AirTies Air 4920 Operator's manual

INTERNET
YOUR MODEM
YOUR STB
1
2
12
3
4
12
SUCCESS
OUT OF RANGE

Designed by AirTies in Europe. Manufactured in China.
Wi-Fi Name: AirTies_Air4920_XXXX
Wi-Fi Password: abcdef1234
Designed by AirTies in Europe. Manufactured in China.
Wi-Fi Name: AirTies_Air4920_XXXX
Wi-Fi Password: abcdef1234
INTERNET
YOUR MODEM YOUR STB
1
WPS
2
WPS
YOUR STBADDITIONAL UNIT

SUCCESS
SUCCESS
SUCCESS

INTERNET
YOUR MODEM

LED
Indicators: Condition LED Color LED Behavior Timing State
Identifier Explanation Recommended Action(s)
Power OFF (OFF/Dark) - A
Power on device if desired. No other action required.
Power ON White Solid (No blinking) B
No action required. If unit was just powered on, then please wait for at least 2 minutes for the unit to complete its boot process.
Firmware upgrade in progress White Blinking
500ms OFF 500ms ON C
No action required. Please wait for the unit to reboot (and enter state B).
WLAN is active and the node has an active strong Mesh/Repeater connection on the 5GHz Radio. Green Blinking
50ms OFF 5000ms ON D
No action required.
WLAN is active and all MESH/Repeater links on 5GHz Radio are weak. Red Solid (No blinking) E
Bring device closer to another device on the MESH.
WLAN is active or Searching for radar activity (OFF/Dark) Both Radio LEDs are dark F
No action required.
WPS is in progress Green Blinking in sync with 2.4GHz led
WPS Cert. Compliant G
No action required.
WPS is succesful Green Solid (No blinking)
WPS Cert. Compliant H
This behavior is temporary and lasts for about 10 seconds, after which the LEDs
go to one of the following states: 1) MESH with strong signal (state D), and 2) MESH with poor signal (state E)
If LED is red (state E) then bring device closer to another device on the MESH. If LED is green (state D), then no action is required.
Unconfigured device. Green Blinking in sync with 2.4GHz led
4000ms OFF 4000ms ON I
Device has factory setting and is not connected to the home network in any
way (e.g., the device is not wired to the router-gateway)
Configure device (refer to Quick Installation Guide)
WLAN active, Device configured, No Repeater/MESH link on 5GHz Radio. Green Solid (No blinking) J
First AP (wired to router-gateway) No action required.
There is configured MESH/Repeater connection on 5GHz, however connection is inactive. (Cannot connect.) Red Blinking
1000msec OFF
1000msec ON K
AP is part of MESH, but unable to find any of its MESH partners.
Make sure other device(s) that are part of the MESH network are powered on and close enough to connect.
WPS is not successful Red Blinking with 2.4GHz led
WPS Cert. Compliant L
This behavior is temporary and lasts for about 10 seconds, after which the LEDs go back to the state the device was in before the WPS attempt
On failure, repeat WPS attempt after
bringing device next to another device that is already on the MESH network (i.e., in state D).
Power
5 GHz

This product makes use of software developed by the open source community.Any such software is licensed under the specific license terms applicable to that particular
software (like GPL, LGPL etc). Detailed information on the applicable licenses and license terms can be found on the device's user interface.
By using this product, you acknowledge that you have reviewed such license terms and that you agree to be bound by them. Where such terms entitle you to the source code
of said software, that source code will be made available at cost upon request from AirTies.
To obtain a copy of said source code, please send your request in writing via email to [email protected] or via snail mail to:
AirTies Wireless Communications
Gulbahar Mah. Avni Dilligil Sok. No:5
Celik Is Merkezi, Mecidiyeköy, 34394
ISTANBUL/Turkey
AirTies will mail to you a CD with the requested source code for $9,99 plus the cost of shipping. For details please contact [email protected]