Akw Bama User manual

Please read all instructions before installation and leave this document with the end user for
future reference as it contains important warranty information
Bama Shower Seat
INSTALLATION INSTRUCTIONS

General: 01905 823 298 | www.akw-ltd.co.uk
2
Important Information
Mounting Bracket Dimensions
490 mm
409 mm
357mm
340mm
480mm
± 15
± 15
357 mm
45mm
7mm
90 mm
210 mm
250 mm
160 mm
490 mm
409 mm
357mm
340mm
480mm
± 15
± 15
357 mm
45mm
7mm
90 mm
210 mm
250 mm
160 mm
Seat Dimensions
Before you start
Remove all packaging and examine the product for any damage or manufacturing faults. Notify the retailer
immediately if damage or faults are found. Check that all items are present before discarding any packaging.
The manufacturer cannot be held responsible for any installation costs that may arise from damaged or faulty
products being installed and not in accordance with these instructions.
The guarantee does NOT cover impact related damage, see warranty details. Please dispose all packaging in
accordance with local recycling authorities.
Important Information
This seat must be attached to a vertical surface using suitable xings appropriate to the type of surface and loading
conditions to be applied. Ensure that both legs sit rmly on a at surface, (maximum 1 in 40 shower base slope),
when placed in the down position. Curved surfaces such as corners of bathtubs are not acceptable.
Safety
Ensure the wall type is suitable for this installation. Max 200kg load rating (depending on the wall type and
suitable xings). The maximum load rating for this seat is subject to the product being correctly tted to a suitable
wall/ mounting surface and the product being used on a suitable shower tray or oor surface. Acrylic shower trays are
not suitable for use with this product. Always check for hidden pipe work or electrical wires before drilling.
– Do not stand on this seat.
– Always sit in the middle.
– Be aware of possible nger traps or pinch hazards.
– Children should be supervised at all times when using this seat.
– Keep children away from small parts and packaging.
– Please dispose all packaging in accordance with the local recycling authorities.
3 2 1
X X
Never exceed the weight capacity of
31stone / 200kg / 440lb
Do not use xings with
Countersunk heads.
Fixings not supplied.
Installation must be carried out in accordance with these
instructions, and must be conducted by a qualied and
competent installer.

Technical Support: 01905 560 219Order: 01905 823 299 |orders.akw-ltd.co.uk
3
Installation Instructions
Determine the user height of the seat and measure
this height against the wall. Adjust the feet to make
ner adjustment. Remove the bracket cover.
Use a piece of masking tape to mark the tiled wall
and to protect the tile from splintering. Drill the
holes with a suitable wall / tile drill piece. Fixings not
supplied.
Do not over-tighten xings. Check the seat operation,
levels and leg positioning when it is raised and
lowered. Replace the bracket cover.
Use suitable wall xings to secure the mounting
bracket to the wall. Do not use countersunk screws
as this can reduce the strength of the seat and will
invalidate any warranty or weight capacity stated.
To adjust the rate the seat lowers, tighten or loosen
the linkage bolt under the seat with a 6mm Allen key.
Mark the position of the mounting bracket holes
on the wall ensuring the seat is level. Check for any
obstacles or pipework before any drilling or xing.
±
15
±
15mm

13-016-055-04 UK© AKW Medi-Care Limited 2021
Follow us on Social:
Contact
Orders & Quotes
01905 823 299
[email protected]
General Enquiries
01905 823 298
[email protected]
Technical Enquiries
01905 560 219
[email protected]
Kitchen Enquiries
01905 823 262
[email protected]
Fax
01905 823 297
AKW
Pointon Way, Hampton Lovett
Droitwich Spa, WR9 0LR
www.akw-ltd.co.uk
orders.akw-ltd.co.uk
Guarantee
The life time guarantee applies only
to manufacturing or material defects,
conditional on the one-time correct
installation of the product.
Does not apply to:
• Inappropriate use or accidental
damage.
• Damage or defects that result from
incorrect installation.
• Lack of maintenance including the
build up of grime or damage resulting
from inappropriate cleaning.
• Damage or defects that result from
repairs or modications undertaken by
unauthorised persons.
• This guarantee excludes general wear
and tear through usage and does not
apply to surface nishes.
What to do if something goes wrong?
In the event that you should encounter a
problem with this product, please contact
your local installer and if this does not
resolve the issue, then contact AKW
technical team who will provide further
advice and, if necessary, arrange for a
maintenanceengineertovisitandreportany
issues. See the T&Cs on our website or our
catalogue for further information. None of
the foregoing affects your statutory rights.