2000 Series Fold Down Seat- 02130/P
Installation and User Care Instructions
ESSENTIAL INSTALLER INFORMATION
Never exceed the weight capacity of 25stone/158kg/350lb
Adjust support legs ensuring that both legs sit firmly on a
flat surface, (maximum 1 in 40 shower base slope), when
placed in the down position.
Curved surfaces such as corners of bathtubs are not
acceptable.
This seat must be attached to a vertical surface using suitable
fixings appropriate to the type of surface and loading
conditions to be applied.
Stainless steel fixings are recommended.
Make sure all fixing holes are used. Take care not to damage
the painted surface. Do not add countersinks screws or make
any holes larger. This can reduce the strength of the frame
and invalidate any warranty or weight capacity stated.
Colour: WHITE RAL 9016 / Grey to RAL 7035 or High Contrast Blue to RAL 5005 Internal Building use only
1Position the seat pad to seat.
Note the front of the pad is
indicated.
The seat pad retainer
caps are fitted from
underneath the seat.
Each pad locating bung
has a retainer (4 in total)
Covered by one or
more of the following
Registered Designs:
GB 3011017, EU
000548607
USA 29/249106
Pat apps:
USA 11/456352,
EU 06253480
4
3
2
If a SEAT PAD is not fitted, please ensure that plugs are fitted to all holes.
UK
Read ALL instructions carefully BEFORE installation and leave with the end user
ESSENTIAL INSTALLER INFORMATIONESSENTIAL INSTALLER INFORMATION
Cushion AssemblyCushion Assembly
ALWAYS Read these installation instructions
carefully before installing this product
and leave with the end user FOR FUTURE
REFERENCE.
ALWAYS Have the seats installed by a trained and
experienced installer.
Make the seat height suitable for the
user.
ALWAYS Attach this Seat to a surface using fixings
matched to the type of surface and
the loading conditions to be applied.
ALWAYS Use hole reducers if seat cushions are not
used.
NEVER Exceed the weight capacity of 25 stone
(158 Kg) (350 Ib)
NEVER Install countersunk screws to fixing holes.
NEVER Stand on the shower seat. This may
reduce the strength of the shower seat
and will invalidate any warranty or weight
capacity stated.
DO NOT Place matches or cigarettes on or near
this product.
The following plastic materials are used
in this product:
Polypropylene(PP), Poly Vinyl Chloride
(PVC-U) Thermoplastic Rubber (TPR).
High Density Polyethylene (HDPE)
Polyurethane Foam (PU)
No natural Rubber or Latex used in this
product.
BEWARE A pinch hazard may be present around
the region of the leg mechanism during
the raising and lowering of this seat.
BEWARE making fixing holes larger will reduce the
strength of the seat and invalidate any
warranty or stated weight capacity.
The AKW 2000 series shower seats conform to the requirements of the EU Council directive
93/42/EEC for a class 1 non-invasive transient use device, using the following harmonized
European standards in the confirming assessment: BS EN 12182:1999, BS EN 12727:2000
Failure to install this AKW product in
accordance with supplied instructions or
the making of unauthorised modications
will invalidate any warranty and will
affect product safety.
Orderline
01905 823299
General Enquiries
01905 823298
Technical Help line
01905 560219
Fax
01905 823297
Website
www.akw-ltd.co.uk
Quotes & orders email
Enquiries email
Post
AKW, Pointon Way,
Hampton Lovett,
Droitwich Spa,
WR9 0LR
This product conforms to the essential requirements of the Medical Devices
Directive 93/42/EEC and representative samples have been evaluated under
EN12182:1999 and EN12727:2000 For use solely as a shower seat (assistive,
Class 1 device).
Declaration issued under the sole responsibility of the manufacturer.
© 2014 AKW 06-002-045-01
IMPORTANT SAFETY INFORMATION
ALWAYS
ALWAYS
ALWAYS
ALWAYS
NEVER
NEVER
NEVER
DO NOT
BEWARE
BEWARE
For the latest AKW product news
scan this QR code with your device.
The measurements throughout these installation and user care instructions have been converted from metric to its equivalent in imperial, therefore all dimensions are approximate and
subject to manufacturing tolerances. These instructions are provided to advise the minimum standards of installation and recommendswhat is the best practice for the installation. Due to the
very wide variability of possible installation conditions AKW cannot provide all circumstances for the installation. AKW cannot accept any liability in connection with this information or its use. This
information is provided on the condition that the person receiving it shall make their own tests to determine the suitability for their particular purpose. Failure to install this AKW product in
accordance with supplied instructions or the making of unauthorised modifications will invalidate any warranty and may affect product safety. None of the foregoing affects your statutory rights. Retainer cap
To fit the retainer cap, it should be
rotated in a clockwise direction whilst
applying firm pressure towards the
seat pad.
The seat pad may
need to be held
in position whilst
the retainer caps
are fitted.
Be careful not to
overtighten the
retainer caps.
The retainer should be
hand tightened so that it is
a secure fit.
What to do if something goes wrong?
In the unlikely event that you should
encounter a problem with this product,
please contact your local installer and
if this does not resolve the issue then
contact AKW technical
team who will provide further advice
and if necessary arrange for our service
engineer to visit or discuss our
comprehensive after-sales service. As
part of our quality and training program
calls may be monitored or recorded.
None of the forgoing affects your
statutory rights.
