Akia Screens Fixed Frame Screen Series User manual

Rev.V04172023DT (DS0230)
www.akiascreens.com
1
Fixed Frame Screen Series
Matte White Fixed Frame Projection Screen
User’s Guide- EN Type
V1
Thank you for choosing an AKIA fixed frame projection screen! Please read through this user guide before
utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points below to
prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it.
Hardware and Parts List
Note: Please make sure all parts are included in your package before proceeding to assemble the screen.
a: Frame parts x 6 pcs
(Springs pre-installed)
b: Elbow Joints x 8 pcs
c: M5*6 screws x 40 pcs
d: Spring hook x 2 pcs
e: Tension Rods x 6 pcs
f: M5*50 wood screws x 8 pcs
g: Wall anchor x 8 pcs
h: Wall brackets x 4 pcs
i: Center support bar x 1 pc
l: Screen Material x 1pc
m: Center joints x 2 pcs

Rev.V04172023DT (DS0230)
www.akiascreens.com
2
Frame Assembly
1. Please wear gloves (j) before installation. (Some models do not include this part.)
2. Insert the center joint (m) connector into to one of the 1/2 horizontal frames and fasten it with two M5*6 screws
(c). Repeat steps for assembling the second horizontal frame.
Center joints (m)
Oblique opening Flat opening
M5*6 screws (c)
Note: a. Two ½ horizontal long frames should be assembled for a screen.
b. Do not tighten the screws completely until all frame pieces have been assembled correctly.
3. Insert both elbow joint (b) connectors into the short vertical frame into slot 1 and slot 2.
Short vertical frame
4. Then insert the horizontal long frames into the exposed elbow joint (b) connectors and fasten them with M5*6
screws (c).
Note: When assembled, please push simultaneously the two ends of the long frames.
Insert the exposed ends of the joint connectors into the frame and align the four corners so that they
meet at perfect right angles.
M5*6 screws (c)
Horizontal long frames
M5*6 screws (c)
Slot 1
Slot 2
elbow joint (b)

Rev.V04172023DT (DS0230)
www.akiascreens.com
3
2
1
2
2
1
2
Attaching the screen material to the frame
1. Unroll the screen material and lay it down on a clean protection sheet (k) (Screen material facing down). Then
Please place the frame gently on the screen material. (Some models do not include this part.)
2. Insert the tension rods (e) separately into the edges of all four corners of the material.
Tension rods (e)
3. Distribute and place spring in the frame one by one corresponding to the holes, (spring has pre-installed in the
frame.)
4. Use spring hook (d) to install screen material, please install four springs at the four corners of the frame in
ABCD order:
Note: Hold the tension rod in the screen material with left hand, hook the spring with right hand, and finally
use the spring hook onto the tension rod in the screen material hole, as shown as below.
A C Spring hook (d)
Springs
Screen material (l)
D B tension rods (e)
5. Install all the spring on screen material, install the spring at position 1, then continue to install the spring at
position 2, then finally install the rest of spring on the screen material, shown as below.
2 2
1 1
2 2

Rev.V04172023DT (DS0230)
www.akiascreens.com
4
Push
Center support
bar (i)
Finished position
Start position
Bracket hole distance
= 1.57” (40mm)
Top wall bracket (h) M5*50 screw (f)
Wall anchor (g)
Wall
Pull
Pull
Center Support Bard
1. Insert the Center Support Bar (i) into the
upper top groove on the back of the frame with
the bottom end near the approximate center
point of the frame and rotate it in at an angle so
that both ends of the bar are in alignment with
the groove, shown as below.
2. Slide the top end of the bar into the top
center point of the frame to complete the center
support bar installation.
This will provide added stability to your frame and added tension to the material.
Installation
Frame
1. Locate your desired installation location with a studfinder (recommended) and mark the drill-holearea of where
the screen is to be installed. Reference the table below for
Unit: mm (inch)
92”
100”
110”
120”
135”
150”
L = Wall bracket distance
1500
(59.1”)
1500
(59.1”)
1800
(70.9”)
2000
(78.7”)
2000
(78.7”)
2500
(98.4”)
H = Top/Bottom Wall
Bracket Height distance
1195
(47.0”)
1294
(50.9”)
1419
(55.9”)
1543
(60.7”)
1729
(68.1”)
1917
(75.5”)
2. Drill a hole with the proper bit size according to the wall anchor (g) and M5*50 screws (f) included.
3. Line up the wall brackets (h) with the drilled holes on the installation location and screw them in using a
screwdriver.
4. Position the fixed frame screen onto the top wall brackets as shown as below info and pull down at the center
of the bottom frame to secure the installation.

Rev.V04172023DT (DS0230)
www.akiascreens.com
5
5. The design of the wall brackets allows the frame to slide over them through its sides. This is an important
feature of the installation design as it allows your screen to be properly centered.
6. Using both hands finish the installation by pulling the lower portion of the fixed frame screen into the lower
bracket as shown as below info.
Caution
Please follow these instructions carefully to ensure proper maintenance and safety of your Fixed Frame Screen.
1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture,
ladders, windows, etc. occupy the space designated for your Fixed-Frame screen.
2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors are
used and that the weight is supported appropriately by a strong and structurally sound surface just as any large
and heavy picture frame should.
(Please consult a home improvement specialist for the best advice on installation)
3. Frame parts are made of high-quality velour-surfaced aluminum and should be handled with care.
4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any other
impurities.
5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen surface.
6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other sharp or
abrasive objects.
8. Spare Parts should be placed out of reach of small children in accordance with household safety guidelines.
For a local AKIA Screens contact or Technical Support, please visit
www.akiascreens.com