Airlink101 AGSW808POE User manual

Quick Installation Guide
8-Port 10/100/1000Mbps Switch
with 8-Port PoE
Model# AGSW808POE
Ver. 1A

1
Power Over Ethernet (PoE) is an evolving technology designed to
simultaneously deliver power and transmit data through an Ethernet
cable. Modeling after the technology used in telecommunication
systems which supplies power to telephones, PoE powers network
device without the need of AC electrical outlets. By eliminating the
power cords and the power infrastructure, the technology greatly
simplifies the wiring and deployment matters and brings lots of
convenience and benefits in home, office, and industrial
environments.
Features
•8 x 10/100/1000Mbps Auto-negotiation Fast Ethernet RJ45
with 8-Port PoE function
•Compliant with IEEE802.3af specification
•Support PoE Power Maximum 15.4W per PoE port
•Support PoE Powered Device (PD) classification
•Over-Current and Short-circuit Protection
•Each port supports auto MDI/MDIX, no need to use cross-over
cables or an up-link port
•Flow control fully supported:
- Half-duplex: backpressure flow control
- Full-duplex: IEEE802.3x flow control
•Provide non-blocking wire speed reception and transmission
•Embedded SDRAM for packet storage
•1024-entry look-up table direct mapping mode
•Embedded 16-entry CAM for hash collision mapping
•Optional maximum packet length 1536/1522 Bytes
Purpose
This Quick Installation Guide tells you how to install your Switch and
how to connect it to your Ethernet network.
Terms/Usage
In this manual, the term “Switch” (first letter upper case) refers to your
8-Port 10/100/1000Mbps Switch with 8-Port PoE, and “switch” (first
letter lower case) refers to other Ethernet switches.
1. Introduction

2
1.1 Package Contents
•1 x AGSW808POE
•1 x Switching Power Adapter
•1 x Quick Installation Guide
•4 x Rubber foot for shock cushioning
1.2 Panel
1.2.1 Front Panel
The picture below depicts the front panel of the PoE Switch:
Figure 1-1 Front Panel view of the Switch
•PoE Ports (Port 1~8)
These ports are 802.3af PoE enabled ports, the PoE port will
automatically activate when a compatible terminal is identified. The
PoE switch will distribute power through the Ethernet ports to the
connected PoE device. For devices that are not compatible, the
PoE port will not supply the power to this device. This feature
allows users to freely and safely utilize the 802.3af PoE for Power
over LAN devices on the network. These ports support network
speeds of 10Mbps, 100Mbps and 1000Mbps, and can operate in half
and full-duplex transfer modes. These ports also support automatic
MDI/MDIX crossover detection, which give the PoE switch “plug and
play” capabilities. Just simply connect RJ45 network cable
between the PoE switch and the device and it will automatically
detect the settings of the device and adjust itself accordingly

3
•LED Indicators
Comprehensive LED indicators display the status of the switch and
the network (see Section 1.2.3).
1.2.2 Rear Panel
Figure 1-2 Rear Panel view of the Switch
•Power Adapter Connector: DC 48V/1.5A, AC 100~240V,
50~60Hz
•DC Terminal: used for connection to auxiliary backup DC power,
DC 48V/1.5A
1.2.3 LED indicators information
The front panel LEDs provide instant status feedback for help with
monitoring and troubleshooting when needed.
•Power: Power Indicator
Status
LED Color Solid Blinking Off
Power Green
The Switch is
power-on N/A No power

4
•PoE 1~8 LEDs
Status
LED Color Solid Off
PoE 1~8 Green
PoE devices
connected
successfully
PoE port failed,
possibly due to:
power shortage, over
the power adapter
output current
•LAN 1~8 LEDs
Status
LED Color Solid Blinking Off
LAN
1~8
100TX
Green
Connected to
100M
network
Transmitting/
Receiving data
on 100M
network
Connected to
10M network or
no device is
connected
LAN
1~8
1000TX
Green
Connected to
1000M
network
Transmitting/
Receiving data
on 1000M
network
Connected to
10M network or
no device is
connected

5
1.3 Technical Specifications
Standards
•IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX and IEEE
802.3af (PoE)
Ports
•8 x 10/100/1000Mbps Auto-Negotiation RJ45 Port with 8 PoE ports
Access Method
•CSMA/CD
Transmission Method
•Store and Forward
Topology
•Star
SRAM Buffers
•Embedded SRAM for packet storage
•1024-entry look-up table in direct mapping mode
•Embedded 16-entry CAM for hash collision mapping
Jumbo Frame
•Optional maximum packet length of 1536/1522 bytes
Data Transfer Rate*
•Ethernet: 10/20Mbps – Half/Full-Duplex
•Fast Ethernet: 100/200Mbps – Half/Full Duplex
•Giga Ethernet: 1000/2000Mbps – Half/Full Duplex
PoE Budget
•Up to 15.4W max. per PoE port
PoE Power on RJ45
•Pin 1, 2,3, 6
Dimensions
•146(W) x 84.1(D) x 42(H) mm
Power Consumption
•6.3 watts. (max. no PD device connected)
•64 watts (max. with 12.95W PoE device connected)
Physical and Environmental
•Power Adapter: 48V DC / 1.5A, 100~240V AC, 50~60Hz
•Operation Temperature: 0 °C ~ 50°C
•Storage Temperature: -10°C ~ 70°C

6
•Humidity: 5% ~ 90% RH, non-condensing
The site where you place the switch may greatly affect its performance.
When installing, take the following into your consideration.
2.1 Installation
The setup of the switch can be performed using the following steps:
•Visually inspect the DC jack and make sure that is fully secured
to the power adapter
•Make sure that there is proper heat dissipation and adequate
ventilation around the Switch. Do not place heavy objects on the
Switch.
2.2 Desktop or Shelf Installation
When installing the Switch on the desktop or shelf, please attach the
rubber feet to the Switch. Peel off the protective paper on the pads and
attach them on the bottom of the Switch (one at each corner).
2. Installing the Switch

7
This section describes how to connect the Switch to your network.
3.1 Connection
The Switch supports 8 10/100/1000Mbps Ethernet ports and all of
the 8 ports are PoE enabled ports. These PoE ports will
automatically activate when a compatible terminal is identified. The
Switch will supply power through the Ethernet port to the connected
PoE powered device (PD). For legacy devices that are not
compatible, the PoE port will not offer power to this device. This
feature allows users to freely and safely mix legacy and PoE devices
on their network.
The Switch supports 10Mbps Ethernet, 100Mbps Fast Ethernet and
1000Mbps Giga Ethernet; and it runs both in half and full duplex
mode using two pair of Category 5 cable. These RJ45 ports are
Auto-MDI type port. The Switch can auto negotiate the MDI-II or
MDI-X type, so you can connect any RJ45 cable regardless if it is a
standard or crossover cable.
3. Connecting the Switch

8
E-mail: [email protected]
Web Site: www.airlink101.com
*Network conditions and environmental factors as well as network overhead lower
actual data throughput rate. Specifications are subject to change without notice.
Photo of product may not reflect actual content. Copyright © 2011 AirLink101®. All
rights reserved. AirLink101®, the stylized AirLink101® logo, specific product
designations, and all other words and logos that are identified as trademarks
and/or service marks are, unless noted otherwise, the trademarks and service
marks of AirLink101®. All other product or service names are the property of their
respective holders. AirLink101® products are protected under numerous U.S. and
foreign patents and pending applications, mask work rights, and copyrights.
Technical Support