Airpura F600 DLX Use and care manual

OPER ATING
&
FILTER REPLACEMENT
DIRECTIONS
F600
DLX

TO BEGIN USING YOUR
AIRPURA
Inspect the exterior of your Airpura to verify there is no damage from shipping.
If any damage is noted, please follow the instructions from the distributor returns
policy.
Wipe the unit with a damp cloth to remove any dust from packaging
Plug the unit into a regular grounded 110 volt outlet
Turn on the unit to MAX and allow it to run for a few minutes
Set the variable speed control to the level you wish
The most ecient way to use your Airpura for regular air quality maintenance
is to run it at a low speed 24 hours a day 7 days a week.
Maintain a humidity level of below 40% at all times in your home.
FILTER MAINTENANCE AND REPLACEMENT
Ensure regular maintenance/replacement of lters
The Prelter
Can be vacuumed from the exterior of the unit once a month or more often.
Should be replaced at least after 12 months of use
To vacuum the Prelter
Use the brush attachment on your vacuum cleaner
Vacuum slowly around the mesh surface of the lter chamber
IMPORTANT SAFETY NOTE
Please ensure air purier is turned OFF when plugging into a power source.
Failure to do so may result in motor potentially stalling and/or burning.
MinMax
Off
1
MinMax
Off
2
MinMax
Off
3

Poly Prelter 600 2-pack
12 months
Air puriers models and lter congurations
Technical specications
3067330 60950
HepaBarrier 600CT Filter
(95 % ecient @ 1 Microns)
12-16 months
26 lbs Impregnated Carbon Filter
(35/65 % Blend : Potassium
Permanganate (KMnO4),
Coconut Shell Carbon)
24 months
Odors, airborne chemical control
and VOC control
26 lbs super enhanced
impregnated activated Carbon
13"H x 13.25"OD x 7.5"ID
Particle removal
HepaBarrier
Carbon bed
3 in deep x 570 in2surface
Air Flow 560 cfm
More cfm than any other
home unit available
Prelter
570 in2x 1 in
Post particle lter
306 in2
Size
23 in x 15 in
Weight
49 lbs total
Watts
120 on high / 40 on low
Sound Level
28.1 db on low (at 6 feet)
62.3 db on high (560 cfm)
(Room Level 25.1)
ETL Certied
Conforms to CSA C22.2
no 113 ANSI / UL 507
Prelter
Alternates Cotton Prelter
TarBarrier Prelter

To close the lter chamber
Replace
the gasket
Position the
indentation in the cover
into the center of the
HEPA lter
Replace
the 4 screws
and tighten
Turn the Airpura
back on casters
Insert the tube
into the lter
chamber inside
the Prelter
Let the spiral
open to ll
the opening
Open the top of the
spiral to make a
slight funnel
Insert the
Carbon canister into
the funnel and hold it
straight
Position the
Prelter inside
the lter
chamber
Place a felt gasket at
the bottom of the
lter chamber
Unfold the lter slider
(Supplied with replacement
lters or on request
Part#6F 001)
Roll it
into a spiral
Let the canister
slide down
thelter slider
Pull the lter slider up
out of the cavity using
both hands and let the
canister slide to the
bottom of the cavity
Remove the lter
slider and fold it
for further use
Slide in the
Hepa lter
To open the lter chamber
Turn over
the Airpura
Remove the 4
retaining screws
Take off
the cover
Remove
the gasket