Airflow 7006A User manual

MaxAir Wall
Exhaust Fan
7006A
7008A
Installation Instructions

Check proposed location of fan will not foul
joists, existing wiring or other internal wall
features (wall thickness between 110mm and
310mm). Use template provided to mark out
hole. Cut a hole through the wall Ø180mm.
Screw fan assembly to wall via four corner
openings, see Fig A. (Appropriate fasteners to
be used for each installation - not provided).
1.
Remove termination cover, see Fig B. (Screws
marked with 1, 2, 3).
2.
Electrician to make electrical connection as
shown, using three core, 1mm2cable. Replace
termination cover.
3.
With fan assembly mounted on the internal wall,
cut PVC sheet to suit the wall depth.
Green/Yellow
Green/Yellow
4.
Screws
marked
with 1, 2, 3,
retain the
terminal
cover
to the
chassis.
Fig. B
Fig. A
7006A Connection Diagram
External
isolating
switch
External
isolating
switch
Auto switch (internal)
Pull-cord switch
7008A Connection Diagram
Fan
assembly
7006A & 7008A MaxAir Wall Exhaust Fan Installation Instructions
© Clipsal Australia Pty Ltd

Coil the cut PVC sheet around wall grille outlet
spigot and slide into retaining clips.
5.
Screw wall grille outlet to external wall.
(Appropriate fasteners to be used for each
installation - not provided).
6.
Place cover assembly as shown. Tighten
retaining screw. Test. Ready to go.
7.
IMPORTANT NOTE:
7006A - Automatic Model
Before replacing the outer cover, ensure unit has
been “off” for five minutes, then return shutter
lever to its lowest position.
7008A - Pull Cord Model
Before replacing the outer cover, ensure the
shutter lever is in its lowest position. (ie. pull
cord = OFF)
7006A - Shutter Operation
Approximately 60 seconds delay on opening and
up to three minutes delay on closing of shutters,
ensuring silent operation.
WARNING:
This appliance is not intended for use by young
children or infirm persons, unless they have
been adequately supervised by a responsible
person to ensure that they can use the appliance
safely, and to ensure that they do not play with
the appliance.
Instructions to suit model no. 7006A and 7008A.
Appliance intended for installation through
external walls only.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons, in order to avoid a hazard.
Optional
sticky tape
Retaining
clip
Cover
assembly
Fan
assembly
Retainer
screw
Wall
grille
outlet
Sheet to be
approx. 20mm
overlapping
duct
Fan
assembly
INTERNAL EXTERNAL
Wall grille
outlet
© Clipsal Australia Pty Ltd
7006A & 7008A MaxAir Wall Exhaust Fan Installation Instructions

F1771/01 CLIPCOM19000
Clipsal Australia Pty Ltd reserves the right to change specifications,
modify designs and discontinue items without incurring obligation
and whilst every effort is made to ensure that descriptions,
specifications and other information in this catalogue are correct, no
warranty is given in respect thereof and the company shall not be
liable for any error therein.
© Clipsal Australia Pty Ltd.The identified trademarks and copyrights
are the property of Clipsal Australia Pty Ltd unless otherwise noted.
Product of Clipsal Australia Pty Ltd
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
clipsal.com
Warranty
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the
product which the consumer has under the Trade Practices Act and similar State and Territory Laws.
The original purchaser of this Airflow Wall Exhaust Fan is provided with the following warranty, subject
to the following conditions. Clipsal Australia Pty Ltd warrant this product for a period of three years
from the date of purchase, for all parts defective in workmanship or materials. All defective parts will be
replaced free of charge. The following exclusions do not preclude the purchaser from those statutory
rights consumers have under the Trade Practices Act or similar State and Territory Laws.
Warranty Conditions
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified or changed in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person and must be
connected to the voltage requirements as specified in the ratings label.
4. The manufacturer does not accept liability for any direct or consequential damage, loss or other
expense arising from misuse or incorrect installation and operation of the appliance.
5. Warranty will only be given on appliances where proof of purchase date is provided eg. original
invoice or copy.
As a record of your purchase, please fill out the following details and file this information with your
purchase invoice.
Airflow Model Number: ______________________________________________________________
Serial Number: ____________________________________________________________________
Purchased From: ___________________________________________________________________
Date of Purchase: __________________________________________________________________
For Service
Please contact the installer if service is required for this product. If the installer is not known contact
Clipsal National Customer Service on the following numbers:
Tel 1300 2025 25
Fax 1300 2025 56