Airflow SunShine 6600ATP User manual

Important: All electrical work must be carried out by
a licensed electrician or similarly qualified person and
installed in accordance with Australian Standard AS
3000 and all building regulations. This product
requires a 230/240 Volt, 50Hz electrical supply.
Supplied with this unit are Clipsal labelled fan, heat
and light mechanisms.
WIRING DETAILS
1. Install any extra wiring that is required.
2. Click the switch mechanisms into the switch-
plate (not supplied) in order of preference.
3. Connect the wiring to the switches as shown
in the electrical diagram below.
4. Remove the Sunshine's electrical terminal
cover and wire according to the label adjacent
to the terminal strip.
ELECTRICIANS’ WIRING INSTRUCTIONS
Once the wires are connected, incoming
cable must not be fouled by the cover.
Remove cut out portion as required and
replace.
5. Clean the cowling and globes with a soft,
moist cloth. Check that the power is switched
on, then check all switch operations.
HEATHEAT
HEATHEAT
HEAT
LIGHTLIGHT
LIGHTLIGHT
LIGHT
FANFAN
FANFAN
FAN
ACTIVEACTIVE
ACTIVEACTIVE
ACTIVE
NEUTRALNEUTRAL
NEUTRALNEUTRAL
NEUTRAL
EARTHEARTH
EARTHEARTH
EARTH
Product of Gerard Industries Pty Ltd ABN 27 007 873 529
Head Office 12 Park Terrace, Bowden, SA 5007
Telephone [phone] Facsimile [phone]
E-mail [email protected]
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the
product which the consumer has under the Trade Practices Act and similar State and Territory Laws.
The original purchaser of this Sunshine Radiant Heater is provided with the following warranty, subject to
the following conditions. Gerard Industries Pty Ltd warrants this product for a period of 5 years from the
date of purchase for all parts defective in workmanship or materials. All defective parts will be replaced
free of charge. The following exclusions do not preclude the purchaser from those statutory right
consumers have under the Trade Practices Act or similar State and Territory Laws.
WARRANTY CONDITIONS
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified or changed in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person and must be
connected to the voltage requirements as specified in the ratings label.
4. Heat globes supplied with this unit are covered by a separate 2 year replacement warranty and are
excluded from the 5 year warranty. Incandescent globes are excluded from all of the above
warranties.
5. The manufacturer does not accept liability for any direct or consequential damage, loss or other
expense arising from misuse or incorrect installation and operation of the appliance.
6. Warranty will only be given on appliances where proof of purchase date is provided eg. original
invoice or copy.
For your future reference, please complete the following details and file this information with
your purchase invoice.
Sunshine Model 6600ATP.
Serial Number
Purchased From
Date of Purchase
NATIONAL SERVICE CENTRES
NSW/ACT Southside Elements
752 Old Princes Highway
Sutherland 2232
Phone [phone]
VIC/TAS W.A.M. (Wiring & Maintenance)
1126 Whitehorse Road
Box Hill 3128
Phone [phone]
QLD Universal Electrical
9 Horizon Drive
Beenleigh 4102
Phone [phone]
SA Ivesons Electrical
417 South Road
Keswick 5035
Phone [phone]
WA Electrical Spares & Service
Unit 2/12 Buckingham Drive
Wangara 6052
Phone [phone]
NT G & T Electrical Enterprises Pty Ltd
4 Iris Street
Alawa 0810
Phone (Mobile) 018 895 239
or 018 892 043
WARRANTY
New Zealand
Clipsal Industries (NZ) Ltd (Auckland)
Telephone [phone] Facsimile [phone]
E-mail [email protected]
Customer Service
Free Fax [phone]
Auckland/Mobile Phone [phone]
Free Phone (0508) CLIPSAL
2547725
© Copyright Gerard Industries Pty Ltd 2001

IMPORTANT
THIS CARD IS ALSO YOUR
INSTALLATION TEMPLATE
FITTING INSTRUCTIONS
Thank you for purchasing this quality
Sunshine Radiant Globe Heater. The
Sunshine Range is made in Australia for
Australian homes and includes a 5 year in
home warranty with a 2 year replacement
warranty on the heat globes.
Before attempting to install this unit, please
read the following instructions carefully.
Installing your Sunshine Heater according to
these directions will ensure years of trouble-
free operation.
This unit can be mounted in any room that
requires direct, radiant heat at the flick of a
switch. These instructions suit Model Number:
6600ATP En Suite Radiant Heater, Light and
Exhaust Fan
SUITABLE LOCATIONS
To achieve the most effective heating from
the Sunshine's infra-red radiant heat globes,
the unit must be positioned directly over the
area requiring warmth.
Sunshine heaters are designed for cavity
type ceilings. Flat roof installation in NOT
recommended unless an additional flue is
installed to exhaust outside.
Before you start fitting the unit, make sure
your ceiling has at least 280mm clearance
from the roof. This unit must not be mounted
in areas that are subject to direct splashing.
The Sunshine En Suite must be mounted in
the horizontal position only and is not
suitable for 'cathedral' or 'raked' ceilings.
MOUNTING
1. Using this card in its open state as a template, position it on the area of the ceiling where you
want to install your Sunshine. Draw around the edges of the template with a pencil to mark
the hole cutting size. Be sure to check above the ceiling for minimum space of 280mm
and the location of the ceiling joists.
2. Using a saw, cut out the section along the drawn lines.
3. Insert your Sunshine into the hole, making sure to pull the two side springs inwards so that
the body can pass through the hole without damaging the plaster. Once fully inserted, the
springs must be returned to their original position. The body is now securely fixed in the
ceiling.
Note: Springs can be adjusted to suit either 10mm or 13mm plasterboard ceilings.
Alternatively, the unit can be fixed into position via the four holes in the body flange.
4. The lamp surround has been designed to position heat globes correctly in the main body.
Clip the ceiling cowl to the body, making sure all four clips snap into place. Failure to position
lamp surround correctly may cause heat globes to touch the main body and cause warping.
5. Screw the two R63 60 watt (small) light globes into place. Screw the two large heat globes
through the cowl holes and into the body mounted sockets. The globes should be screwed in
firmly, but not over tightened, to ensure a good electrical contact.
CLEANING
•Remove heat globes when at room temperature. Wipe with a damp cloth, never immerse.
•Unclip ceiling cowl and wash in warm soapy water. Always use a soft cloth, never abrasives.
•Clean away any excess fluff from inside the body, motor/blade brackets.
SPARE PARTS
Electrical switches are available from any electrical
wholesaler. The central light globes (small) should be
replaced by pearl R63 60 watt lamps, Part No. 6630-LP.
The special Hard Glass radiant heat globes are only
available from selected retailers and wholesalers,
Part No. 6500C.
Note: Maximum wattage of small centre globes is
60 watts.
F1671/01
11
11
122
22
233
33
344
44
455
55
5