Airlinkplus AWLC3025 User manual

Ver. 1A
Quick Installation Guide
PackageContent:
•802.11g Cardbus Adapter
•Driver& Utility CD
•Quick Installation Guide
1
Model # AWLC3025
Step 1 Before installing the utility software, do not insert the cardbus adapter into
your computer. If the cardbus is inserted already, Windows will detect the adapter
and request for a driver. Click Cancel to quit the wizard and remove the cardbus
adapter from your computer.
Step 2 Close all programs that are currently running. Insert the provided Utility
and Driver CD into your CD drive and select Install Driver & Utility from the setup
menu.
Step 3 When the welcome screen appears, click Next.
Section 1
Install Utility Software
Step 4 Click Next to accept the default destination folder to install the software or
click Browse to manually select a different destination folder.
Note: If the setup menu does not appear automatically, click Start, Run, type D:
\Setup.exe (where Dis the letter of your CD drive) and click OK.

Continue on back...
Step 6 Remove the Driver & Utility CD from your CD drive and then click OK to
restart your computer.
Step 1 After the computer is restarted, insert the cardbus adapter into the
computer.
Section 2
Install Cardbus and Driver
Step 2 Select Install the software automatically and click Next.
Step 5 Click Next at the Select Program Folder screen.
Continueon Back
Note: In most cases, Windows will automatically install the driver after the
computer is restarted. If the Found New Hardware Wizard appears, follow the
instructions below. The Found New Hardware Wizard will look different depending
on your operating system. Follow the on-screen instructions to complete the
installation. For Windows 98SE and ME users, you may be prompted to insert the
Windows 98SE or ME CD during the driver installation. Be sure to have your
Windows 98SE or ME CD ready.

Section 3
Section 3
Configuring the Cardbus
Step 1 Uncheck the External Configuration box if it is checked and click
Apply.
Step 2 Highlight the network device you want to connect to from the device list
and click Connect.
Step 3 Verify that the Status field displays Connected to network and that the
card has signal quality and click OK to exit.
To open the Cardbus Utility, double-click on the Wireless LAN Utility Icon on the
desktop. Or go to Start, (All) Programs, WlanUtility, Wireless LAN Utility.Step 4 Restart the computer.
Step 3 For Windows XP, click Continue Anyway at the Windows Logo
Compatibility screen.
For Windows 2000, click Yes at the Digital Signature screen.
For Windows 98SE or ME, insert the Windows 98SE or ME CD if prompted to do
so and click OK.
Step 4 Click Finish. Restart the computer if you are prompted to do so.

E-mail: [email protected]
TollFree: 1-888-746-3238
Web Site: www.airlinkplus.com
Section 5
Technical Support
For more advanced features and additional details,
please refer to the User’s Manual on the provided CD.
Section 4
Troubleshooting
BIf you do not see your wireless router/access point in the device list, reset your
wireless router/access point and click on Rescan.
DIf the cardbus is connected to the network and has signal quality but cannot
access the Internet, verify that you are able to obtain an IP address from your
wireless router/accss point.
AIf the utility cannot be opened or it reports that the cardbus is not found,
uninstall the driver and utility and try installing again. You can also verify if the
driver is installed properly in the Device Manager. For instructions on how to
access the Device Manager, please refer to the User’s Manual on the provided
CD.
CIf you see a lock icon next to the network device you want to connect to, it
means that it has encryption enabled. Be sure to input the correct encryption key
in the Privacy tab. For more information on how to configure the encryption
settings, please refer to the User’s Manual on the provided CD.
For Windows 2000/XP
Step 1 Go to Start, Run, type cmd and click OK.
Step 2 At the command prompt, type ipconfig/release and press Enter.
Step 3 After the IP address is released, type ipconfig/renew and press
Enter. You should get an IP address like 192.168.x.y (where x and y are
unique numbers assigned by your wireless router/access point). If you
don’t get an IP address, reset the wirelss router/access point and then try
ipconfig/renew again.
For Windows 98SE/ME
Step 1 Go to Start, Run, type winipcfg and click OK.
Step 2 Select the cardbus from the drop-down menu and click Release.
Step 3 After the IP address is released, click Renew. You should get an
IP address like 192.168.x.y (where x and y are unique numbers assigned
by your wireless router/access point). If you don’t get an IP address,
reset the wirelss router/access point and then try Renew again.