downloaded from our website.
Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX
Telephone: [phone] • Fax: [phone]
Web: www.aidapt.com • Email: [email protected].uk