Akron GYNAECOLOGY 2 User manual

SERVICEMANUAL
794-026
AKRON
GYNAECOLOGY2
®
Models
9822,9832

Page 1
General Maintenance
?It is recommended that the following checks and adjustments are carried out at
minimum of twice a year and more frequently if the couch is in constant use.
?The framework of the couch is of steel construction and coated
with an epoxy paint finish. This is resistant to most cleaning
substances.
?The major pivot points need to be lubricated sparingly with oil.
Care should be taken to keep oil away from the upholstery.
?All nuts should be checked and tightened where necessary.
Care should be taken not to over tighten the nuts on the pivot
points as this may cause them to bind.
?Air tubes should be checked to ensure that they are not
pinched.
?Disconnect the mains supply and check the following;
NOTE - all electrical checks should be carried out by a suitably
qualified person.
Electric cables and mains plug should be inspected for damage
and replaced where necessary. In addition, electrical safety
checks for earth continuity (class I equipment only) and earth
leakage checks should also be carried out.
The correct value fuse of 5 amps and ASTA approved to
BS1362 MUST be used.
?The upholstered top is manufactured using fire retardant vinyl.
This tends to go brittle if oil or grease (including body oils) are
left on it. The upholstery should be cleaned with warm soapy
water after use. The use of detergents is not recommended
although a suitable sterilization fluid is acceptable. Use of a
couch cover or towel will help prolong the life of the upholstery.
?Woodscrews, used to secure the upholstery, should be checked
and tightened or replaced where necessary.
?The hinge pins on the head and foot sections should be
checked to ensure that they have not moved within the hinge
tubes. If the pin protrudes, a heavy tap with a hammer should
be required to relocate it. If the pin moves easily, the knurling
may be insufficient to hold the hinge pin in place and a new pin
must be fitted.

Page 2
Manufacturers Details
Huntleigh Akron
1 Farthing Road
Ipswich
Suffolk
IP1 5AP
England
Tel. [phone]
Fax. [phone]
Huntleigh Akron T/A a Division of Huntleigh Nesbit Evans Limited
A Member of the Huntleigh Technology PLC Group of Companies
Gynaecology 2 Revision History
DOCUMENT ISSUE DCN No. SIGNED DATE
All Pages 1 936 Gary Mullenger 14/06/00
2M3410Z 2 947 Jason Barker 08/09/00
2M3420Z 2M3421Z 3 951 Jason Barker 23/10/00
2M3424Z 4 964 Jason Barker 15/01/01
A7309 A7310 5 970 Jason Barker 30/03/01

PARTS LIST
2M3411Z SHORT STANDARD BASE ASSEMBLY
2M3411Z – Issue 02
Issue 1 2
Date 9/99 12/99
E.C.N. 908 911
Reference
Number Description Quantity Part Number Issue Status
1H Section 13A2081Z 3
2Link Bar 23A2085Z 0
3Electric Short Standard Wheel Base 13A3676Z 0
4Short Wheel Plunger 43A9406Z 0
5Wheel Cam 23E0112Z 2
6437mm Pivot Pin 13G2089Z 2
722mm Spacer Sleeve 23G2092Z 1
840.5mm Spacer Sleeve 23G3213Z 0
93” Castor 45H0402A 0
10 M10x20 Socket Head Set Screw 45J8058R 0
11 3/4" Grey End Cap 45L0707L 0
12 3/4" Open Star-Lock 45L0906Z 0
13 M10 half Nut 15L3319A 0
14 M10 Spring Washer 45L3351K 0
15 ¼”x1” Seloc Pin 45M0408C 0
16 1700x19 Spring Ring 45M4296S 0
17 8.5mm Grey Insert 45N2100M 0
18 40x40 Moulded End Cap 45N3737M 0
19 40x40x2.5mm Threaded Insert 15N3737V 0
20 40x40x2.5mm Grey Insert 95N3744Z 0
21 10mm Foot Adjusting Stud 15N3782U 0
22 50x25x2.5mm Grey Insert 10 5N3944Z 0
23 Nylon Foot Lever 45T0028Z 1
24 Pedal Rubber 45T3200Z 0
25 Huntleigh Akron Label 15U1006Z 2
26 Pedal Sticker 45U1066Z 1

PARTS LIST
2M3410Z SHORT LARGE WHEEL BASE ASSEMBLY
2M3410Z – Issue 03
Issue 1 2 3
Date 9/99 12/99 9/00
E.C.N. 908 911 947
Reference
Number Description Quantity Part Number Issue Status
1H Section 13A2081Z 3
2Link Bar 23A2085Z 0
3Linking Lug 23A3263Z 0
4Electric Short Large Wheel Base 13A3675Z 0
5Short Wheel Linking Bar 13A3677Z 0
6Hexagonal Cam 13F3251Z 0
740x40x2.5mm Grey Drilled Insert 23F3253Z 0
8437mm Pivot Pin 13G2089Z 2
922mm Spacer Sleeve 23G2092Z 1
10 40.5mm Spacer Tube 23G3213Z 0
11 Short Hexagonal Cam 13H3253Z 0
12 125mm Tente Integral Directional Castor 15H1204E 0
13 125mm Tente Integral Braking Castor 35H1212E 0
14 M6x20 Hex Set Screw 25J7658N 0
15 1/4” Flat Washer 65L0362V 0
16 3/4" Grey End Cap 45L0707L 0
17 3/4" Open Star-lock 45L0906Z 0
18 M6 Nyloc Nut 25L2919C 0
19 12mm Open Capped Star-lock 25L3506Z 0
20 1/4”x1” Seloc Pin 25M0408C 0
21 8.5mm Grey Insert 45N2100M 0
22 40x40x2.5mm Grey Insert 45N3744Z 0
23 50x25x2.5mm Grey Insert 10 5N3944Z 0
24 3/4”x16G Round Grey Insert 25N9251M 0
25 Nylon Foot Lever 25T0028Z 1
26 Pedal Rubber 25T3200Z 0
27 Huntleigh Akron Label 15U1006Z 2
28 Pedal Label 15U1065Z 1
29 Pedal Label 15U1066Z 1

PARTS LIST
2M3412Z 230v TRIPLE MAGNETIC RAM KIT
WITH BATTERY BACKUP
2M3412Z – Issue 03
Issue 1 2 3
Date 9/99 12/99 3/00
E.C.N. 908 911 930
Reference
Number Description Quantity Part Number Issue Status
1Motor Mounting Bracket 13A2006Z 0
2Ram Fixing Pin 13A2088Z 0
3LHS Control Mounting Bracket 13A3652Z 0
4RHS Control Mounting Bracket 13A3660Z 0
510mm Spacer 43G9434Z 0
620mm Spacer 23G9437Z 0
7230v/24v Magnetic Control Box 15F8500Z 0
8Max30-A150425A04200-000 15F8600Z 0
9Max10-A100295A16100-000 15F8610Z 0
10 Max10-A100295A20200-000 15F8620Z 0
11 M8x55 Hex Ht Bolt 45J7865A 0
12 M8x60 Hex Ht Bolt 25J7866A 0
13 M12x50 Hex Ht Bolt 25J8264A 0
14 M12x60 Hex Ht Bolt 25J8266A 0
15 M12x65 Hex Ht Bolt 15J8267A 0
16 No.10x1/2” Pan Head Screw 55K0407X 0
17 M5x20 Pan Head Screw 45K1137N 0
18 M5 Nyloc Nut 45L2819C 0
19 5mm Shake-proof Washer 15L2855K 0
20 M5 Flat Washer 85L2865K 0
21 M8 Nyloc Nut 65L3119C 0
22 M8 Flat Washer 45L3162K 0
23 12mm StarLock Capped 25L3503Z 0
24 M12 Nyloc Nut 55L3519C 0
25 M12 Flat Washer 10 5L3562K 0
26 M12 Nylon Washer 65L3577X 0
27 M8 Nut Cap 25N0028X 0
28 M12 Nut Cap 55N0030X 0
29 60x40x3 Grey Insert 45N4144Y 0
30 1.5mm Earth Wire 0.12 5S0216Z 0
31 Cable Tie 35S0315Z 0
32 Push Mounted Cable Tie 25S0318Z 0
33 Small Curly Wrap 0.6 5S0326Z 0
34 Large Curly Wrap 0.7 5S0327Z 0

PARTS LIST
2M3412Z 230v TRIPLE MAGNETIC RAM KIT
WITH BATTERY BACKUP
2M3412Z – Issue 03
Issue 1 2 3
Date 9/99 12/99 3/00
E.C.N. 908 911 930
Reference
Number Description Quantity Part Number Issue Status
35 5mm Crimped Eyelet 25S0335Z 0
36 Control Box Cover 15T0055Z 0
37 Serial Number Label 1760.43 1

PARTS LIST
2M3414Z 115v TRIPLE MAGNETIC RAM KIT
WITH BATTERY BACKUP
2M3414Z – Issue 03
Issue 1 2 3
Date 9/99 12/99 3/00
E.C.N. 908 911 930
Reference
Number Description Quantity Part Number Issue Status
1Motor Mounting Bracket 13A2006Z 0
2Ram Fixing Pin 13A2088Z 0
3LHS Control Mounting Bracket 13A3652Z 0
4RHS Control Mounting Bracket 13A3660Z 0
510mm Spacer 43G9434Z 0
620mm Spacer 23G9437Z 0
7115v/24v Magnetic Control Box 15F8400Z 0
8Max30-A150425A04200-000 15F8600Z 0
9Max10-A100295A16100-000 15F8610Z 0
10 Max10-A100295A20200-000 15F8620Z 0
11 M8x55 Hex Ht Bolt 45J7865A 0
12 M8x60 Hex Ht Bolt 25J7866A 0
13 M12x50 Hex Ht Bolt 25J8264A 0
14 M12x60 Hex Ht Bolt 25J8266A 0
15 M12x65 Hex Ht Bolt 15J8267A 0
16 No.10x1/2” Pan Head Screw 55K0407X 0
17 M5x20 Pan Head Screw 45K1137N 0
18 M5 Nyloc Nut 45L2819C 0
19 5mm Shake-proof Washer 15L2855K 0
20 M5 Flat Washer 85L2865K 0
21 M8 Nyloc Nut 65L3119C 0
22 M8 Flat Washer 45L3162K 0
23 12mm StarLock Capped 25L3503Z 0
24 M12 Nyloc Nut 55L3519C 0
25 M12 Flat Washer 10 5L3562K 0
26 M12 Nylon Washer 65L3577X 0
27 M8 Nut Cap 25N0028X 0
28 M12 Nut Cap 55N0030X 0
29 60x40x3 Grey Insert 45N4144Y 0
30 1.5mm Earth Wire 0.12 5S0216Z 0
31 Cable Tie 35S0315Z 0
32 Push Mounted Cable Tie 25S0318Z 0
33 Small Curly Wrap 0.6 5S0326Z 0
34 Large Curly Wrap 0.7 5S0327Z 0

PARTS LIST
2M3414Z 115v TRIPLE MAGNETIC RAM KIT
WITH BATTERY BACKUP
2M3414Z – Issue 03
Issue 1 2 3
Date 9/99 12/99 3/00
E.C.N. 908 911 930
Reference
Number Description Quantity Part Number Issue Status
35 5mm Crimped Eyelet 25S0335Z 0
36 Control Box Cover 15T0055Z 0
37 Serial Number Label 1760.49 1

PARTS LIST
2M3417Z GYNAECOLOGY 2/3 TOP FRAME
2M3417Z – Issue 02
Issue 1 2
Date 9/99 12/99
E.C.N. 908 911
Reference
Number Description Quantity Part Number Issue Status
1Hinge Pin 23A3181Z 2
2Mid Frame 13A3602Z 5
3Gynae 2 & 3 Backrest 13A3678Z 0
4Gynae 2 & 3 Tilt Frame 13A3681Z 0
5Sliding Debris Tray Holder 13A3682Z 0
6Gynae 2 & 3 ABS Guard 13F3684Z 0
7335mm Pivot Pin 13G2090Z 2
8161.5mm Spacer Sleeve 23G2091Z 0
922mm Spacer Sleeve 23G2092Z 1
10 H Section Pivot Pin 13G3211Z 2
11 10.5mm Spacer Sleeve 23G3212Z 1
12 369mm Pivot Pin 13G3604Z 2
13 42mm Spacer Sleeve 23G3605Z 0
14 21mm ABS Guard Spacer 23G3686Z 0
15 M6x60 Hex Ht Bolt 25J7666A 0
16 M6x25 Pan Head Set Screw 45K1238U 0
17 M6x40 Pan Head Set Screw 45K1241U 0
18 ¼” Washer Flat Form D 45L0362V 0
19 3/4" Grey End Cap 65L0707L 0
20 3/4" Open Star-Lock 65L0906Z 0
21 M6 Nyloc Nut 25L2919C 0
22 R Clip 25M0300R 0
23 1"x1"x14G Grey Insert 45N0948Z 0
24 8.5mm Grey Insert 85N2100M 0
25 50x25x2.5mm Grey Insert 10 5N3944Z 0
26 Debris Tray 15T7900Z 0
27 Bush 4796.237 0

PARTS LIST
A7317 SLIDING LEG SUPPORT ASSEMBLY
2M3420Z – Issue 03
Issue 1 2 3
Date 9/99 6/00 10/00
E.C.N. 908 936 951
Reference
Number Description Quantity Part Number Issue Status
1Leg Support Socket 23A3624Z 0
2M10x42 Brass Stud 43G4431Z 0
3M10 Half Nut 45L3319A 0
4Single Pin Button Lock 25M2850P 0
5M10x2-1/4” Knob 45N1582N 0
645x20x14-20G Insert 25N3832Z 0

PARTS LIST
A7318 ACCESSORY MOUNTING BRACKET ASSEMBLY
2M3421Z – Issue 03
Issue 1 2 3
Date 9/99 6/00 10/00
E.C.N. 908 936 951
Reference
Number Description Quantity Part Number Issue Status
1Arm Rest Bracket 23A3689Z 0
2Arm Rest Fixing Plate 23F3695Z 0
3M10x25 Brass Stud 23G5023Z 1
4M8x40 CSK Allen Screw 45J7862U 0
5M10 Half Nut 25L3319A 0
62-1/4"x M10 Knob 25N1582N 0

PARTS LIST
2M3422Z A7303 SEAT EXTENSION
2M3422Z – Issue 03
Issue 1 2 3
Date 9/99 3/00 6/00
E.C.N. 908 927 936
Reference
Number Description Quantity Part Number Issue Status
1Seat Section Loop 13A3683Z 1
2M10x42 Brass Stud 13G4431Z 0
3M6x40 Pan Head Set Screw 45K1241U 0
4M10 Half Nut 15L3319A 0
51”x1”x16G Rounded Insert 25N0909M 0
62 ¼”xM10 Knob (Red) 15N1560N 0