Aiwa XK-009 User manual

AIWA-00391
S/M Code No.88-033 DATE OF ISSUE 6/1988-|
AIWA XK-009
SERVICE
MANUAL
e BASIC TAPE MECHANISM : a —6
STEREO CASSETTE DECK
@ TYPE. H, C, E, K, K1, Z
SPECIFICATIONS
Type
Track format
Power supply
Power
consumption
Frequency
response
Signal-to-noise
ratio
Wow and flutter
Tape speed
Recording system
Erase system
Motor
Stereo cassette tape deck
4 tracks, 2 channels
XK-O09E, Z
AC 220 V, 50/60 Hz
XK-009K, Ki
AC 240 V, 50/60 Hz
XK-009C
AC 120 V, 60 Hz
XK-009H
AC 120 V/220 V/240 V
switchable, 50/60 Hz
XK-009E, K, K1, Z,C
33 W
XK-009H
30 W
METAL tape: 20 — 22,000 Hz
CrO2 tape: 20 — 21,000 Hz
NORMAL tape: 20 — 20,000 Hz
95 dB (METAL tape dbx NR ON)
0.035% (According to DIN 45500)
0.018% (WRMS)}
4.8 cm/sec. (1-7/8 ips)
AC bias (frequency 105 kHz)
AC erase
System servomotor (for the
capstan) x 1
DC motor (for tape take-up during
playback/recording) x 1
DC motor (for F FWD/REW) x 1
AIWA Co., Lid.
Playback head
Recording head
Erase head
Inputs
Outputs
Dimensions
Weight
PC-OCC coil pure amorphous head
PC-OCC coil pure amorphous head
Double-gap sendust head
REC/LINE IN, CD/DAT DIRECT IN
maximum input sensitivity: 50 mV
(47 kQ)
PLAY/LINE OUT standard output
level: 530 mV (0 VU); suitable load
impedance: over 47 kf.
PHONES: 1.5 mW (8 0)
469 (W) x 136 (H) x 432.7 (D) mm
10.2 kg
@ Design and specifications are subject to change without
notice.
@ Noise reduction system manufactured under |icense from
Dolby Laboratories Licensing Corporation.
@ Dolby and the OO symbo! are trademarks of Dolby Labo-
ratories Licensing Corporation.
e@“dbx is a trademark owned and registered by dbx”
Tokyo Japan

DISASSEMBLY INSTRUCTIONS
1. Mechanism ASSY Removal
1) Remove side wooden panels R/L and the steel cabinet.
2) Remove 2 screws and take out the stabilizer solenoid.
(See Figure-1)
ROESIAP-YLIAK
Fig-1
3) Remove the cassette lid in the direction of arrow @s
Remove 6 screws and lay out the wires, then remove
the front cabinet in the direction of arrow @).
(See Figure~2)
D4¢AVE5REMS. JoyvhtreRryh
Pull out the wires. Front cabinet
LO
est
lid
4) Remove 5 screws and push button (EJECT), then pull
Fig-2
out the mechanism ASSY in the direction of the arrow,
Take care of the hook of the lever plunger ASSY at
this time. (See Figure-3)
AZAPFUYVIRILFULTTH6B
FAZSILTT.
Remove the spring and
then the screw.
Ts)
Tyan,
EJECT
Push-button,
EJECT
Fig~3
2. Cassette Holder Removal
1) Remove 2 screws in the EJECT state and then remove
the holder in the direction of the arrow. Be
carefull that the lever (EJECT) is also removed at
this time. (See Figure-4)
2) Turn on SW103 and SW107 to operate the mechanism in
this state.
LuN—, EJECT
Lever, EJECT
al
Fig~4
Ow
. Main-2 C.B Removal
1) Remove 4 screws and lift the main-2 circuit board.
(See Figure-5)
X4v-2 BH
Main-2 C.B
= —— y |
POYVKErKRyYh
Front cabinet
Fig-5
Wee ee ey
a9 Lever plunger Assy
race APUYZ, VN-
E-spring, Lever

ELECTRICAL MAIN
REF NO.
PART NO.
ae IG
87-001-384-010
82-226-645-010
87-020-111-010
87-020-877-010
82-100-630-01
87-020-533-01
87-020-679-01
87-027-895-01
87-001-383-01
87-020-619-01
87-027-909-01
87-001-387-01
oo00 oo0o°o
87-020-871-01
87-001-388-01
87-020-884-01
87-027-940-01
eoleaeke)
87-020-052-010
87-027-986-010
87-027-937-010
87-001-385-010
87-001-386-010
=== TRANSISTOR ===
82-371-625-010
89-109-521-010
89-110-155-010
89-210-154-510
89-309~-455-010
89-309-456-010
89-318-155-010
89-318-464-51
89-320-011-01
89-321-204-01
89-331-138-01
89-412-753-41
87-026-216-01
87-026~215-01
87-026-217-01
87-026-293-01
0
0
0
0
0
87-026-206-010
0
0
0
0
87-026-364-010
— = DIODE =
87-020-110-010
87-020-025-010
87-020-123-010
87-027-365-010
87-027-346-01
87-027-364-01
87-027-661-01
87-027-301-01
oo0o°o
87-027-416-010
87-027-702-010
87-027-399-010
PARTS LIST
DESCRIPTION
C,CX20188
1C,HD614042S-A87
C,L78M05
C,LC4966
C,LC6502B-724
C,M4069UBP
C,M4572BP
C,M5218L
1C,M5220P
C,M5238L
C,M54523P
C,M5F78M10
C,M5F78M12L
C,MSF79M10
1C,M5F79M12L
1C,NJM2903S
1C,NJM4556S
1C,NJM4560S
IC, TC4030BP
1€, UPC1252H2
1C,UPC1253H2
FET, 2SK30
TRANSISTOR, 2SA952K
TRANSISTOR, 2SA1015 GR
TRANS! STOR, 2SB1015Y,G
TRANS | STOR, 2SC945L ,Q
TRANSISTOR, 2SC945L ,P
TRANS!STOR,2SC1815 GR
TRANS | STOR, 2SC1846R,S
TRANSISTOR, 2SC2001K
TRANSISTOR, 2SC2120Y
TRANSISTOR, 2SC3113B
TRANS | STOR, 2SD1275
TRANS | STOR, DTA124EF
TRANS | STOR, DTA124ES
TRANS | STOR, DTC114YS
TRANSISTOR, DTC124ES
TRANS | STOR ,DTC144WS
TRANSISTOR, RN1202
DIODE, 1SS177
DIODE, 2B4B41,LC-2
DIODE ,DS446
DIODE,S5277B
DIODE, ZENER HZ11A2L
DIODE, ZENER HZ12A3L
DIODE, ZENER HZ30-2L
DIODE, ZENER HZ3A1
DIODE, ZENER HZ3C2
DIODE, ZENER HZ6C2L
DIODE, ZENER HZ7A3L
=== MAIN-1 CIRCUIT BOARD SECTION ——=
PCB-A
C253
C254
C255
C256
C701
*
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-133-010
MAIN-1 CIRCUIT BOARD
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT BP 2.2-50V
REF .NO,
c702
C703
C707
C708
c709
c710
C713
C715
C716
C717
c719
c720
C721
C722
C723
C724
C725
C726
C733
C734
C741
C742
C743
C744
C747
C748
C751
C754
C755
C759
C760
C761
c777
C778
c779
C781
C782
C783
C784
C785
C786
C793
C794
C795
C796
C797
C798
C813
c814
C815
C816
C817
c909
C910
C935
C936
C939
C1002
©1004
€1005
C1008
C1010
J701
J702
PART NO.
*87-010-133-010
*87-010-697-010
*87-010~402-010
*87-010-402-010
*87-010-379-010
*87-010-379-010
*87-010-697-010
*87-018-034-010
*87-018-034-010
*87-010-404-010
*87-010-133-010
*87-010-133-010
*87-014-193-010
*87-014-193-010
*87-014~-193-010
*87-014-193-010
*87-014-161-010
*87-014-161-010
*87-010-132-010
*87-010-132-010
*87-010-132-010
*87-010-132-010
*87-014-115-010
*87-014-115-010
*87-010-404-010
*87-010-404-010
*87-014-079-010
*87-010-138-010
*87-010-132-010
*87-010-378-010
*87-010-112-010
*87-010-112-010
*87-010-402-010
*87-010-402-010
*87-010-112-010
*87-014-131-010
*87-014-131-010
*87-014-041-010
*87-014~-041-010
*87-014-049-010
*87-014-049-010
*87-010-379-010
*87-010-379-010
*87-010-374-010
*87-010-374-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-265-010
*87-010-265-010
*87-010-697-010
*87-010-697-010
*87-010-697-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-071-010
*87-010-071-010
*87-010-402-010
*87-010-071-010
*87-010-402-010
87-009-019-010
87-009-019-010
DESCRIPT|ON
CAP,ELECT BP 2.2-50V
CAP,ELECT AWD 220-16
CAP,ELECT 2.2-50 SME
CAP,ELECT 2.2-50 SME
CAP,ELECT 22-16V
CAP,ELECT 22-16V
CAP,ELECT AWD 220-16
CAP,CERA-SOL S 150P
CAP,CERA-SOL S 150P
CAP,ELECT 4.7-50 SME
CAP,ELECT BP 2,2-50V
CAP,ELECT BP 2.2-50V
CAP,PP 0.00226
CAP,PP 0.0022G
CAP,PP 0.0022G
CAP,PP 0.0022G
CAP,PP 0.0039-100V G
CAP,PP 0.0039-100V G
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP, PP 0.0056G
CAP,PP 0.00566
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,PP 8200P-100V J
CAP,ELECT BP 22-25
CAP,ELECT BP 1-50
CAP,ELECT 10-16
CAP,ELECT 100-16
CAP,ELECT 100-16
CAP,ELECT 2,2-50 SME
CAP,ELECT 2.2-50 SME
CAP,ELECT 100-16
CAP,PP 0.0018
CAP,PP 0.0018
CAP,PP 220P
CAP,PP 220P
CAP,PP 470P
CAP, PP 470P
CAP,ELECT 22-16V
CAP,ELECT 22-16V
CAP,ELECT 47-10V
CAP,ELECT 47-10V
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4,7-50 SME
CAP,ELECT 4,7-50 SME
CAP,ELECT 33-16 SME
CAP,ELECT 33-16 SME
CAP,ELECT AWD 220-16
CAP,ELECT AWD 220-16
CAP,ELECT AWD 220-16
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 1-50
CAP,ELECT 1-50
CAP,ELECT 2.2-50 SME
CAP,ELECT 1-50
CAP,ELECT 2,2-50 SME
PIN JACK 2P(REC/LINE IN)
PIN JACK 2P(REC/LINE IN)
Ee A ee a Ts AY

REFNO.
J703
J704
J705
J706
L701
L702
L703
L704
L705
L707
L708
L709
L710
L711
L712
L713
L714
L715
L716
A\ R767
Av R791
ZX R792
RY701
SFR703
SFR704
SFR705
SFR706
PART NO,
87-009-019-010
87-009-019-010
87-009-019-010
87-009-019-010
*82-226-641-010
*87-003-051-010
*82-226-642-010
*82-226-642-010
*87-003-051-010
*82-226-628-010
*82-226-628-010
*82-132-631-010
*82-132-631-010
*82-226-690-010
*82-226-690-010
*82-226-689-010
*82-226-689-010
*82-226-623-010
*82-226-623-010
87-029-089-010
87-029-082-010
87-029-082-010
87-045-270-010
*87-021-747-010
*87-021-747-010
*87-021-745-010
*87-021-745-010
SFR1001*87-021-745-010
SFR1002*87-021-745-010
SW702
SW703
SW704
82-226-625~010
82-226-625-010
82~-226-630-010
DESCRIPTION
PIN JACK 2P(CD/DAT DIRECT IN)
PIN JACK 2P(CD/DAT DIRECT IN)
PIN JACK 2P(PLAY/LINE OUT)
PIN JACK 2P(PLAY/LINE OUT)
COIL,BIAS 105K
COIL,CHOKE 470 UH
COIL,OSC 105K-HX
COIL,OSC 105K-HX
COIL,CHOKE 470 UH
COIL, TRAP 105K
COIL,TRAP 105K
COIL,4. 7MMH, J
COIL,4. 7MMH, J
COIL,2.7 MMH
COIL,2.7 MMH
COIL,2.2 MMH J
COIL,2.2 MMH J
FILTER ,MPX PC-OCC
FILTER ,MPX PC-OCC
RES, FUSIBLE 1/4W-4.7
RES,FUSIBLE 1/4W-100
RES,FUSIBLE 1/4W-100
RELAY G5A-297P
SFR 220K
SFR 220K
SFR 47KB
SFR 47KB
SFR 47KB
SFR 47KB
PUSH SW(CD/DAT DIRECT) -
PUSH SW(MPX)
PUSH SW(MONI TOR)
—— MAIN-2 CIRCUIT BOARD SECTION =="
PCB-B
C101
C102
C103
C104
C201
C202
C203
C204
C205
C206
C207
C208
C209
C210
C221
C222
C223
C224
C225
C226
C229
C231
C232
C235
C236
C241
C242
C243
C244
*
*87-014-119-010
*87-014-119-01
*82-226-688-01
*82-226-688-01
*87-018-034-01
*87-018-034-01
*87-010-133-01
*87-010-133-01
*87-014-193-01
*87-014- 193-01
*87-014-193-01
*87-014-193-01
*87-014-161-01
*87~-014-161-01
*87-010-132-01
*87-010-132-01
*87-010-132-01
*87-010-132-010
*87-014-115-010
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
*87-014-115-010
*87-010-404-010
*87-010-404-010
*87~-010-404-010
*87-018-115-010
*87-018-115-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
*87-010-404-010
MAIN-2 CIRCUIT BOARD
CAP,PP 0.027G
CAP,PP 0.027G
CAP,FILM GU-1-100V
CAP,FILM GU-1-100V
CAP,CERA-SOL S$ 150P
CAP,CERA-SOL S 150P
CAP,ELECT BP 2.2-50V
CAP,ELECT BP 2.2~50V
CAP,PP 0.00226
CAP ,PP 0.0022G
CAP, PP 0.0022G
CAP ,PP 0.00226
CAP,PP 0.0039-100V G
CAP,PP 0.0039-100V G
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP,ELECT BP 1-50
CAP,PP 0.0056G
CAP,PP 0.0056G
CAP,ELECT 4,7-50 SME
CAP,ELECT 4.7~50 SME
CAP,ELECT 4.7-50 SME
CAP,CERA~SOL SS 47P
CAP,CERA-SOL SS 47P
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
CAP,ELECT 4.7-50 SME
REF .NO.
c901
c902
L101
L102
R101
R102
R105
R106
R107
R108
R109
R110
RY702
PART NO.
*87-010-696-010
*87-010-696-010
*82-226-622-010
*82-226-622-010
*87-025-429-010
*87-025-429-010
*87-025-455-010
*87-025-455-010
*87-025-423-010
*87-025-423-010
*87-025-414-010
*87-025-414-010
87-045-270-010
SFR101 *87-021-745-010
SFR102 *87-021-745-010
DESCRIPT1ON
CAP,ELECT AWD 470-25
CAP,ELECT AWD 470-25
COIL,TRAP 105K,PC-OCC
COIL, TRAP 105K,PC-OCC
RES,MF 1/6W 47K
RES,MF 1/6W 47K
RES,MF 1/4W 110K
RES,MF 1/4W 110K
RES,MF 1/4W 4.7K
RES,MF 1/4W 4.7K
RES,MF 1/6W 56K
RES,MF 1/6W 56K
RELAY G5A-297P
SFR 47KB
SFR 47KB
——= CONTROL CIRCUIT BOARD SECTION ===
PCB-C
C101
C102
C103
C104
C105
C106
C107
C108
109
C111
C112
C113
AXC116
C117
C118
C119
C120
C121
C123
C124
C126
L101
*
*87-010-698-010
*87-010-410-010
*87-010-247-010
*87-010-394-010
*87-010-378-010
*87-010-263-010
*87-010-374-010
*87-010-237-010
*87-010-436-010
*87-010-393-010
*87-010-695-010
*87-010-695-010
*87-019-112-010
*87-018-131-010
*87-010-401-010
*87-010-378-010
*87-010~-378-010
*87-010-235-010
*87-010-265-010
*87-010-401-010
*87-018-131-010
*82- 196-649-010
SFR101 *87-021-737-010
A\sw108
87-036-015-010
CONTROL CIRCUIT BOARD
CAP,ELECT 4700-25 105°
CAP,ELECT 330-50 VX
CAP,ELECT 100-50 SME
CAP,ELECT 220-35 SME
CAP,ELECT 10-16
CAP,ELECT 100-10V
CAP,ELECT 47-10V
CAP,ELECT 1000-16 SME
CAP,ELECT 1000-35
CAP,ELECT 100-35 SME
CAP,ELECT AWD 2200-25
CAP,ELECT AWD 2200-25
SPARK KILLER 0.01 E
CAP,CERA-SOL SS 1000P
CAP,ELECT 1-50 SME
CAP,ELECT 10-16
CAP,ELECT 10-16
CAP,ELECT 470-16
CAP,ELECT 33-16
CAP,ELECT 1-50 SME
CAP,CERA-SOL SS 1000P
COIL,OSC LC6502C
SFR 470
SLIDE SW(POWER)
=== DISPLAY CIRCUIT BOARD SECTION ==>
PCB-D
C201
C202
C203
C204
FL201
SwW202
Sw203
SW204
SW205
SW206
SW207
SW208
X20
*
*87-018-112-010
*87-018-112-010
*87-010-079-010
*87-010-075-010
82-226-621-010
87-031-771-010
87-031-771-010
87~-031-771-010
87-031-771-010
82-226-626-010
82-226-626-010
82-226-626-010
*87-030-096-010
DISPLAY CIRCUIT BOARD
CAP,CERA-SOL SS 30P
CAP,CERA-SOL SS 30P
CAP,ELECT 100-6.3
CAP,ELECT H5 10-16
FL, CP5345AGR(PEAK/CAL-LEVEL METER)
TACT SW(PEAK HOLD RESET,AUTO)
TACT SW(PEAK HOLD RESET,MANUAL )
TACT SW(LINEAR COUNTER RESET )
TACT SW(MEMORY ON/OFF )
PUSH SW(DOLBY-NR B)
PUSH SW(DOLBY-NR C)
PUSH SW(DBX)
FILTER,CERAMIC 4MHZ
——— KEY SWITCH CIRCUIT BOARD SECTION ==>
PCB-E
0201
0202
D203
*
87-001-137-010
87-001-137-010
87-001-138-010
KEY SWITCH CIRCUIT BOARD
LED, SLP981C50( RECORD )
LED,SLP981C50(REC MUTE)
LED, SLP481C50( PAUSE )

REFNO.
D204
D205
Sw201
SW202
SW203
SW204
SW205
SW206
SW207
SW208
Sw209
PART NO.
87-001-122-010
87-001-137-010
87-031-771-010
87-031-771-010
87-031-771-010
87-031-771-010
87~031-771-010
87-031-771-010
87-031-771-010
82-226-648-010
82-226-647-010
DESCRIPTION
LED, SLP381C50( PLAY)
LED, SLP981C50(OPERATION STANDBY)
TACT SW(REWIND/REV!EW)
TACT SW(PLAY)
TACT
TACT
TACT
TACT
Sw(STOP)
sw(F .FWD/CUE)
Sw(PAUSE)
SwW(RECORD)
TACT SW(REC MUTE)
SLIDE SW(TIMER)
PUSH SW(MEMORY, STOP/REPLAY )
I= JACK CIRCUIT BOARD SECTION ——-
PCB-F
C801
C802
C805
C807
J801
VR703
I= REC
PCB-G
VR701
a2 CAL..
PCB-H
VR705
VR707
*
*87-010-071-010
*87-010-071-010
*87-010-112-010
*87-010-112-010
87-009-018-010
82-226-627-010
JACK CIRCUIT BOARD
CAP,ELECT 1-50
CAP,ELECT 1-50
CAP,ELECT 100-16
CAP,ELECT 100-16
JACK 6,3,HP-AU(PHONES )
VOLUME, 10KA(PHONE LEVEL)
VR CIRCUIT BOARD SECTION —--
*
82-226-624-010
REC VR CIRCUIT BOARD
VOLUME , 20KA(RECORD LEVEL)
VR CIRCUIT BOARD SECTION ===
*
82-226-644-010
82-226-643-010
CAL VR CIRCUIT BOARD
VOLUME, SOKB (CAL.-REC LEVEL)
VOLUME , 5KB(CAL.-BIAS)
=== SWITCH CIRCUIT BOARD SECTION ———
PCB-|
SW704
Sws01
*
82-226-629-010
82-226-646-010
=== DBX-1 CIRCUIT BOARD
PCB-J
C306
C308
C312
C319
C320
C321
C406
C408
C412
C419
C420
C42)
SFR319
SFR419
*
*87-014-040-010
*87-014-033-010
*87-014-045-010
*87-015-425-010
*87-010-378-010
*87-015-215-010
*87-014-040-010
*87-014-033-010
*87-014-045-010
*87-015-425-010
*87-010-378-010
*87-015-215-010
*87-021-867-010
*87-021-867-010
—— DBX-2 CIRCUIT BOARD
PCB-K
C508
C509
C512
C520
C521
C608
C609
C612
C620
C621
SFR519
*
*87-014-033-010
*87-014-033-010
*87-014-045-010
*87-010-378-010
*87-015-215-010
*87-014-033-010
*87-014-033-010
*87-014-045-010
*87-010-378-010
*87-015-215-010
*87-021-867-010
SWITCH CIRCUIT BOARD
ROTARY SW(REC EQ)
ROTARY SW(CALIBRATION)
SECTION ===
DBX-1 CIRCUIT BOARD
CAP,PP 200P
CAP,PP 100P
CAP,PP 330P
CAP,AL 1-25
CAP,ELECT 10-16
CAP, TANTALUM 10-25V
CAP,PP 200P
CAP,PP 100P
CAP,PP 330P
CAP,AL 1-25
CAP,ELECT 10-16
CAP, TANTALUM 10-25V
SFR 47K
SFR 47K
SECTION ===
DBX-2 CIRCUIT BOARD
CAP,PP 100P
CAP,PP 100P
CAP,PP 330P
CAP,ELECT 10-16
CAP, TANTALUM 10-25V
CAP,PP 100P
CAP,PP 100P
CAP,PP 330P
CAP,ELECT 10-16
CAP, TANTALUM 10-25V
SFR 47K
REF.NO. PART NO. DESCRIPTION
SFR619 *87-021-867-010 SFR 47K
IID REMOTE CIRCUIT BOARD SECTION ———
(K1 MODEL ONLY}
REMOTE CIRCUIT BOARD
SOCKET,DIN 8P( REMOTE )
PCB-L ‘i
J1 87-032-985-010
a= MECHANISM-1 CIRCUIT BOARD SECTION ==
PCB-M - MECHAN!SM-1 CIRCUIT BOARD
SwW104 = 81-505-607-010 LEAF SW(MT DET. )
SW105 81-505-607-010 LEAF SW(CRO2 DET.)
SW106 = 81-505~607-010 LEAF SW(REC ENA.)
=== MECHANISM-2 CIRCUIT BOARD SECTION =—
PCB-N *
SOL101 81-507-237-010
SOL102 81-507-237-010
SWi03. 81-505-607-010
MECHANISM-2 CIRCUIT BOARD
SOLENOID 9ME-C
SOLENOID 9ME-C
LEAF SW(CASSETTE DET.)
Sw107
81-505-607-010 LEAF SW(CASSETTE DET.)
=== AUTO STOP CIRCUIT BOARD SECTION ~-=
PCB-O 81-505-605-010 AUTO STOP CiRCUIT BOARD
PD1 87-027-644-010 PHOTO SENSOR NJL-5141EA
PD2 87-027-644-010 PHOTO SENSOR NJL-5141EA
=== MISCELLANEOUS =>
A 87-085-207-010 CORD BUSHING
A 87-034-761-010 AC CORD H(H)
A 87-034-759-010 AC CORD E(E,Z)
A 87-034-760-010 AC CORD K(K,K1)
A 87-034-762-010 AC CORD(C)
D123. 87-020-109-010 = LED SLF~201C(L1IGHT)
EH 87-046-288-010 HEAD,EH
M101 87-045-210-010 REEL MOTOR(REEL)
M102. = 87-045-175-010 MOTOR DC,SYSTEM SERVO(CAPST)
M103: 87~045-210-010 = REEL _MOTOR(PLAY)
A\PT1 82-226-633-010 | POWER TRANSFORMER AUDIO(H)
A\PT1 82-226-637-010 | POWER TRANSFORMER AUDIO(E,Z)
A\PT1 82-226-639-010 | POWER TRANSFORMER AUDIO(K,K1)
A\PT1 82-226-635-010 | POWER TRANSFORMER AUDIO(C)
A\PT2 82~226-634-010 | POWER TRANSFORMER MECHA(H)
A\PT2 82-226-638-010 | POWER TRANSFORMER MECHA(E,Z)
A\PT2 82-226-640-010 | POWER TRANSFORMER MECHA(K,K1)
A PT2 82-226-636-010 | POWER TRANSFORMER MECHA(C)
RPH 87-046-308-010 | HEAD, COMBINATION-AMO PC-OCC
SOL103 82-226-680-010 SOLENOID, SDC-1031
SW101 81-505-601-010 LEAF SW(PLAY)
SW102. 81-505-601-010 = LEAF _SW(PAUSE)
A\ SW108 —-87-031-586-010 = ROTARY SW(AC VOLTAGE) (H)
Combination Circuit Board A 82-226-601-210
PCB-A 82-226-603-210
PCB-B 82-226-602-210
PCB-F 82-226-604-210
PCB-G 82-226-605-210
PCB-H 82-226-607-210
PCB-I 82-226-606-210
PCB-L 82-226-608-210 (K1 MODEL ONLY)
Combination Circuit Board B 82-226-611-210
PCB-C 82-226-612-210
PCB-D 82-226-614-210
PCB-E 82-226-613-210
Combination Circuit Board c 82-226-617-110
PCB-J 82-226-618-110
PCB-K 82-226-619-110
Combination Circuit Board D
PCB-M
PCB-N
86-543-612-010
86-543-613-010
86-543-611-010

IC DESCRIPTION
1, IC, LC6502B—-724
Pin No, Description
Pee ed When K-S IFT is set to “H” When K-S IFT is set to “L”
K-REW/ REC EN key input (Active High)
I RE k i t (Active Lo
K-REC EN, (REC enabled at “H”)
K-PLAY/
PLAY key input (Active Low) TIMER REC input(Active High)
K-TIM*REC
K-STOP/
KENT RES STOP key input (Active Low) Counter Reset input(Active High)
K-FF/ . : TIMER PLAY/Repeat input
FF key input (Active Low) : i
K-TIM*PLY (Active High)
K-PAUSE/ : . Counter “0000” replay input
PAUSE key input (Active Low) ; f
K-CZ*PLY (Active High)
. : Cassette switch input (Active High)
K-REC/K-CST REC key input (Active Low) = ;
(Set to “H” level with cassette}
K-RMT/ Counter “0000” stop input
K-CZ-STP
(Active High)
vi M-CAPST
I
4
4
2
1
2
3
5
I
I
I
I
I
REC MUTE key input(Active Low)
‘e)
Capstan motor control input. Motor tunrs at “H” level.
Sub-motor forward rotation output. Set to “H” in PLAY/REC, FF and
M-FWD
° CUE modes.
M-RVS Sub-motor reverse rotation output. Set to “H” in REW/REV modes.
O-ADMS Not used.
Pause plunger output. Set to “H” PAUSE, PLAY PAUSE, R/P
PAUSE, FF, REW, CUE and REV modes.
Play plunger output. Set to“H” in PLAY, PLAY PAUSE, R/P
PAUSE, CUE and REV modes.
REC MUTE output. Set to “H” when the mechanism is stabilized in the
REC/PLAY anodes.
PLAY MUTE output. Set to “H” when the mechanism is stabilized in
PLAY, REC/PLAY, CUE and REV modes.
REC LED output. Used in O-REC also. Set to “H” in REC, REC/
PLAY, REC/PLAY-PAUSE, REC/PAUSE, REC/PLAY/REC
MUTE modes.
REC MUTE LED output. Set to “H” in REC/PLAY/RMT modes.
Set to “H” every | sec when the RMT key is pressed continuously for 4 sec
1
e
o
1 S-PAUSE
12 S-PLAY
1 O-RMT
14 O-LMT
1
1
3
5 D-REC
6 D-RMT
7
8
1
or more.
Pause LED output. Set to “H” in PAUSE, R/P PAUSE, PLAY/
PAUSE modes,
Play LED output. Set to “H” in PLAY, REC/PLAY, PLAY/
PAUSE, R/P PAUSE modes.
Microprocessor reset input. Gradually changes to +5V from 0V within 3 sec
after power is turned on.
Connected to GND.
Microprocessor clock input (400kHz)
FL counter grid 0, Digit scan output, | place digit.
1
D-PAUSE
1 D-PLAY
RESET
19
22 Osc 1
24 Go
5 5
27 G3
FL counter grid 3, Digit scan output, 1000 place digit.
FL segment output g.
FL segment output a.

Description
ADMS LED output. Set to “H” during slack tape removal and ADMS mode
after power is turned on.
Reel motor voltage control output. Set to “H” in PLAY and REC/PB
modes.
Select key input according to the “H” or “L” state.
Connected to +5V.
Take-up reel rotation pulse input. Auto stop, F L counter and slack tape
removal control.
2.
1C,
HD614042S-A87
High dielectric strength
el} oe
|2\° iwi
Ay
—s
mM \
oO
:
Ww ie] eo] mr
SEG oO FL met ti EG 16 output.
E 16 5 meter section S outpu PULL. DOWN
High dielectric strength
SEG 8 Oo FL meter section SEG 8 output.
PULL DOWN
FL meter section SEG 7 output and SEG DP High dielectric strength
FL meter section SEG 6 output and SEG g High dielectric strength
FL meter section SEG 5 output and SEG f High dielectric strength
FL meter section SEG 4 output and SEG e High dielectric strength
FL meter section SEG 3 output and SEG d High dielectric strength
FL meter section SEG 2 output and SEG c High dielectric strength
FL meter section SEG 1 output and SEG b High dielectric strength
FL meter section SEG 0 output and SEG a High dielectric strength
(The segments light when pins 1-17 are “H” and go off
when they are “L”.) |
4 or 5-wave switching input (number of waves generated
i
jo)
SEG 7
a
1 SEG 6
e bo
SEG 5
ray
3 SEG 4
SEG 3
= a
SEG 2
re n
SEG 1
17 SEG 0
High dielectric strength
PULL DOWN
waves, :
I__| PULL DOWN power (-VDD) for the FL driver,
Motor forward input. “L” input causes forward
I
‘
PULL
UP
rotation.
Motor
reverse
input.
“L”
input
causes
reverse
I
;
PULL
UP
rotation,
Rotation
signal
input
from
mechanism
right
reel
disk
I
PULL
UP
(@R)
Rotation
signal
input
from
mechanism
left
reel
disk
I (¢@L) PULL UP
I
Recording
state
input.
“L”
input
causes
REC
ON.
PULL
UP
Calibration state input. “L” input causes CAL
PULL UP
ON,
FL meter section GRID L output (“L” causes on
C2
PULL
UP
and
“H” causes
off).
FL
meter
section
GRID
R
output
(“L”
causes
on
2
PULL
UP
and
“H” causes
off).
@
A/5
by
the
rotation
of
reel
disk).
“L”
input
causes
5
19 Vpise
20
two
NS
FAIR
wa ie}
vs)
ics) Qa
|
ne)
oy]
Q > e
w ad © as OVA BR
fon) co aad
I} el
Cc
Mm
ive)
ios]
| >
rom) |,
Q Ww
ix}
~]

\
5 Type of Port
FL counter section GRID 0 output (“L” causes on
Ge
PULL
UP
CG
‘
and
“H”
causes
off).
6
aa
Ge
FL
counter
section
GRID
3
output
(“L”
causes
on
PULL
UP
and “H” causes off).
+5V
power
supply.
a
|
MODE
I
Calibration
mode
switching
input
(“L”
causes
Mode
A).
PULL
UP
Meter
muting
input
(“L”
causes
muting
and
“H”
PULL
UP
releases
muting.)
D/A conversion Oth bit (LSB) output (“L” for on and
37 DA O C-MOS output
a potential to be applied).
43
ACE
D/A
conversion
5th
bit
(LSB)
output
(“L”
for
on
and
C-MOS
output
a potential to be applied).
D/A conversion gain switching output (“H” causes
% C-MOS output
20dB attenuation).
Counter reset key input (“L” causes KEY ON). PULL UP
Counter memory key input (“L” causes KEY ON).
External
clock
inputs
(f
=
4.19:
MHz).
ae
I FL output check input (“L” causes check state)
FL
meter
section
SEG
17
output
(“H”
causes
on
and
|
High
dielectric
strength
“L”
causes
off)
PULL
DOWN
FL
meter
section
SEG
23
output
(“H”
causes
on
and
|
High
dielectric
strength
“LL”
causes
off)
PULL DOWN
3. IC, CX20188
2
4
6
Description
Positive power terminal.
La ir wee |
[24a | REC IN
Vs] i eer
a8 |
ee]
Recording inputs.
Reference current input.
Playback inputs.
i
i
Rete] \
(e)
Calibration/recording/playback switching input.
Playback feedback terminals.
Recording feedback terminals.
When
two
power
supplies
are
operating:
Ground
pins,
When
one
pover
supply
is
operating:
Vcc/2
pins.
Line outputs (decoding outputs).
Spectral skewing switching terminals.
1
3
5
,
41
39
3
’
Encoding
circuit
inputs.
HLS highpass filter terminals.
HLS detector time constant terminals 2.
HLS
detector
time
constant
terminals
1.

LLS weighting terminals.
LLS highpass filter terminals.
Anti-saturation terminals.
Recording outputs (encoding outputs).
Dolby NR off/type B/type A switching input. .
Calibration input.
When two power supplies are operating: Negative power supply pin, when one
power supply is operating: Ground pin.
PRACTICAL SERVICE FIGURE
PB output level :
(TTS-200) (TTA-161, TCC-130)
REC/PB output :
(TTA~600)
REC/PB distortion :
Playback noise :
Erase ratio (125Hz) :
Crosstalk :
Channel separation :
Level drift :
(10kHz, TTS-210)
REC/PB S/N ratio:
(WID-A)
(DIN AUDIO)
DBX ON MRL (Dist. 3%)
Level :
Recording bias frequency :
Tape speed :
TTA-100(TTA~111S)
Wow & flutter:
(W.R.M.S)
Take-up torque:
Fast forward torque :
700+ 50mV
(LINE OUT)
OVU-: 2dB
(LINE OUT)
Less than 1.5%
(NORM., Cr0,, MT tapes)
Less than 4.0/3. 5nV
(120 2s/70s, DOLBY NR OFF)
Less than 1,8/1.5mV
(120 2s/70 us, DOLBY NR B)
Less than 1.5/1.3mV
(120 1s/70 2s, DOLBY NR C)
Less than 0.18/0.18mV
(120 2s/704s, DBX, DIN AUDIO)
More than 60dB
More than 45dB
More than 30dB
Within 1dB
More than 45/50dB
(DOLBY C NR OFF/ON with MT,
Cr0, tapes)
More than 40/48dB
(DOLBY C OFF/ON with NORM. tape)
More than 69dB
(DBX ON with MT, Cr0, and NORM.
tape)
+£21VU
(MT, CrO, and NORM. tapes)
105kHz
3kHz+1.5%
Less than 0.023%
(FWD)
38+ 10g-an
(0.380. ImN-m)
120 *28 g-cm
(1.18 19:88 mN-m)
Rewind torque :
Back-tension =
Pinch roller pressure :
Test tape:
€csB
2SA952
2SA1015
2SC945
2SC1815
2SC2001
28C2120
BCE
28C3113
DTA124
DTC114
DTC124
DTC144
RN1202
120 13° g-cm
(1.18 10-28 mN-m)
7.52.5¢-cm
(0.07+0.025mN +m)
350¢ (F side)
(3. 4mN-m)
140g (S side)
(1. 4mN-m)
METAL
Cr0z
NORMAL
TTA~620(TTA-119MP)
TTA-610 (TTA-119H)
TTA~600 (TTA-119K)
2SB1015
2SD1275
25C1846
2SK30

ADJUSTMENT
(CAPSTAN
MOTOR)
CONTROL C.B Y
eS) SFRIOI
1, Play Motor Adjustment (M103) (CONTROL C.B)
Settings : * Test tape : TTA-100(TTA-111S)
* Test point : Both terminals of
PLAY motor (M103)
* Adjustment location : SIFR101(PCB-C)
Method : Play the approximately middle section of
the test tape and adjust SFR101 so the voltage
at the test point is 3.0+0.1V.
. Tape Speed Adjustment
Settings : + Test tape : TTA-100(TTA-111S)
* Test point : LINE OUT jack
+ Adjustment location : SFR in capstan motor
(M102)
Method : Play the test tape and adjust so the frequency
counter reads 3000Hz.
10
AMTG AE MODULATION
TAPE STABILIZER
Initial Settings
* REC VOL : Center
* CAL SW: OFF
* REC EQ : NORM
* BIAS VOL : Center click position
* REC LEVEL VOL : Center click position
+ INPUT SELECTOR SW : LINE
* MPX SELECTOR SW : THRU
* MONITOR SW : TAPE
* NOISE REDUCTION SW : THRU
3. Azimuth Adjustment
Settings : + Test tape : TTS~310(TTA-317E)
* Test point : LINE OUT jack
+ Adjustment location : Azimuth adjustment
screw
Method : Play the 10kHz signal of the test tape and
adjust so the output is maximum and the
vaveforms in the Lissajours figure are in
phase.