Airflow MaxAir 7105A User manual

MaxAir Window
Exhaust Fan
7105A Auto-Switched
7107A Pull-Cord Switched
Installation Instructions

Remove termination cover, see Fig. A. (Screws
marked with 1, 2, 3.)
Fig. A
5.
Cable (3 core flex) to be placed as shown in
Fig. B. Electrician to make electrical connections
(3 core 1mm2flex, Ø7mm [17/64”] specified) as
shown in Fig. C. Stripped ends to be kept to a
minimum. Replace termination cover.
Fig. B
Using template, cut hole in glass ø230 ± 2mm.
Slide internal clamp over your arm as shown.
Fold external clamp and insert through the hole
in the window pane.
Make sure the seal of external clamp is against
the glass, then align and insert the bolts through
internal clamp. Brass nuts supplied should then
be connected to bolts and finger tightened only.
If required, apply liquid or similar soap to foam
seal on inside of external clamp. Carefully
slide cylindrical window grille outlet end of
fan assembly through opening. With screws
provided, attach fan assembly to window clamp
assembly (4 places).
1.
4.
2.
3.
Fan
assembly
Apply soap to
the foam seal
Internal
clamp
External
clamp
Finger
tighten
only
Screws
marked 1,
2, 3, retain
the terminal
cover to the
chassis.
Break tab for
cable access
7105A Auto Switched & 7107A Pull-Cord Switched MaxAir Window Exhaust Fan Installation Instructions
© Clipsal Australia Pty Ltd

WARNING:
The appliance is not intended for use by children
or infirm persons without supervision.
Children should be supervised to ensure they do
not play with the appliance.
Appliance intended to be mounted on external
window only.
NOTE: SHUTTER OPERATION
Do not turn auto-switched models on without
the front cover fitted. Auto-Switched fans are
fitted with a thermal actuator, thus requiring
approximately three minutes to fully open and
approximately 60 seconds to close shutters.
Pull-cord models are operated either by the built
in pull-cord and/or separate switch (thermal
actuator). If it is decided to use and operate fan
via a separate switch, the delay on opening and
closing of shutters must also be noted.
Fig. C
7105A Connection Diagram
7107A Connection Diagram
6.
Place cover assembly as shown, over fan
assembly and tighten retaining screw. Test.
Ready to go.
HOLE CUT-OUT TEMPLATE
HOLE CENTRE
Ø230mm
External
isolating
switch
External
isolating
switch
Pull-cord
switch
Cover
assembly
Retaining
screw
© Clipsal Australia Pty Ltd
7105A Auto Switched & 7107A Pull-Cord Switched MaxAir Window Exhaust Fan Installation Instructions

Warranty
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the
product which the consumer has under the Trade Practices Act and similar State and territory laws.
The original purchaser of this Airflow Window Exhaust Fan is provided with the following warranty,
subject to the following conditions. Clipsal Australia Pty Ltd warrant this product for a period of three
years from the date of purchase for all parts defective in workmanship or materials. All defective parts
will be replaced free of charge. The following exclusions do not preclude the purchaser from those
statutory rights consumers have under the Trade Practices Act or similar State and Territory Laws.
Warranty Conditions
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified or changed in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person and must be
connected to the voltage requirements as specified in the ratings label.
4. The manufacturer does not accept liability for any direct or consequential damage, loss or other
expense arising from misuse or incorrect installation and operation of the appliance.
5. Warranty will only be given on appliances where proof of purchase date is provided eg. original
invoice or copy.
As a record of your purchase, please fill out the following details and file this information with your
purchase invoice.
Airflow Model Number: ______________________________________________________________
Serial Number: ____________________________________________________________________
Purchased From: ___________________________________________________________________
Date of Purchase: __________________________________________________________________
For Service
Please contact the installer if service is required for this product. If the installer is not known contact
Clipsal National Customer Service on the following numbers:
Tel 1300 2025 25
Fax 1300 2025 56
F1697/03
CLIPCOM18999
Clipsal Australia Pty Ltd reserves the right to change specifications,
modify designs and discontinue items without incurring obligation
and whilst every effort is made to ensure that descriptions,
specifications and other information in this catalogue are correct, no
warranty is given in respect thereof and the company shall not be
liable for any error therein.
© Clipsal Australia Pty Ltd. The identified trademarks and copyrights
are the property of Clipsal Australia Pty Ltd unless otherwise noted.
Product of Clipsal Australia Pty Ltd
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
clipsal.com