ALC AT199 User manual

1
ALC Nose
AT199 Breath Alcohol Tester
'ALC Nose' breath alcohol tester should be used only to give an indication of the possible
presence of alcohol in the breath/blood. You should not rely upon it as the sole basis to
determine intoxication or whether it is safe to drive a vehicle, operate equipment, or engage in
dangerous activities.
Everyone has different body responds to alcohol consumption and his testing result only
as reference, not a subject standard for consequent decision.
The manufacturer, importer or distributor takes no responsibility whatsoever for the use
of this product for any reason. This product must not be used as a tool for determining whether
a person is able to operate a motor vehicle or device legally or safely. The intake of any
alcohol will impair reflexes and judgment to operate motor vehicle.
Main Features:
Advanced flat surfaced alcohol sensor
Quick response, excellent accuracy
Smart MCU control
Direct testing process LCD Indication
LCD Indication, word pattern with backup
lamp
Portable design
No touch healthy breath design
Visible and audio warning beyond pre-set
limit
Power saving design, low battery indication
Technlcallnfonnatlon:
Sensor Type: Flat-surfaced Alcohol Sensor
Detection Range: 0.00 - 0.20%BAC, 0.00-2.00%oBAC
0.00 - 1.00mg/L; 0.00 - 2.00g/L Accuracy: ±10% F.S.
Pre-set Level: 0.05%BAC; 0.50%oBAC; 0.25mg/L; 0.50g/L
Warm-up Time: 18 counting down
Testing Time: < 8 Sec
Display: 3 digitals LCD
Power: 3V DC C2xAAA batteries)
Working Environment: -10'C - 50'C ≤ 95%RH (No dews)
Dimensions: 104mm X 40mm X 18mm @38g (exclusive batteries)

2
Indication:
0.0 mg/L
WAIT
Breathed Alcohol Contents
In Warm-up, please Wait
Battery used up, please replace
The 'ALC Nose' breath alcohol tester can be quick for detection of alcohol in the breath.
If you are in excessive drink, the tester would give you audio warning beyond pre-set limit.
Operation Instruction:
1. Slide down to open the battery compartment, insert the batteries and close it carefully,
please note the correct polarity direction in the battery compartment, otherwise, you may
damage the unit.
2. Press the 'switch' button for 1sec, the backup lamp would on, with a buzzer brief
ringing the 'Wait' flashes and Warm-up of 018, 017, 016". 000 counting down, until 'Wait'
disappears, and the 'C' and 'blow' guide you to have a testing.
3. Blow into the 'Gas Entry', when the 'C' appears, please have a deep breath and
breathe out directly and equably to gas entry for about 3-4S, don't stop until the buzzer rings.
It's better to keep 3-4cm interval from your mouth to gas entrance.
4. Read the result: after breath out, the LCD would give you the readout of your alcohol
contents, the result would be kept on the screen for seconds, with a buzzer ringing, the tester
will be power off automatically.
5. If a new testing needed, please press the switch button again and repeat the above
steps.
Notification:
1. Avoid any strong shock and drop to keep the tester in careful package or deposit.
2. Do not wipe it with any cleaning agent. If high concentration noise gas exists, the
normal testing would be disturbed.
3. The result may be unreliable for your first twice tests if long time storage, please try
again.
4. To ensure the testing result, please wait 15 min to take the testing after your drinking.
5. Do not use or store the tester in the environment with aggressive gas (such as chlorine
gas).6. The working life of the sensor is more than 2 years in the normal operating
environment.
7. To ensure the accuracy of the tester, please make a calibration at least 3 "months.

3
Ordinary faults and solutions:
.
Fault description
Possible fault reasons
Solution methods
WronQ installation
Install the batteries by the correct polarity
direction
Low batterv
Reo lace new batteries
LCD without displaying
Contact with dealer or manufacturer for
Circuit fault
maintainina
Retardation time
No response for target
doesn't end
Wait for the retardation time finish
gas
Contact with dealer or manufacturer for
Circuit fault
maintainino