Airlink101 AWLC6070 User manual

150N Draft 802.11n Wireless Cardbus Adapter
Model # AWLC6070
User’s Manual
Rev. 1.0

2
Table of Contents
1. Introduction .................................................................................................................3
1.1 Package Contents .................................................................................................3
1.2 Features ................................................................................................................3
2. Installation...................................................................................................................4
3. Configuring the Adapter ............................................................................................13
4. Wireless Monitor........................................................................................................18
4.1 Wireless Information............................................................................................18
4.2 AP List.................................................................................................................19
4.3 Profile Settings.....................................................................................................20
4.4 Configuring Encryption ........................................................................................22
4.5 Ad-hoc and Peer-to-Peer Wireless Networks ......................................................28
4.6 About...................................................................................................................31
Appendix A – Features..................................................................................................32
Appendix B – Information..............................................................................................33
Technical Support .........................................................................................................35

3
1. Introduction
Congratulations on your purchase of the 150N Draft 802.11n Wireless Cardbus Adapter.
The 150N Cardbus Adapter provides wireless data rate of up to 300 Mbps* downlink
and 150Mbps* uplink when used with other AirLink101® 150N or 300N wireless
products. The high bandwidth combined with extended wireless coverage delivers fast
and reliable connection for all of your networking applications.
A full range of security features such as WEP, WPA-PSK, and WPA2-PSK provide the
highest level of wireless network security. The bundled Wireless Utility allows you to set
up the adapter with an easy-to-use user interface. Best of all the 150N Cardbus Adapter
works with 802.11g and 802.11b network devices ensuring compatibility with your
existing wireless products.
1.1 Package Contents
Before you begin the installation, please check the items of your package. The package
should include the following items:
•Wireless Cardbus Adapter
•Quick Installation Guide
•Installation CD (Driver/Utility/Manual)
1.2 Features
•Industry’s highest wireless standard with IEEE 802.11n draft specification 2.0.
•64-bit/128-bit WEP encryption, Pre-shared Key (PSK), and Wi-Fi Protected
Access (WPA2) and WPA support provide full protection for your wireless
connection
•Higher data rate increases the reliability and stability of wireless connections
•Great for environments with higher wireless data traffic requirements
•Fully backward-compatible with 802.11b/g devices
•Works best with other AirLink101® 150N and 300N wireless products

4
2. Installation
This section provides instructions on how to install the 150N Draft 802.11n Wireless
Cardbus Adapter. The driver is installed along with the utility.
Step 1 Insert the Cardbus adapter into an available Cardbus slot and turn on your
computer.
Step 2 After turning on the computer, Windows will launch the Found New Hardware
Wizard. The Found New Hardware Wizard appears differently depending on your
operating system. Click Cancel to quit the wizard and insert the Installation CD into your
CD drive.
Step 3 The Autorun screen will pop up. Select Install Utility and Driver from the menu.

5
Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white
screen, go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your
CD drive) and click OK.
Windows Vista users: At this point, you may get a warning message like the one
below. Make sure that you click Allow to continue with the installation.

6
Step 4 Click Next at the welcome screen.

7
Step 5 Click Next to accept the default destination folder.

8
Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click
Yes at the Digital Signature Not Found prompt).
For Windows Vista, click the Install this driver software anyway button when the
security warning appears.

9
Step 7 Click Yes, I want to restart my computer now and then Finish to restart your
computer.
Step 8 After the computer is restarted, Windows will ask to connect to Windows
Update, select No, not this time and click Next. If this screen does not appear, you can
skip to section 2.2.

10
Step 9 Select Install the software automatically and click Next.

11
Step 10 Click Continue Anyway at the Windows Logo Screen.
(For Windows 2000, click Yes at the Digital Signature Not Found prompt).
For Windows Vista, click the Install this driver software anyway button when the
security warning appears.

12
Step 11 Click Finish.

13
3. Configuring the Adapter
This section describes how to connect your wireless adapter to a wireless network.
Note to Windows XP Users:
You must disable the Wireless Zero Configuration Utility in order to use the bundled
Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Windows
Vista users can skip the following instructions and go to Step 1
Double-click on the Wireless Network Connection Icon in the system tray and then
click on Properties or Advanced.
When the new wireless network connection properties window appears, go to the
Wireless Networks tab, uncheck the “Use Windows to configure my wireless
network settings” check box and click OK.

14
Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray
at the bottom right-hand corner of your screen.
Step 2 Go to the AP List tab, select the SSID (Network Name) of the wireless network
you wish to connect to, and click Connect.

15
If the network you are attempting to connect to is configured for encryption, you will see
an orange lock icon next to the network.

16
When you click on it and click connect, a box will pop up requesting the wireless
encryption key for the router. Enter the encryption key into the box and click OK.

17
Step 3 You should now be connected. You should see “Connected” in the top, right
hand corner, and there will be a blue circle around the antenna icon next to the network
name.
Troubleshooting:If you are experiencing problems with the connection (unable to
connect, low signal strength, slow connection speed, not working, unstable wireless
connection) you will want to tune your router’s signal by changing channels on the
router.
You do not need to change the channel on the card, it will automatically pick up the new
channel after you reboot. The only channel that you need to change is the router’s
channel.
Your router has 11 different channels to choose from. Start with channel 1 and work
your way up. Each time you change the channel on the router, make sure that you
restart the wireless computer before trying to connect again. Keep going through the
channels until you find one that gives you a stable connection.
For instructions on changing channels, refer to the documentation that came with your
router.

18
4. Wireless Monitor
This section describes the various functions of the Wireless Monitor that you can
configure, including the settings of wireless encryption.
4.1 Wireless Information
The Wireless Information box at the top of the window provides you with the status of
the current connection, including signal, network name (SSID), IP Address and router
channel.

19
4.2 AP List
The AP List tab displays all the available wireless networks detected by the Wireless
Adapter. Simply select the wireless network you wish to connect to and click Connect.
If you have created multiple profiles, you can use the profile chooser at the bottom to
select the specific profile you want to use. Then click Activate to enable that profile.

20
4.3 Profile Settings
This section provides instructions on using the Profile Settings section of the wireless
monitor.
The My Wireless Networks box lists the different profiles you’ve created for the
different networks that you use. Profiles are automatically created and added to this list
when you connect to new networks. You can also manually add profiles.
To modify an existing profile, select that profile from the My Wireless Networks box
and click on modify.
To create a new profile, click on New.